GOST 23055-78
ГОСТ 23055-78
|
|
Non-destructive testing. Fusion welding of metals. Welds classification by radiography testing results
Контроль неразрушающий. Сварка металлов плавлением. Классификация сварных соединений по результатам радиографического контроля
Status: Effective. The limitation of the effectiveness period has been lifted: Protocol No. 3-93 of the IGU dated 03.03.93 (IUS 5-6-1993)
This standard applies to welded joints made by fusion welding of products from metals and their alloys with a thickness of welded elements from 1 to 400 mm and establishes seven classes of welded joints according to the maximum allowable pore sizes, slag, tungsten and oxide inclusions detected by radiographic control. The standard does not apply to welded joints of products subordinated to the USSR GosATOMENERGONADZOR and USSR Gosgortechnadzor.
Настоящий стандарт распространяется на сварные соединения, выполненные сваркой плавлением изделий из металлов и их сплавов с толщиной свариваемых элементов от 1 до 400 мм и устанавливает семь классов сварных соединений по максимальным допустимым размерам пор, шлаковых, вольфрамовых и окисных включений, выявляемых при радиографическом контроле. Стандарт не распространяется на сварные соединения изделий, подведомственных Госатомэнергонадзору СССР и Госгортехнадзору СССР.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstandart of the USSR,
4/7/1978
SKU: RUSS15775
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
25 Mechanical Engineering »
Welding regulations »
Welding work »
Welding regulations »
Defects »
Standards for pipe fittings (TPA) »
10. Production »
10.6 Non-destructive testing »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
1 Basic provisions of product testing and control system »
ISO classifier »
25 MECHANICAL ENGINEERING »
25.160 Welding, brazing and hard soldering »
25.160.40 Welds and welding »
National standards »
25 MECHANICAL ENGINEERING »
25.160 Welding, brazing and hard soldering »
25.160.40 Welds and welding »
National Standards for KGS (State Standards Classification) »
Latest edition »
V Metals and metal products »
V0 General rules and regulations on metallurgy »
V09 Test methods. Packaging. Marking »
National Standards for OKSTU »
SYSTEMS OF GENERAL TECHNICAL AND ORGANIZATIONAL-METHODOLOGICAL STANDARDS »
One-piece connections (welding, riveting, soldering, etc.) »
The Document References:
GOST 15467-79: Product quality control. Basic concepts. Terms and definitions
GOST 2601-84: Welding of metals. Terms and definitions of basic concepts
GOST 6636-69: Standard linear dimensions
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
The Document is Referenced By:
Decision 162: On the list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis ensures compliance with the requirements of the technical regulations of the Eurasian Economic Union "On requirements for main pipelines for the transportation of liquid and gaseous hydrocarbons (TR EAEU 049/2020), and the list of international and regional (interstate) standards, and in their absence - national (state) standards that contain rules and methods of research (tests) and measurements, including sampling rules necessary for the application and implementation of the requirements of technical regulation of the Eurasian Economic Union "On requirements for pipelines for the transportation of liquid and gaseous hydrocarbons (TR EAEU 049/2020) and conformity assessment of technical regulation objects
GOST 11004-84: Principal ventilation mine blowers
GOST 17032-2022: Horizontal steel tanks for petroleum products. Specifications
GOST 20426-82: Radiation methods of defectoscopy
GOST 21561-2017: Automobile tanks for hydrocarbon gas transportation at pressure up to 1,8 MPa. Technical requirements and test methods
GOST 21561-76: Automobile tanks for liquefied hydrocarbon gas transportation at pressure up to 1,8 MPa. General specifications
GOST 31385-2008: Vertical cylindrical steel tanks for oil and oil-products. General specifications
GOST 31385-2016: Vertical cylindrical steel tanks for oil and oil-products. General specifications
GOST 32569-2013: Steel pipe technology. Requirements for design and operation of explosive and chemically dangerous production
GOST 33259-2015: Flanges for valves, fittings and pipelines for pressure to PN 250. Design, dimensions and general technical requirements
GOST 33752-2017: Steel welded cylinders for liquefied hydrocarbon gas, used as motor fuel on automotive vehicle. Specifications
GOST 33857-2016: Pipe fittings. Welding and quality control of welded joints. Technical requirements
GOST 34347-2017: Steel welded vessels and apparatus. General technical conditions
GOST R 50599-93: Welded steel vessels and apparatus under high pressure. Non-destructive control while the manufacturing and operating
GOST R 50608-93: Refrigerating equipment. Steel apparatus. Welded joints. Technical requirements and checking methods
GOST R 52630-2006: Steel welded vessels and apparatus. General specifications
GOST R 52630-2012: Steel welded vessels and apparatus. General specifications.
GOST R 52910-2008: Vertical cylindrical steel tanks for oil and oil-products. General specifications
GOST R 54803-2011: High-pressure welded steel vessels. General technical requirements
GOST R 55085-2012: Cylinders steel welded on pressure 1,6 MPа for liquefied hydrocarbon gas, used as motor fuel on car transport facility. Specifications
GOST R 55850-2013: Petroleum and natural gas industries. Progressing cavity pump systems for artificial lift. Part 2. Surface-drive systems. General technical requirements
GOST R 58623-2019: The main pipeline transport of oil and oil products. Vertical cylindrical steel tanks. Technical Operation Rules
ITN 93: Instructions for technical supervision, methods of audit and rejection of tube furnaces, tanks, vessels and apparatuses of oil refining and petrochemical industries
ITNJe-93: Instruction on technical supervision and operation of pressure vessels not covered by the Rules of Gosgortechnadzor
Order 5214: The list of documents in the field of standardization, the application of which on a voluntary basis to ensure compliance with the requirements of application and execution of the Government of the Russian Federation of October 29, 2010 № 870 "On approval of technical regulations on the safety of gas distribution and gas consumption networks" (as amended on June 23, 2011) and implementation of conformity assessment
Order 5214: On approval of the List of documents in the field of standardization, the application of which on a voluntary basis to ensure compliance with the requirements of technical regulations "On safety of gas distribution and gas consumption networks" approved by the Government of the Russian Federation on October 29, 2010 N 870 (as amended on April 22, 2013) (lost force from 01.04.2022 on the order of Rosstandart from 10.01.2022 N 3)
OST 24.200.02-91: Assembling units of steel pipelines on nominal pressure<=10 MPa (100 kgf/cm2) of complete technological lines. General specifications.
OST 24.201.03-90: Steel high-pressure vessels and devices. General technical requirements.
OST 26.260.18-2004: Process modules for oil and gas industry. General technical specifications
OST 26.260.758-2003: Metal structures. General technical requirements.
OST 26-01-1434-87: Welding of steel technological pipelines on nominal pressure over 10 to 100 MPa (over 100 to 1000 kgf/cm2). Technical requirements.
OST 26-01-151-82: Steel welded vessels and devices for low-temperature gas separations. Technical requirements, acceptance regulations and testing methods.
OST 26-07-2071-87: Pipeline fittings from steel resistant to sulphide corrosion cracking. General specifications.
OST 26-18-5-88: Technological units of gas and oil industry. General technical requirements.
OST 26-291-94: Steel welded vessels and devices. General technical requirements.
OST 36-58-81: Steel building structures. Welding. Basic requirements.
OTU 3-01: Vessels and apparatuses. General specifications for the repair of buildings
PB 03-108-96: Process pipeline design and safe operation rules
PB 03-381-00: Regulations of installation of vertical cylindrical steel reservoirs (steel scroll tanks) for petroleum and petroleum products
PB 03-384-00: Rules for design, manufacture and acceptance of steel welded vessels and apparatus
RD 153-39.1-059-00: Technique of technical diagnostics of gas control points
RD 153-39.4-078-01: Operation Requirements for Tanks on Trunk Petroleum Product Pipelines and at Petroleum Depots
RD 22-207-88: Lifting machines. General requirements and production standards
RD 24.020.11-93: Welded joints of stationary steam, gas and hydraulic turbines. Testing rules and quality evaluation standards.
RD 24.207.02-90: Welding of fitting to pipeline. Technical requirements.
RD 26.260.010-2002: The leading document on standardization. The list of standard documentation on standardization on the cells and devices working under pressure.
RD 26.260.010-97: List of Regulatory Documents on Standardization for Pressure Vessels and Apparatus
RD 26-02-80-2004: The leading document. Welded coils for pipe furnaces. Requirements to design, production and delivery.
RD 2-97: Regulations on the system for the technical diagnosis of autoclaves in the production of building materials
RD 31.3.3-97: Guidelines on technical control of waterworks in maritime transport. Ministry of Transport, DMT Soyuzmorniiproekt, 1997
RD 34.17.427-89: Procedural Guidelines. Nondestructive Testing at Thermal Power Stations. General Requirements
RD 38.13.004-86: Operation and repairs of process pipelines operating under pressure up to 10.0 MPa (100 kgf/cm2)
RD OP.42-001-85: Main provisions for welding and control of the NPP tanks (reservoirs)
RD ROSEK-01-002-96: Hoisting machines. Metal structures. Radiation control. Key Points
RDI 26-15-80: Instructions for making inner vessels of isothermal tanks for liquefied carbon dioxide
RTM 36.2-87: Guide to the Use of Photographic Paper and Magnifying Screens for Quality Control of Welded Joints in Organizations Administered by USSR Minmontzhspetststroy
SA 03-005-07: Industrial pipelines of oil-refining, petrochemical and chemical industry. Requirements to configuration and operation
Safety Guide: Recommendations on arrangement and safe operation of process pipelines
Safety Guide: Recommendations on technical diagnostics of welded vertical cylindrical tanks for oil and petroleum products
SNiP 3.05.03-85: Heat networks
SNiP 3.06.07-86: Bridges and Pipes. Rules for Inspection and Testing
SNiP 42-01-2002: State committee of Russian Federation for construction and residential-utility complex (GOSSTROY OF Russia)
SP 129.13330.2019: External networks and water supply and sewerage facilities
SP 365.1325800.2017: Vertical cylindrical steel tanks for storage of oil products. Rules of work's production and acceptance under installation
SP 42-102-2004: Design and construction of gas pipelines from metal pipes. To replace SP 42-102-96
SP 74.13330.2023: Heat networks.
ST TsKBA 013-2007: Pipe fittings. Welding of fittings to the pipeline. Technical requirements
ST TsKBA 025-2006: Pipe fittings. Welding and quality control of welded joints. Technical requirements
ST TsKBA 052-2008: Pipe fittings. Requirements for materials of fittings used for hydrogen sulfide environments
ST TsKBA 089-2010: Pipe fittings. Welding defects castings. Technical requirements
STB 1428-2003: Non-destructive testing. Welded connections of pipes and steel structures. Radiographic method
STO-SA-03-002-2009: Rules for the design, manufacture and installation of vertical cylindrical steel tanks for oil and oil products
TU 102-488-95: Connecting parts and nodes of trunk pipelines on RR up to 10 MPa (100 kgf / cm2)
TU 3615-018-00217320-2006: Spherical tanks. Technical specifications
TU 3615-132-00220302-2008: Ball tanks for liquefied petroleum gases. Specifications
TU 36-26-11-4-89: Steel building construction, vertical cylindrical tanks for oil and petroleum products with a volume of 100 to 50,000 m3. Technical conditions
VSN 362-87: Disinfections and Etching of Pipelines
VSN 427-81: Guidelines for Welding Structural Steel Using Welding Wire PPB-5
|
Customers Who Viewed This Item Also Viewed:
 |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
High strength rolled steel. General specification
Language: English |
Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads
Language: English |
Articulated connector devices with cast male and female parts for freight cars of articulated type. General technical specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
