GOST 6370-83
ГОСТ 6370-83
|
|
Petroleum, petroleum products and additives Methods for determination of mechanical admixtures
Нефть, нефтепродукты и присадки. Метод определения механических примесей.
Status: Not effective - Superseded. Registration information 666-st from 09/27/2018 (official site of Rosstandart)
The standard applies to oil, liquid petroleum products and additives, and establishes a method for determining mechanical impurities. The standard does not apply to greases and bitumens. The essence of the method consists in filtering the tested products with preliminary dissolution of slowly filtered products in gasoline or toluene, washing the precipitate on the filter with a solvent, followed by drying and weighing.
Стандарт распространяется на нефть, жидкие нефтепродукты и присадки и устанавливает метод определения механических примесей. Стандарт не распространяется на пластичные смазки и битумы. Сущность метода заключается в фильтровании испытуемых продуктов с предварительным растворением медленно фильтрующихся продуктов в бензине или толуоле, промывании осадка на фильтре растворителем с последующим высушиванием и взвешиванием.
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
4/12/1983
SKU: RUSS15778
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
75 Extraction and processing of oil, gas and related production »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
030/2012 TR CU. On requirements for lubricants, oils and special fluids »
Regulations and standards (to 030/2012 TR CU) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.9 Testing and control of chemical and industrial products »
4.9.9 Petroleum products of industrial and domestic consumption, lubricating oils and greases, plastic »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.2 Testing and control of products of fuel and energy industry »
4.2.2 Oil, oil products and gas »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.080 Petroleum products in general »
National standards »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.080 Petroleum products in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
B Oil products »
B0 General rules and regulations for oil refining industry »
B09 Test methods. Packaging. Marking »
National Standards for OKSTU »
OIL, PETROLEUM PRODUCTS, GAS »
Control methods (testing, analysis, measurements) »
The Document is Replaced With:
GOST 6370-2018: Petroleum, petroleum products and additives. Method for determination of mechanical admixtures
As a Replacement Of:
GOST 6370-59: Petroleum products and additives. Method for the determination of mechanical impurities
The Document References:
GOST 12026-76: Filter paper for laboratory application
GOST 1277-75: Reagents. Silver nitrate. Specifications
GOST 14710-78: Petroleum toluene
GOST 18300-87: Technical rectified ethyl alcohol. Specifications
GOST 25336-82: Laboratory glassware and equipment. Basic parameters and dimensions
GOST 28498-90: Liquid-in-glass thermometers
GOST 33-2000: Petroleum products. Transparent and opaque liquids. Determination of kinematic viscosity and calculation of dynamic viscosity
GOST 5789-78: Reagents. Toluene. Specifications
GOST 6709-72: Distilled water. Specifications
GOST 8505-80: Nefras-C 50/170. Specifications
GOST 9147-80: Laboratory porcelain ware and apparatus. Specifications
The Document is Referenced By:
FR 1.29.2009.06689: Recommendation. State system for ensuring uniformity of measurements. Mass and volume of petroleum products. Measurement procedure in vertical tanks
GOST 10121-76: Selectively purified transformer oil
GOST 10289-2022: Oil for marine gas turbines. Specifications
GOST 10289-79: Oil for marine gas turbines
GOST 10363-78: Oil ЭШ for hydraulic systems of high-load mechanisms. Specifications
GOST 10433-75: Fuel oil for gas-turbine plants. Specifications
GOST 10534-78: Sulphonated additive CБ-3. Specifications
GOST 10541-78: Automobile motor oils for carburetor engines
GOST 10585-2013: Petroleum fuel. Mazut. Specifications
GOST 10585-75: Black oil fuel
GOST 10585-99: Oil fuel. Mazut. Specifications
GOST 10957-74: Siliconorganic liquids 132-24 and 132-25. Specifications
GOST 11122-84: Hinge oil BНИИ НП-25. Specifications
GOST 12261-87: Afk additive
GOST 12337-84: Motor oils for diesel engines
GOST 12672-77: Oil for rolling mills ПС-28. Technical specifications
GOST 12869-77: Electrical insulating synthetic fluid octol. Specifications
GOST 13004-77: Polyethylsiloxane fluids. Specifications
GOST 13076-86: Synthetic oil BНИИ НП 50-1-4ф. Specifications
GOST 13374-86: Instrument oil ВНИИ НП-1-ЧМО. Specifications
GOST 14298-79: Oil fuel for open-hearth furnaces. Specifications
GOST 15171-78: Additive АКОР-1. Specifications
GOST 15819-85: Oils РМ and РМЦ. Specifications
GOST 16422-79: Transmission grease ЦИАТИМ-208. Specifications
GOST 1667-68: Motor fuel for medium- and low-speed diesel engines
GOST 16728-78: Oil ВНИИ НП-403. Specifications
GOST 17108-86: Positive-displacement hydraulic drive and lubricating systems. Methods of parameters measurement
GOST 17601-90: Marine centrifugal separators. Acceptance and methods of tests
GOST 1805-76: Apparatus oil МВП. Specifications
GOST 18499-73: Kerosene for technical purposes. Specification
GOST 18613-88: Hydraulic fluid of grades 132-10 and 132-10Д. Specifications
GOST 1861-73: Compressor oils
GOST 20799-2022: Industrial oils. Technical conditions
GOST 20799-75: Industrial oils. Specifications
GOST 20799-88: Industrial oils Specifications
GOST 20944-75: Liquids for aircrafts systems. Method for determination thermo oxidizing stability and corrosion activity
GOST 20991-75: Motor oils. Method of testing their tendency to form deposits at high temperatures
GOST 20994-75: Motor oils. Method of testing their tendency to form deposits at low temperatures
GOST 21046-2015: Used petroleum products. General specification
GOST 21046-86: Waste petroleum products
GOST 21532-76: Horological lubricant PS-1. Specifications
GOST 21743-76: Aviation oils
GOST 21748-76: Oil MЗ-52. Specifications
GOST 21791-2022: Synthetic oil MAS-30NK. Specifications
GOST 21791-76: Мac-30nk synthetic oil
GOST 23008-78: Shock absorber liquid AЖ-12т. Specifications
GOST 23497-79: Motor oils M-14B23 and M-20B2. Specifications
GOST 23639-79: Additive KP
GOST 23652-79: Transmission oils
GOST 23683-89: Hard petroleum paraffines
GOST 24869-98: Industrial cleanliness. General
GOST 2488-79: Ceresin. Specifications
GOST 25149-82: The liquid N7. Specifications
GOST 25476-82: Hydraulic fluid power and lubricating systems. Filters. Acceptance and Test methods
GOST 25770-83: High-speed diesel engine motor oils for transport vehicles
GOST 26378.2-2015: Used petroleum products. Method for determination of mechanical impurities and contaminants
GOST 26378.2-84: Used petroleum products. Method for determination of mechanical impurities and contaminant
GOST 305-82: Diesel fuel. Specifications
GOST 31378-2009: Oil. General specifications.
GOST 32-74: Turbine oils
GOST 3276-89: Lubricating grease ГОИ-54п. Specifications
GOST 3582-84: Medical vaseline. Specifications
GOST 3677-76: Ceresin composition. Specifications
GOST 4113-80: Preventive composition ПП 95/5. Specifications
GOST 4225-76: Perfume oil. Specifications
GOST 5546-86: Oils for refrigerating machines
GOST 5774-76: Condenser vaselin. Technical requirements
GOST 5775-85: Capacitor oil
GOST 610-2017: Axle oils. Technical conditions
GOST 610-72: Oils for axle journals. Specifications
GOST 6360-83: MT-16P and M-16PC oils.
GOST 6411-76: Heavy cylinder oils
GOST 6457-66: Oils МК-8. Specifications
GOST 7658-74: Synthetic high-melting ceresin. Specifications
GOST 7935-74: General-purpose homological oils. Specifications
GOST 7936-76: Thickened clock oil PS-4
GOST 8.587-2019: State system for ensuring the uniformity of measurements. The mass of oil and petroleum products. Measurement procedures (methods)
GOST 8.589-2007: State system for ensuring the uniformity of measurements. Conducting registration operations on items of reception-delivery of oil in the petrowire systems
GOST 8463-76: Oil С-220. Specifications
GOST 8551-74: Grease ЦИАТИМ-205. Specifications
GOST 8581-78: Motor oil for automobile and tractor
GOST 8781-71: Low-temperature clock oils. Specifications
GOST 9243-75: KS-19 compressor oil
GOST 982-80: Transformer oils
GOST 9965-76: Petroleum for oil-processing plants. Specifications
GOST 9972-74: Petroleum turbine oils with additives
GOST R 50558-93: Industrial purity. Lubricating and cooling liquids. Specifications
GOST R 50559-93: Industrial purity. General requirements for supplying, transporting, storage and feeding of working liquids
GOST R 51559-2022: Power oil transformers of 110 and 220 kV voltage classes and autotransformers of 27,5 kV voltage class for AC traction railway power supply systems. General specifications
GOST R 51858-2002: Crude petroleum. General specifications
GOST R 51907-2002: Motor oil for marine diesels М-20Г2СД. Specifications
GOST R 52755-2007: Liquid composite fuel. Specifications
GOST R 54331-2011: Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear. Specifications
GOST R 54389-2011: Stable gas condensate. Specifications
GOST R 55775-2013: Aviation oil МС-8П. Specifications
GOST R 57659-2017: The railway transport objects testing methods of prolongation operating cycle. Part 1. Power transformers and auto transformers for railway power substations, transform substations and power supply linear devices
GOST R 58115-2018: Converter transformers for voltages from 6 to 110 kV for railway traction substations. General specifications
GOST R 70708-2023: Pyrolysis liquid products. Pyrolysis light tar. Technical conditions
GOST R 8.595-2004: State system for ensuring the uniformity of measurements. Mass of petroleum and petroleum products. General requirements for procedures of measurements
GOST R 8.615-2005: State system for ensuring the uniformity of measurements. The measuring of quantity of taken from bowels oil and oil gas. General metrological and technical requirements
GOST R 8.786-2012: State system for ensuring the uniformity of measurements. Fuel oil mass. Measurement procedure in horizontal storage tanks by indirect method of static measurements. General metrological requirements
GOST R 8.787-2012: State system for ensuring the uniformity of measurements. Mass of mazut. Measurement of the fuel oil mass in railway tanks. General metrological requirements
GOST R 8.903-2015: State system for ensuring the uniformity of measurements. Mass of petroleum and petroleum products. Procedures of measurements
ITS 50-2017: Processing of natural and accompanying gas
Manual: Manual for impulse and low consumption fire extinguishing systems
MI 2418-97: State system for ensuring uniformity of measurements. Classification and application of technical means for testing oil and petroleum products
MI 2693-2001: Crude Oil Metering Oil Production Facilities
MI 2735-2002: Recommendation. GSE. A lot of oil. Methods for measuring the system of measuring the quantity and quality of oil UUN NSP "Sergeevka" NGDU "Ufaneft"
MI 2837-2003: Oil hand-over and acceptance points metrological and technical support
MI 2950-2005: Recommendation. State system for ensuring uniformity of measurements. A lot of oil. Methods for performing measurements in horizontal tanks in the system of the main pipeline transport
MI 2951-2005: State system for ensuring uniformity of measurements. Crude oil mass. Methods of measurement in vertical tanks in the system of main pipeline transport
MI 2952-2005: State system for ensuring uniformity of measurements. Crude oil mass. Methods of measurement in railway tanks in the system of main pipeline transport
MI 2953-2005: State system for ensuring uniformity of measurements. Crude oil mass. Methods of measurement in automobile tanks in the system of the main oil pipeline transport
MI 2972-2006: State system of measuring uniformity provision. Petroleum mass. Method of measuring by the system of petroleum quantity and properties measuring system No.1005 JSC ´Shugurovskiy petrochemical plant´
MI 2975-2006: State system of measuring uniformity provision. Petroleum mass. Indirect measuring method of dynamic measurements on the registration point pump station 'Suslovo' JSC 'Uraltransnefteproduct'
MI 3200-2009: Recommendation. GSE. Mass of crude oil. Methods of measuring the system of measuring the amount and parameters of crude oil at the temporary loading point of the Bayandy field at the Chamber of Commerce and Industry Usinskneftegaz OOO Lukoil-Komi
MI 3241-2009: Recommendation. State system for ensuring uniformity of measurements. Mass and volume of petroleum products. Measurement technique indirect method of dynamic measurements
MI 3301-2010: Recommendation. State system for ensuring uniformity of measurements. Oil product pipeline. Acceptance points of petroleum products. Metrological and technical support
MI 3342-11: Recommendation. GSE. Requirements for testing laboratories that monitor the quality of oil
MI 3532-2015: State system for ensuring the uniformity of measurements. Recommendations on definition of weight of oil at registration operations with application quantity measures and indicators of oil quality
NA.GNMC.0293-19 MP: Instruction. State system for ensuring the uniformity of measurements. The system for measuring the quantity and indicators of oil at the PSP "Komsomolsky", LLC "RN-Sakhalinmorneftegaz". Verification method
OST 153-39.2-048-2003: Oil. Crude oil. Routine research of reservoir fluids and separated oil. Scope of research and presentation of results.
OST 38.01445-88: Lubrication and cooling liquid MR-7. Technical conditions
OST 51.65-80: Stable gas condensate. Technical conditions.
PUE: Electrical Installation Rules (PUE). Chapter 1.1 General (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.2 Electricity supply and electrical networks (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.7 Grounding and Electrical Safety Precautions (Seven Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.9 Insulation of electrical installations (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.6 Electric Welding Machines (Seven Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.10. Electrolysis Plants and Plating Plants (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.8. Acceptance Test Standards (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.1. Switchgears up to 1 kV AC and up to 1.5 kV DC (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.1. General part (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.2. Electricity supply and electrical networks (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.3. Selection of conductors by heating, economic current density and by corona conditions (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.4. Selection of electrical devices and conductors for short circuit conditions (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.5. Electricity metering (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.6. Electrical Measurements (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.7. Grounding and Electrical Safety Precautions (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.1. Electrical Wiring (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.2. Busducts up to 35 kV (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.3. Cable lines with voltage up to 220 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.4. Overhead power lines with voltage up to 1 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.5. Overhead power lines with voltage above 1 kV (Beginning) (with Amendments and additions) (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.1. Protection of electrical networks with voltage up to 1 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.2. Relay Protection (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.3. Automation and telemechanics (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.4. Secondary Circuits (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.2. Switchgears and substations with voltages above 1 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.3. Converter substations and installations (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.4. Battery Units (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.1. Electrical machine rooms (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.2. Generators and Synchronous Compensators (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.3. Electric motors and their switching devices (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.4. Crane Electrical Equipment (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.5. Elevator Electrical Equipment (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.6. Condensing Units (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.1. General part (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.1. Electrical equipment of residential, public, administrative and domestic buildings (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.2. Interior lighting (seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.3. Outdoor lighting (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.4. Advertising Lighting (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.5. Lighting fixtures, installation devices (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.2. Electrical installations of entertainment enterprises, clubs and sports facilities (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.3. Electrical Installations in Hazardous Areas (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.4. Electrical Installations in Fire Hazardous Zones (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.5. Electrothermal Plants (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.6. Electric welding machines (sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.7. Peat electrical installations (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.5. Overhead power lines with voltages above 1 kV (End) (Sixth edition)
PUE: Electrical Installation Rules (PUE). Applications
PUE: Electrical Installation Rules (PUE). Chapter 6.6. Lighting devices and wiring devices (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.1. General part (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.2. Interior lighting (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.3. Outdoor Lighting (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.4. Advertising Lighting (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.5. Lighting fixtures, installation devices (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.1. Electrical Equipment for Residential and Public Buildings (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.2. Electrical equipment for entertainment enterprises, clubs and sports facilities (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.4. Overhead power lines with voltage up to 1 kV (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.5. Overhead power lines with voltage above 1 kV (Seventh edition) (with Amendment)
PUE: Electrical Installation Rules (PUE). Chapter 4.1. Switchgears up to 1 kV AC and up to 1.5 kV DC (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.2. Switchgears and substations with voltages above 1 kV (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.8. Acceptance test standards (Seventh edition)
R 50.2.040-2004: Metrological assurance of oil accounting when transferring via main pipeline system. Basic provisions
RB-136-17: Safety Guide for the Use of Atomic Energy
RD 153-34.0-04.202-98: Procedural Guidelines. Certification of Departments of Energy Facilities Performing Quantitative Chemical Analysis. Organization and Procedure
RD 153-34.0-44.221-2000: Guidelines for Quality Control of Diesel Fuel at Thermal Power Stations During Acceptance, Storage, and Use of it as Main, Backup, or Start-Stop Fuel in Gas Turbine and Steam-Gas Units
RD 153-34.1-40.504-00: Procedural Guidelines for Optimal Corrosion Protection of Storage Tanks and Protection of the Water in Them Against Aeration
RD 153-34.1-43.106-2001: Model Guidelines for Acceptance, Storage, and Use of Fireresistant Turbine Oils Type OMTI
RD 153-39-011-97: Instruction on accounting of oil products on trunk oil-products pipelines.
RD 212.0182-02: Manual for technical operation of inland waterway vessels
RD 31.1.02-04: Rules of technical operation of lifting and transport equipment of sea trading ports
RD 31.44.01-97: Rules of technical operation of lifting and transport equipment of sea trading ports
RD 34.01.203: Model Index of Operations Documentation for Chemical Shop of a Thermal Power Station
RD 34.09.604-89: Model Guidelines for Organization of Collection and Rational Use of Used Petroleum Products at Thermal and Hydroelectric Generating Stations, Electrical Networks, and Repair Facilities Administered by Minenergo USSR
RD 34.10.411-89: Ethanol consumption rates for organizations and enterprises of the USSR Ministry of Energy. Part 2
RD 34.10.558-84: Guidelines for the calculation of temporary flow rates of working fluids for hydraulic systems of construction vehicles operated by the USSR Ministry of Energy
RD 34.21.525: Procedural Guidelines for Cleaning Bottom Deposits from Fuel Oil Tanks
RD 34.43.102-96: Guidelines for Use of Petroleum-Based Turbine Oils
RD 34.43.105-89: Procedural Guidelines for Use of Transformer Oils
RD 34.43.301: Guidelines for Collection, Storage, and Rational Use of Used Oils in Construction Organizations Administered by Minenergo USSR
RD 34.44.215-96: Methods for the Determination of Quality of Water-Fuel Oil Emulsions Used n the Form of Liquid Boiler Fuel
RD 34.45-51.300-97: Electrical equipment testing scope and standards.
RD 39-1-1261-85: Technological regulations on the use of demulsifiers in oil preparation processes
RD 39-3-944-83: Standard provision for a laboratory that performs oil analyzes during acceptance operations and produced water
RD 39-5-649-81: Rules of industrial commissioning of petroleum quantity measuring systems
RMG 100-2010: State system for ensuring the uniformity of measurements. Recommendations about definition of weight of oil at registration operations with application quantity measures and indicators of quality of oil
RMG 85-2009: National Measurement Assurance System. Mass of oil. Methods of measurement in railway tanks in the system of main oil pipeline transport. The main provisions
RMG 86-2009: State system for ensuring the uniformity of measurements. Mass of petroleum. Measurement procedure in vertical tanks in the main petrowire systems. Basic propositions
RMG 87-2009: National Measurement Assurance System. Mass of oil. Methods of measurement in horizontal tanks in the system of main oil pipeline transport. The main provisions
RMG 88-2009: National Measurement Assurance System. Mass of oil. Methods of measurement in motorcar tanks in the system of main oil pipeline transport. The main provisions
RMG 94-2009: State system for ensuring the uniformity of measurements. Test laboratories performing of the quality control of oil at acceptance operations. Basic requirements
ST RK 2467-2014: Oil for hydrostatic transmissions MGE-46V. Specifications.
ST RK 2468-2014: Hydraulic oil AUP. Specifications.
ST RK 2470-2014: All-seasons hydraulic oil (VMGZ) Specifications.
ST RK 2471-2014: Motor oils All Season universal categories sf, sj, sl, sm, sn, cf-4, cg-4, ch-4, cl-4, cj-4 api. Specifications.
ST RK 2472-2014: Oils for automatic transmission systems. Specifications.
ST RK 2473-2014: Multigrade oil for mechanical transmission systems Category gl-4, gl-5. Specifications.
STO: Thermal power plants. Methods of assessing the condition of the main equipment
TU 0253-053-00151911-2008: Industrial oils
TU 34-38-20121-87: Oil inlets. General technical conditions for major repairs
TU 38.1011299-2006: IPM 10 aviation oil
TU 38.101821-2001: Turbine oil TP-22C. Technical conditions
TU 38.101821-2013: Turbine oil Тп-22С brand 1. Specifications
TU 38-101821-83: Turbine oil TP-22C. Technical conditions
TU 38-101937-83: Oil softener for the rubber industry
TU 39-1435-89: Oil for transportation to consumers. Technical conditions
VRD 39-1.10-064-2002: Equipment for liquefied natural gas (LNG). General technological requirements when operating storage, transportation and gasification
Customers Who Viewed This Item Also Viewed:
 |
Jet fuels
Language: English |
State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 5. Measurement procedure
Language: English |
Molded parts of coupler and automatic coupler devices of railway rolling stock. General specifications.
Language: English |
Main-line diesel locomotives. General technical requirements.
Language: English |
Four-wheel bogies of freight cars for mainline railways gauge 1520 (1524) mm. Specifications
Language: English |
Technical ethylcellosolve. Specifications
Language: English |
Automatic coupler model SA-3 and its components. Design and dimensions
Language: English |
Railway rolling stock. Devices to prevent running gear parts from dropping to the track. Methods of controlling strength characteristics
Language: English |
Electric heating devices for heating rolling stock railways. Safety requirements and test methods
Language: English |
Ice cream. General technical requirements
Language: English |
Welded joints in steel structures of railway rolling stock. Requirements for design, implementation and quality control
Language: English |
Locomotives The method of dynamic strength tests
Language: English |
Pipe fittings. Ball valves made of brass. General specifications
Language: English |
Railway rolling stock. Norms for permissible exposure of railway track and test methods
Language: English |
Locomotives. Requirements for strength and dynamic qualities
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.