ONTP 51-1-85
ОНТП 51-1-85
|
|
National Engineering Design Standards. Trunk Pipelines. Part I: Gas Pipelines
Общесоюзные нормы технологического проектирования. Магистральные трубопроводы. Часть I. Газопроводы
Status: Not defined by law
Standards of technological design establish requirements for the design of technological facilities that are part of gas pipelines, mandatory for all ministries and departments, as well as organizations involved in the design of these facilities. Standards should be observed when designing new, expandable and reconstructed enterprises, buildings and structures of main gas pipelines that transport natural or associated petroleum gas with an excess pressure of 1.18 MPa (12 kgf
Нормы технологического проектирования устанавливают требования к проектированию технологических объектов, входящих в состав магистральных газопроводов, обязательные для всех министерств и ведомств, а также организаций, осуществляющих проектирование этих объектов. Нормы должны соблюдаться при проектировании новых, расширяемых и реконструируемых предприятий, зданий и сооружений магистральных газопроводов, по которым транспортируется природный или попутный нефтяной газ с избыточным давлением от 1,18 МПа (12 кгс/см2) до 9,81 МПа (100 кгс/см2) включительно (при одиночной прокладке и прокладке в техническом коридоре). При проектировании расширения или реконструкции действующих предприятий требования настоящих норм распространяются только на расширяемую или реконструируемую часть. Требования норм не распространяются на проектирование предприятий хранения и транспорта сжиженных газов, предприятий по добыче и хранению природного газа (головные сооружения, установки комплексной и предварительной подготовки газа, дожимные компрессорные станции), магистральные газопроводы, по которым транспортируется агрессивный к металлам газ (содержащий сероводород или пылевидные частицы серы).
Choose Language:
Format: Electronic (pdf/doc)
Approved: Mingazprom,
10/29/1985
SKU: RUSS147259
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Sectoral and departmental regulatory and methodological documents »
Design and construction of oil and gas industry facilities »
Standards for pipe fittings (TPA) »
8. Piping valves (TPA) design »
8.2 Calculations »
8.2.1 Strength calculations »
Standards for pipe fittings (TPA) »
3. Piping valves (TPA) standards for industries »
3.4 For pipeline transport of oil and gas »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
2003.200.13 Pipelines and their components »
The Document References:
GOST 12.1.009-76: Occupational safety standards system. Electrical safety. Terms and definitions
GOST 12.1.010-76: Explosion safety. General requirements
GOST 12.1.011-78: Explosive mixtures. Classification and test methods
GOST 12.3.002-75: Occupational safety standards system. Manufacturing processes. General safety requirements
GOST 12.4.026-76: Signal colors and safety signs
GOST 14202-69: Pipe-lines of industrial plants. Identification coloring, safety signs and marking screens
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 25812-83: Steel pipe mains. General requirements for corrosion protection
GOST 9.015-74: Unified system of corrosion and ageing protection. Underground constructions. General technical requirements
OST 51.63-80: Gas pipeline Linear part Terms and Definitions
PBVHP-74: Safety rules in explosive and explosive chemical and petrochemical industries
RD 39-22-113-78: Interim Regulation for Protection against Static Electricity in Process Facilities and Structures in the Oil and Gas Industries
SN 174-75: Instruction for industrial power supply design
SN 227-82: Guidelines for Standardized Design
SN 245-71: Sanitary standards for the design of industrial enterprises
SN 357-77: Design Guidelines for Industrial Electrical Equipment for Power and Illumination
SN 433-79: Guidelines for Construction Design for Oil and Gas Industry Facilities, Buildings, and Structures
SN 527-80: Instructions on Designing of Steel Process Piping, Рnom up to 10 MPa
SN 528-80: Specified list of physical quantity units to be used in architecture and construction
SNiP 2.01.01-82: Construction climatology and geophysics
SNiP II-12-77: Noise protection
SNiP II-90-81: Production buildings of industrial enterprises
VNTP 115-80: Wire Line Communications Facilities. Backbone Cable Lines
VSN 294-72: Instruction on installation of electrical equipment in plant with pipe risk: voltage up to 1000V
VSN 332-74: Manual on assembly of power and lighting networks electric equipment in explosion hazard zones
VSN 51-1-80: Guidelines for Construction Practices Within Safety Zones of Trunk Pipelines Administered by the Ministry of the Gas Industry
The Document is Referenced By:
RD 153-34.1-30.106-00: Rules for technical operation of gas-handling facilities for gas-turbine and combined-cycle units at thermal power plants
RD 153-39.0-112-2001: Method for the Determination of Specified Quantity Allowances for Natural Gas for Process Needs of a Trunk Gas Transport Pipeline
RD 34.30.106-95: Guidelines for the design of gas supply system with the addition of natural gas up to 0.5 MPa for gas turbine and combined cycle thermal power plants of RAO "UES of Russia", 08/24/95
RD 51-166-92: Temporary instruction on the accounting of gross emissions of nitrogen oxides and carbon at gas turbine compressor stations on the measured amount of fuel gas
VRD 39-1.10-006-2000*: Rules for the technical operation of gas pipelines
VRD 39-1.8-055-2002: Standard design specification for compressor stations (CS), booster compressor stations (BCS) and compressor stations of underground gas storage facilities (CS UGSF)
VSN 51-3-85: Design of field steel pipelines
|
Customers Who Viewed This Item Also Viewed:
 |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
High strength rolled steel. General specification
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
