Process automation systems. Design of electrical and pipe wiring. Part 3. Guidelines for the implementation of the documentation. Allowance for RTM 36.22.7-92
Системы автоматизации технологических процессов. Проектирование электрических и трубных проводок. Часть 2. Трубные проводки
Status: Effective
This manual contains technical requirements for pipe wiring automation systems and the basic provisions for their design, as well as recommendations on the choice of pipe wiring, valves, connecting and connecting devices. The document applies to the pipe wiring of automation systems in accordance with the scope of SNiP 3.05.07 and RTM 36.22.7. The document does not apply to automatic fire extinguishing systems and smoke removal.
Настоящее пособие содержит технические требования к трубным проводкам систем автоматизации и основные положения по их проектированию, а также рекомендации по выбору трубных проводок, арматуры, соединительных и присоединительных устройств. Документ распространяется на трубные проводки систем автоматизации в соответствии с областью распространения СНиП 3.05.07 и РТМ 36.22.7. Документ не распространяется на автоматику систем пожаротушения и дымоудаления
Choose Language:
Format: Electronic (pdf/doc)
Approved: GPKI Projectmountingautomatics,
6/1/1992
SKU: RUSS166900
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Sectoral and departmental regulatory and methodological documents »
Installation and special construction works »
PromExpert »
SECTION I. TECHNICAL REGULATION »
III Quality »
2 Product quality assurance »
2.1 Ensuring product quality at stage of technical preparation of production »
2.1.3 Automation of production management »
ISO classifier »
25 MECHANICAL ENGINEERING »
25.040 Industrial automated systems »
25.040.01 Industrial automation systems in general »
ISO classifier »
29 ELECTRICAL ENGINEERING »
29.060 Electrical Wires and Cables »
29.060.01 Electrical wires and cables in general »
ISO classifier »
91 CONSTRUCTION MATERIALS AND CONSTRUCTION »
91.140 Installations in buildings »
91.140.50 Power supply systems »
The Document References:
GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.1.007-76: Noxious substances. Classification and general safety requirements
GOST 12.1.010-76: Explosion safety. General requirements
GOST 12.2.060-81: Acetylene pipelines
GOST 1508-78: Control rubber and plastic-insulated cables. Specifications
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 16337-77: High-pressure polyethylene. Specifications
GOST 16377-70: Die blocks of sizing dies with rear location of guide posts. Construction and dimensions
GOST 18475-82: Cold-worked aluminum and aluminum alloy pipes
GOST 18599-2001: Polyethylene pressure pipes. Specifications
GOST 18599-83: Polyethylene pressure pipes
GOST 2.004-88: Unified system for design documentation. General requirements for performing design and technological documentation on printing and graphical output devices of computers
GOST 2.301-68: Unified system for design documentation. Formats
GOST 2.302-68: Unified system for design documentation. Scales
GOST 2.303-68: Unified system for design documentation. Lines
GOST 2.701-84: Unified system design documentation. Diagrams. Kinds and types. General requirements for fulfilment
GOST 2.702-75: Unified system for design documentation. Rules for presentation of electric layouts
GOST 2.709-89: Unified system of design documentation. Conventions of wires and terminal connections of electrical elements, equipment and circuits sections in circuit diagrams
GOST 2.721-74: Unified system for design documentation. Graphical designations in schemes. Graphical symbols of general use
GOST 21.401-88: System of design document for construction. Production technology. Main requirements to working drawings.
GOST 21.404-85: System of design documents for construction. Industrial process automation. Instrumentation symbols for use in diagrams
GOST 21.513-83: System of building documents. Anticorrosive protection of building structures. Working drawings
GOST 21.614-88: System of design documents for construction. Graphic symbols of electrical equipment and wiring on plans
GOST 3262-75: Water-supply and gas-supply steel pipes Technical conditions
GOST 356-80: Valves and details for piping. Pressures conditional, test and operational. Lines.
GOST 617-2006: General-purpose copper and brass tubes of round section. Specifications
GOST 8734-75: Seamless steel tubes cold deformed. Range
GOST 8943-75: Fittings from malleable cast iron with parallel thread for pipelines
GOST 8965-75: Connecting parts made of steel, with parallel thread, for pipelines of pressure p = 1.6 мpа
GOST 9941-81: Seamless cold- and warm-deformed tubes made from corrosion-resistant steel
SN 527-80: Instructions on Designing of Steel Process Piping, Рnom up to 10 MPa
SN 550-82: Specification for plastic process pipeline design
SNiP 2.03.11-85: Corrosion protection of buildings structures
SNiP 3.05.05-84: Processing equipment and process pipelines
SNiP 3.05.07-85: Automated systems
VSN 205-84: Instructions for the design of electric units of process automation systems
VSN 518-90: Timeframe Standards for Installation of Structural Elements for Factory and Industrial Buildings and Structures
The Document is Referenced By:
IM 14-51-94, v.2: Guidelines and explanations on topical issues of development of automation systems. Release 2. General questions of application of standard drawings
IM 14-58-2012: Reference book of standard drawings and normals used in the design and installation of automation systems
IM 4-12-95: Automation systems. Handbook of materials. Part 1. Basic materials
IM 51216464-009-01: Instructions for use of supporting cable structures of the series "P" on TU 3449-009-51216464-01
MR 14-02-2003: Selection and application of selective devices for pressure measuring instruments
RM 4-150-92: Process automation systems. Integrated norms of consumption of materials and products
RM 4-239-91: Automation systems. Dictionary-reference terms. Allowance to SNiP 3.05.07-85
RM 4-6-84: Process automation systems. Design of electrical and pipe wiring. Part 1. Electrical wiring. Allowance for the BCH 205-84/MMSS
|
Customers Who Viewed This Item Also Viewed:
 |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Plastics structured-wall pipes and their fittings for sewerage systems outside the buildings. Specifications
Language: English |
Vegetable oils. General technical requirements
Language: English |
Current transformers. General specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
