RD 03-380-00
РД 03-380-00
|
|
Guidelines for Inspection of Spherical Tanks and Gas Holders for Storage of Liquefied Gases Under Pressure
Инструкция по обследованию шаровых резервуаров и газгольдеров для хранения сжиженных газов под давлением
Status: Effective
The requirements of this Instruction apply to the conduct of a comprehensive technical inspection of ground-based steel welded ball tanks and gas-holders with a volume of 25 to 2000 m3 or more for the storage of flammable liquids (EIR), liquefied gases (LPG, LNG), compressed gases, aggressive products (acids) and sparkling wines under pressure from 0.25 to 1.8 MPa at climatic and isothermal temperature conditions.
Требования настоящей Инструкции распространяются на проведение комплексного технического обследования наземных стальных сварных шаровых резервуаров и газгольдеров объемом от 25 до 2000 м3 и более для хранения легковоспламеняющихся жидкостей (ЛВЖ), сжиженных газов (СУГ, СПГ), сжатых газов, агрессивных продуктов (кислот) и игристых вин под давлением от 0,25 до 1,8 МПа при климатическом и изотермическом температурном режиме.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosgortekhnadzor of Russia,
9/20/2000
SKU: RUSS145131
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Regulatory documents of supervisory authorities »
Regulatory documents of Gosgortekhnadzor »
Technical Supervision »
Section I. Technological, construction, energy supervision and environmental protection regarding limitation of negative anthropogenic impact »
IV. Regulatory legal acts and regulations »
2. Industrial safety »
2.1. Common to various hazardous production facilities »
PromExpert »
SECTION IV. INDUSTRIAL SAFETY »
II Industrial safety requirements for operation of a hazardous production facility »
2 Special industrial safety requirements for operation of a hazardous production facility »
2.2 Industrial safety requirements in oil and gas industry »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.020 Storage tanks for liquids and gases »
23.020.30 Pressure vessels, gas cylinders »
The Document References:
GOST 10885-85: Hot-rolled two-ply corrosion-resistant steel sheets
GOST 12.2.003-91: Industrial equipment. General safety requirements
GOST 12730.0-78: Concretes. General requirements for methods of determination of density, moisture content, water absorptions porosity and watertightness
GOST 12730.2-78: Concretes. Method of determination of moisture content
GOST 12730.5-84: Concretes. Methods for determination of water tightness
GOST 14249-89: Vessels and apparatus. Norms and methods of strength calculation
GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods
GOST 1497-84: Metals. Methods of tension test
GOST 17624-87: Concrete. Ultrasonic method of strength determination
GOST 18105-86: Concretes. Rules for the strength control
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 18661-73: Steel. Method for measurement of hardness by shock indentation
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 22266-94: Sulphate-resistant cements. Specifications
GOST 22536.0-87: Carbon steel and unalloyed cast iron. General requirements for methods of analysis
GOST 22536.12-88: Carbon steel and unalloyed cast iron. Methods for determination of vanadium
GOST 22536.14-88: Carbon steel and unalloyed cast iron. Methods for determination of zirconium
GOST 22690-88: Concretes. Determination of strength by mechanical methods of nondestructive testing
GOST 22761-77: Metals and alloys. Brinell hardness test by static action portable hardness meters
GOST 22762-77: Metals and alloys. Yield point hardness test by ball indentation
GOST 22904-93: Reinforced concrete structures. Magnetic method for determining the thickness of the protective layer of concrete and the location of reinforcement
GOST 24289-80: Eddy current non-destructive testing. Terms and definitions
GOST 24755-89: Vessels and apparatus. Norms and methods of strength calculation for openings reinforcement
GOST 25221-82: Vessels and apparatuses. Spherical non-sided heads and bottoms. Norms and methods of strength calculation
GOST 25859-83: Steel vessels and apparatuses. Norms and methods of fatigue strength calculation under low-cyclic loads
GOST 26202-84: Vessels and devices (standards and methods of design calculations of strength for shells and bottoms under supporting loads)
GOST 27772-88: structural steel structure rolled products. General specifications
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 28570-90: Concretes. Methods of strength evaluation on cores drilled from structures
GOST 28702-90: Non-destructive testing. Ultrasonic thickness gauges. General technical requirements
GOST 2999-75: Metals and alloys. Vickers hardness teat by diamond pyramid
GOST 3242-79: Welded joints
GOST 380-2005: Common quality carbon steel. Grades
GOST 380-94: Normal quality carbon steel
GOST 5520-79: Carbon, low-alloy and alloy sheet steel for boilers and pressure vessels. Specifications
GOST 5639-82: Steel and alloys. Methods for detection and determination of grain size
GOST 5640-68: Steel. Metallographic method for determination of microstructure of sheets and bands
GOST 7350-77: Plate, corrosion-resistant, heat-resistant, and high-temperature steel
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 7564-73: Steel. General rules of samples, blanks and test pieces for mechanical and technological tests
GOST 7564-97: Rolled products general rules of samples, rough specimens and test pieces selection for mechanical and technological testing
GOST 9012-59: Metals. Method of Brinell hardness measurement
GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature
OST 26-1103-74: Surface gas-flame tempering. Continuous-consecutive method. Typical process
OST 26-291-94: Steel welded vessels and devices. General technical requirements.
PB 03-110-96: Safety regulations on pressurized storage of liquefied petroleum gas and highly inflammable liquids
PB 03-246-98: Rules for audit of industrial safety
PB 03-576-03: Regulations of design and safe operation of pressure vessels
PB 09-170-97: General rules on explosion safety for explosive- and fire-hazardous chemical, petrochemical plants and oil refineries
PB 10-115-96: Regulations of design and safe operation of pressure vessels
RD 03-131-97: Regulations on Arrangement and Conducting of Acoustic-Emissive Control of Vessels, Units, Boilers and Process Pipelines
RD 03-410-01: Instructions on the procedure of comprehensive engineering certification of cryogenic tanks for liquefied gases
RD 03-420-01: Guidelines for Inspection of Reinforced Concrete Tanks for Petroleum and Petroleum Products
RD 153-39.4-078-01: Operation Requirements for Tanks on Trunk Petroleum Product Pipelines and at Petroleum Depots
RD 39-0147103-378-87: Guidelines for Repair of Prestressed Reinforced Concrete Cylindrical Petroleum Tanks
Recommendations: Aspiration smoke-sensitive alarms VESDA. Part 1. Scope
SNiP 2.03.11-85: Corrosion protection of buildings structures
SNiP 3.03.01-87: Bearing and enclosing structures
SNiP 52-01-2003: Concrete and ferroconcrete structures. Principal rules
The Document is Referenced By:
Order 498: List of questions proposed in the qualification examination for certification of experts in the field of industrial safety
RD 03-410-01: Instructions on the procedure of comprehensive engineering certification of cryogenic tanks for liquefied gases
RD 03-420-01: Guidelines for Inspection of Reinforced Concrete Tanks for Petroleum and Petroleum Products
RD 26.260.16-2002: Expert technical diagnostics of vessels and equipment operating under pressure at gas and gas condensate and oil production and processing facilities in the northern regions of the Russian Federation and underground gas storage facilities
SP 343.1325800.2017: Constructions of the industrial enterprises. The rules of operation
SP 43.13330.2012: Structures for industrial installations
Customers Who Viewed This Item Also Viewed:
|
Controllers acting without
Language: English |
Building materials. Methods for combustibility test
Language: English |
Building materials spread flame test method
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Clear sheet glass. Specifications
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
|
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.