RD 50-453-84
РД 50-453-84
|
|
Procedural Guidelines for Error Characteristics of Measuring Devices Under Actual Operating Conditions. Calculation Methods
Методические указания. Характеристики погрешности средств измерений в реальных условиях эксплуатации. Методы расчета
Status: Not effective - Canceled in the Russian Federation. Rosstandart order No. 1386 of June 11, 2019.
These guidelines set the methods for calculating the characteristics of the component of the error of direct single measurements - the error of the measuring instrument (SI) - according to the metrological characteristics of the SI, known characteristics of the influencing quantities and the input signal, normalized in accordance with GOST 8.009-84. Guidelines are intended for use in the development of normative-technical documents for the calculation of measurement error or the relevant sections of other normative-technical documents; in the development of measurement procedures, in particular, in the choice of measurement methods and measuring instruments that provide the specified norms of measurement accuracy.
Настоящие методические указания устанавливают методы расчета характеристик составляющей погрешности прямых однократных измерений - погрешности средства измерений (СИ) - по нормируемым в соответствии с ГОСТ 8.009-84 метрологическим характеристикам СИ, известным характеристикам влияющих величин и входного сигнала. Методические указания предназначены для использования при разработке нормативно-технических документов по расчету погрешности измерений или соответствующих разделов других нормативно-технических документов; при разработке методик выполнения измерений, в частности, при выборе методов измерений и СИ, обеспечивающих заданные нормы точности измерений.
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
2/8/1984
SKU: RUSS148336
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Regulatory documents of supervisory authorities »
Normative documents of Committee of Russian Federation for Standardization, Metrology and Certification »
PromExpert »
SECTION II. METROLOGICAL »
I Organizational and technical bases of metrological support »
1 Organization and management of metrological support »
1.1 Basic provisions of metrological support »
ISO classifier »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.020 Metrology and measurements in general »
National standards »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.020 Metrology and measurements in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
T General technical and organizational and methodological standards »
T8 State measurement system »
T80 Rules, norms, regulations infield of ensuring uniformity of measurements »
National Standards for OKSTU »
SYSTEMS OF GENERAL TECHNICAL AND ORGANIZATIONAL-METHODOLOGICAL STANDARDS »
State system for ensuring the uniformity of measurements (GSI) »
The Document References:
GOST 8.009-84: State system for ensuring the uniformity of measurements. Standardized metrological characteristics of measuring instruments
RD 50-148-79: Guidelines. Rationing and determination of the dynamic characteristics of analog-digital converters of instantaneous electrical voltage and current
The Document is Referenced By:
GOST 33435-2015: Control, monitoring and safety means of railway rolling stock. Safety requirements and control methods
GOST 34012-2016: Railway automatics and telemechanics equipment. General technical requirements
GOST 8.010-2013: State system for ensuring the uniformity of measurements. Procedures of measurements. Main principles
GOST R 50.05.16-2018: Conformity assessment system in the field of atomic energy use. Conformity assessment in the form of control. Unbrakable control. Metrological support
GOST R 54798-2011: Control, monitoring and safety means of railway rolling stock. Safety requirements and control methods
GOST R 55369-2012: Railway automatics and telemechanics equipment. General technical requirements
GOST R 8.563-2009: State system for ensuring the uniformity of measurements. Procedures of measurements
GOST R 8.563-96: State system for ensuring the uniformity of measurements. Procedures of measurements
GOST R 8.596-2002: State system for ensuring the uniformity of measurement. Metrological assurance for measuring system. Main principles.
GOST R 8.741-2011: State system for ensuring the uniformity of measurements. Volume of natural gaz. General requirements for measurement procedure
GOST R 8.741-2019: State system for ensuring the uniformity of measurements. The volume of natural gas. General requirements for measurement procedures
GOST R 8.932-2017: State system for ensuring the uniformity of measurements. Requirement to methodologies (to the methods) of measuring in area of uses of nuclear-power. Substantive provisions
GOST R 8.985-2020: State system for ensuring the uniformity of measurements. Standard Reference Service for the Use of Atomic Energy. General Provisions
MI 1317-2004: State system for ensuring uniformity of measurements. Results and characteristics of the measurement error. Forms of representation. Ways to use during testing of product samples and control over the parameters of product samples and control of their para
MI 1317-86: Guidelines. State system for ensuring uniformity of measurements. Results and characteristics of measurement error. Forms of representation. Methods of use when testing product samples and monitoring their parameters
MI 1552-86: State system for ensuring uniformity of measurements. Single straight measurements. Evaluation of measurement errors
MI 1698-87: Methodical instructions. Reliability assessment of data on the physical properties of polymeric materials
MI 1862-88: Guidelines. State system of measurement uniformity. Measuring channels of dispatching telecontrol systems of oil and gas production facilities. Typical methodology and program of metrological certification
MI 188-86: Guidelines. State system for ensuring uniformity of measurements. Means of measurement. Establishing the values of the parameters of calibration methods
MI 1967-89: Recommendation. State system for ensuring uniformity of measurements. The choice of methods and measuring instruments in the development of measurement techniques. General provisions
MI 2232-2000: State system for ensuring the uniformity of measurements. Ensuring the effect of measurements by the control of technological processes. Estimation of the measuring error when the limited point of information
MI 2240-98: National Measurement Standards. Analysis of Measurement, Inspection, and Testing Practicies at Businesses, Organizations, and Associations. Work Execution Technique and Procedures
MI 2267-2000: State system for ensuring the uniformity of measurements. Ensuring the effect of measurements by the control of technological processes. Metrological examination of technical documents
MI 2439-97: National system for measurements unification. The measuring system metrological characteristics. Notation. The principles of regulation, definition and control.
MI 2441-97: Tests for the approval of the measuring systems types. General requirements. Guidelines
MI 2500-98: National Measurement Standards. Basic Principles for Metrological Assurance for Small Businesses
MI 2539-99: GSE. Measuring channels of controllers, measuring and computing, control, software and hardware systems. General requirements for methods of verification
MI 2553-99: National Measurement Standards. Thermal Energy and Heat Transfer Agent in Piped Heat Supply Systems. Method for Assessment of Measurement Error. Basic Principles
MI 2731-2002: Recommendation. State system for ensuring uniformity of measurements. Oil flow rate of oil wells. Methods for performing measurements with the mass measurement installation of the type "ASMA"
MI 3592-17: Recommendation. State system for ensuring uniformity of measurements. Methods for determining the metrological characteristics of measuring instruments used in the field of atomic energy use
OST 45.150-99: Measurement Techniques. Order of development and certification
OST 95 10571-2002: Measurement system for the purpose of accounting and control of nuclear materials. Main provisions
PMG 92-2009: The metrological expert evaluation of interstate and national standarts projects
PR 32.131-98: Rules for Metrology. Typical training program for calibrators measuring instruments of geometric quantities in railway transport
PR 50.2.013-97: GSOEI. The procedure for accreditation of the metrological services of legal entities to the right of certification of measurement procedures and metrological examination of documents
R 50.2.038-2004: State system for ensuring the uniformity of measurements. Direct single measurements. Estimation of errors and uncertainty of measurements result
R 50-54-45-88: Recommendations. Calculations and tests of strength. Experimental methods for determining the stress-strain state of machine elements and structures. Method of full-scale tensometry of power equipment
R 52.14.648-2003: Recommendations. Metrological examination of regulatory and technical documentation
RD 34.09.113-90: Procedural Guidelines for Assessment of Accuracy in Determination of Specific Nominal Consumption of Fuel per Electric Power Generated by Power Units with Power of 300 MW and Above
RD 34.11.303-97: Procedural Guidelines. Development and Certification of Measurement Methods Used at Electric Power Facilities to Monitor Process Parameters not Subject to Government Metrological Inspection. Organization and Procedure
RD 34.11.332-97: Procedural Guidelines. Development and Certification of Measurement Methods Used at Electric Power Facilities in Areas Subject to Government Metrological Monitoring and Inspection. Organization and Procedure
RD 34.11.408-91: Model Program for Metrological Certification of Telemetry Channels of Operational Information Complex of Automated Dispatch Control System
RD 34.11.409-92: Standard Algorithms for Automated Processing of Experimental Data for Metrological Certification and Verification of Measurement Channels of Measurement Systems
RMG 62-2003: State system for ensuring the uniformity of measurements. Ensuring the effect of measurements by the control of technological processes. Estimation of the measuring error when the limited point of information
RMG 63-2003: State system for ensuring the uniformity of measurements. Providing measurement efficiency in control of technological processes. Metrological expertise of the technical documentation
SO 153-34.11.325-90: Procedural Guidelines for the Determination of Error in Measurement of Active Electric Power During Generation and Distribution
STB 1188-99: Drinking water. General requirements for the organization and quality control methods
|
Customers Who Viewed This Item Also Viewed:
 |
Industrial process measurement and control equipment. Reliability. General requirements and test methods
Language: English |
Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
Language: English |
System for ensuring the reliability and safety of construction sites. Loads and impacts. design standards
Language: English |
Heating, ventilation and air conditioning. Fire Safety Requirements
Language: English |
Reliability of atomic power stations and their equipment. General statements and reliability index nomenclature
Language: English |
Electromagnetic compatibility of technical equipment. Technical equipment for nuclear power plants. Requirement and test methods
Language: English |
Billets made of corrosion-resistant steels of 12Х18Н9Т, 12Х18Н10Т, 08Х18Н10Т, 10Х17Н13М2Т, 12Х18Н12Т and 03Х21Н32М3Б types.
Language: English |
Dependability in technics. Terms and definitions
Language: English |
System of products development and launching into manufacture. Technical assignment. Requirements to contents and form of presentation
Language: English |
Reliability in technology. Composition and general rules for setting reliability requirements
Language: English |
Stainless corrosion resisting, heat-resisting and creep resisting steel and alloy on iron-nickel-based products. Specifications
Language: English |
Natural gas for industrial and municipal purposes. Technical conditions
Language: English |
Global navigation satellite system. Emergency response system in case of accidents. Test methods for emergency services call device/system for compliance with the requirements for the quality of loudspeaker communication in the vehicle cab.
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
