Documents by Year

1950s (3)

1960s (28)

1970s (324)

1980s (132)

1990s (44)

2000s (11)

2010s (2)

RTM

1975

«
1
2
»

RTM 108.020.01-75

Strength calculation of pipelines of nuclear power plants

RTM 16.689.169-75

Explosion-proof and mine electrical equipment repair

RTM 24.020.30-75

Test method of combined-cycle plants

RTM 24.020.33-75

Stationary steam and gas turbines, compressors. Labyrinth seals, type selection and leakage calculation

RTM 24.030.33-75

Calculation of the strength of the main bearing elements of low and high pressure heaters for high-power units

RTM 24.030.48-75

High-pressure steam generator PGU. Feed water and steam quality standards

RTM 24.030.49-75

Method of accounting for scaling when calculating the strength of the elements of the heating surfaces of steam boilers

RTM 24.030.50-75

Calculation of the efficiency of preheating of air at power plants

RTM 24.030.51-75

Stationary steam boilers. Selection and calculation of nozzle devices of blowing devices for heating surfaces of boiler units

RTM 24.038.12-75

Selection of resilient supports for piping of thermal and nuclear power plants.

RTM 24.250.27-75

Stationary steam boilers. Steelworks. Framed and welded assemblies. Types and basic dimensions

RTM 26-07-182-75

Corrosion protection of pipeline fittings by a gumming compound based on nairit NT

RTM 26-07-183-75

Application of standards of the Unified System for Design Documentation (ESKD) in the valve industry

RTM 26-07-184-75

The procedure for the development of design documentation for rubber technical products for pipe fittings

RTM 26-07-185-75

Experimental design determination of thermal characteristics in electric gland valves for environments with temperatures up to 450 ° C

RTM 26-07-186-75

The procedure for determining, planning and monitoring the level of unification of pipelines for valves and actuators for it

RTM 26-07-187-75

Casting of parts of pipe fittings of radius of curvature and casting transitions. Wall thickness

RTM 26-07-188-75

The use of thermal resistance in the nodes of cryogenic reinforcement. Non-metallic thermal stock connectors

RTM 26-07-189-75

Statistical regulation of technological processes by the method of medians and individual values

RTM 26-07-190-75

Permanent map of statistical regulation of technological processes in machine shops

RTM 26-07-191-75

Control over the implementation and compliance with the production standards and other regulatory and technical documents on general industrial valves and actuators to it

RTM 26-07-192-75

Material symbol in the design documentation

RTM 26-07-193-75

Program for calculating the temperature fields of cryogenic pipeline valves on a computer

RTM 26-07-194-75

Reliability indicators of the main types of general industrial pipeline fittings. Quantitative indicators

RTM 26-07-195-75

The order of installation and regulation of typical signaling nodes. Switch type BPT-2

RTM 26-07-196-75

The order of installation and regulation of typical signaling nodes. Sensors DBPM-3, DBKPTM-3a and signaling devices SPKM-3a, SKPUM-D3a-R

RTM 26-07-197-75

The procedure for obtaining a passport for industrial pipe fittings

RTM 26-07-199-75

Test system for testing pipeline valves. Periodic testing. Main provisions

RTM 26-07-200-75

The procedure for the design and application of typical calculations of pipe fittings and actuators for it

RTM 26-07-201-75

Sealing technology of coils of electromagnets

RTM 26-07-202-75

The dependence of the service life of valve valves on the specific pressure on the sealing surface

RTM 26-07-203-75

Surfacing of sealing surfaces of pipeline fittings UONI-13/H1-BK with electrodes UONI-13/H1-BK

RTM 26-07-204-75

Method for calculation of full-lift safety valves of the hung throughput capacity

RTM 26-07-205-75

Climatic tests of pipe fittings

RTM 26-07-206-75

Ball valves. Construction of valve assemblies with fluoroplast-4 seal

RTM 26-08-15-75

Typical control scheme for clamping the upper shaft of the press

RTM 26-08-26-75

Pipeline connections (GOST restriction)

RTM 26-08-32-75

Method of heat engineering calculation of the drying part of paper-board-making and drying machines using computers

RTM 26-12-09-75

Safety valves spring full-lift piston compressors. Calculation methods

Automated control systems in the industry of chemical and petroleum engineering "ASU-Himmash" and ASUP. Information Support. Basic concepts. Terms and Definitions

Orghosnast unified

Research and development reports. General requirements

Examples of execution of drawings of products of chemical and petroleum engineering

System of operational production planning, accounting and dispatching in chemical and petroleum engineering

Improving the industry management system through the creation of software and NGOs. Guidelines for building organizational structures for managing associations

Improving the industry management system through the creation of software and NGOs. The main stages of the creation of associations and the economic conditions of their formation

Cutting of round and profile rolled products with an abrasive tool. Basic process requirements

Borehole oil sucker-rod pumps with a sleeve cylinder and a metal plunger. Typical process of machining bushings

«
1
2
»

All Codes and Regulations

Codes	MGSN	OND	PR	SNiP	TU
Decisions	MI	ONTP	PUE	SN	VNTP
Decrees	MR	Orders	RD	SO	VPPB
GN	MSN	OST	RDS	SP	VRD
GOST	MSP	Other norms	Resolutions	ST SEV	VSN
Instructions	MUK	PB	RMU	STO
Laws	MU	PNAE	R	TI
Letters	ND	PND	RSN	TOI
MDK	NPB	POT	RTM	TR EAES
MDS	NP	PPB	SanPiN	TSN

All Categories

Construction (Max)	Highways (Max)	National Standards for KGS (State Standards Classification)	Power industry	Standards for pipe fittings (TPA)
Construction Price Formation	ISO classifier	National Standards for OKSTU	Projects of works (PPR) on bridges	Technical Supervision
Evidence base (TR CU, Technical Regulation of the Customs Union)	National standards	Organization Standards	PromExpert	Welding regulations

©RGTT 2016. All Rights Reserved.

Send us a message

Leave your message in the form below, and we will write back by e-mail!