SNiP II-33-75
СНиП II-33-75
|
|
Heating, ventilation and air conditioning
Отопление, вентиляция и кондиционирование воздуха
Status: Not effective
Rules and regulations should be observed in the design of heating, ventilation and air conditioning of buildings and structures under construction for various purposes.
Нормы и правила должны соблюдаться при проектировании отопления, вентиляции и кондиционирования воздуха строящихся и реконструируемых зданий и сооружений различного назначения.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstroy of the USSR (State Committee of the Council of Ministers of the USSR for Construction),
10/20/1975
SKU: RUSS168367
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Documents System of normative documents in construction »
4. Normative documents for engineering equipment of buildings and structures and external networks »
к.40 Water supply and sewerage »
Construction (Max) »
Regulations »
Documents System of normative documents in construction »
4. Normative documents for engineering equipment of buildings and structures and external networks »
k.41 Heat supply, heating, ventilation and air conditioning »
PromExpert »
SECTION III. LABOR PROTECTION AND SAFETY »
II Industrial sanitation and occupational health »
3 Workspace air »
3.2 Improvement of air environment and normalization of microclimate parameters »
The Document is Replaced With:
SNiP 2.04.05-86: Heating, Ventilating, and Air Conditioning
As a Replacement Of:
SN 242-63: Design Instructions for Concentrated Air-Blowing Units
SN 258-63: Temporary technical conditions for the design, installation and operation of central heating systems with stamped steel welded panel-type radiators with rear connection
SN 354-66: Guidelines for the design and installation of central water heating systems with baseboard convectors
SN 86-60: Instructions for placing hatches for measuring the pressure of air flow in metal ducts of ventilation and air conditioning
SN 9-57: Instructions on calculating the heating surface of heating devices in equivalent square meters
SNiP I-G.5-62: Heating, ventilation and air conditioning. Equipment, fittings and materials
SNiP II-G.7-62: Heating, ventilation and air conditioning. Design Standards
The Document is Referenced By:
A3-804: Manual for the calculation of air ducts made from uniform parts
A3-840: Recommendations for selection of heating and recycling units
A3-877: Recommendations for calculating suction from equipment that emits heat and gases
B3-59: Temporary recommendations on the electrochemical purification of industrial wastewater from hexavalent chromium using steel electrodes
GOST 12.3.027-81: Occupational safety standards system. Foundry work. Safety requirements
GOST 28617-90: Metallic and non-metallic inorganic coatings of bicycles, motor cycles, scooters, motor bicycles. General requirements and methods of control
GOST 4426-80: Electrodes and nipples, with graphite. Specification
GOST 9.302-88: Unified system of corrosion and ageing protection. Metal and non-metal inorganic coatings. Control methods
Manual for SNiP 2.04.05-91: Benefit 3.91. Fan units
Manual for SNiP 2.04.05-91: Manual 4.91. Smoke protection in case of fire
Manual for SNiP 2.04.05-91: Allowance 14.91. New schemes and solutions for smoke protection of staircase elevators of multi-storey buildings
Manual for SNiP 2.04.05-91: Allowance 15.91. Smoke protection in case of fire and ventilation of underground car parks
Manual for SNiP 2.04.05-91: Benefit 5.91. Placement of ventilation equipment.
Manual for SNiP 2.04.05-91: Benefit 7.91. Duct layouts in a building
Manual for SNiP 2.04.05-91: Allowance 6.91. Fire resistant ducts.
Manual for SNiP 2.04.05-91: Benefit 2.91. Calculation of the receipt of heat of solar radiation in the premises
Manual for SNiP 2.04.05-91: Allowance 13.91. Fire protection requirements for heating, ventilation and air conditioning systems
Manual for SNiP 2.04.05-91: Benefit 8.91. The number of personnel operating heating, ventilation and air conditioning systems
Manual for SNiP 2.04.05-91: Manual 10.91 Designing Corrosion Protection
Manual for SNiP 2.04.05-91: Manual 1.91 Calculation and Distribution of Supply Air
Manual for SNiP 2.04.05-91: Allowance 12.91. Recommendations for calculating outdoor air infiltration in one-story industrial buildings
Manual for SNiP 2.04.05-91: Benefit 9.91. Annual energy consumption by heating, ventilation and air conditioning systems
Methodical instructions 2942-83: Improvement of working conditions at enterprises producing and using phosphors
MI 670-84: Guidelines. Determination of the need of testing units in production resources
MR 2291-81: Guidelines for improving the conditions of training and education of students of the communication specifications in the specialty telegraph
MR 3910-85: Guidelines for the sanitary control of the organization of circle activities in out-of-school institutions
MU 1737-77: Instructional and methodological guidelines on organization of exchange in hospitals treatment sections and operating units
MU 2039-79: Guidelines for the implementation of state sanitary supervision of the design, construction and operation of plants for biothermal processing of solid waste
MU 2515-81: Guidelines for the organization of training of students of higher educational institutions
ONTP 01-82/Minavtoprom: All-Union norms for technological design of engineering, instrument-making and metal-working enterprises. Forging shops
ONTP 01-86: All-Union standards for the technological design of engineering, instrument-making and metal-working enterprises. Forge and press shops
ONTP 11-85: All-Union norms for technological design of engineering, instrument-making and metal-working enterprises. Workshops for the production of tools and tooling
ONTP 16-86: All-Union standards for technological design of thermal areas, workshops, production facilities of enterprises of mechanical engineering, instrument engineering and metalworking
ONTP 2-87: All-Union standards for technological design of plastics processing facilities. II part
OST 108.020.131-85: Steam, Gas and Hydraulic Turbines. General requirements for conservation.
OST 2 N83-44-80: Occupational safety standards system. Arc and electroslag welding. Safety requirements
OST 2 N83-45-80: Occupational safety standards system. Contact welding. Safety requirements
OST 2 N83-46-80: Occupational safety standards system. Oxygen cutting. Safety requirements
OST 2 Н83-44-80: Occupational safety standards system. Electric arc welding and slag welding. Safety requirements.
OST 2 Н83-45-80: Labour safety standard system. Contact welding. Safety requirements.
OST 2 Н83-46-80: Labour safety standard system. Oxygen cutting. Safety requirements.
OST 4 G0.033.200: Solders and fluxes for soldering, solder pastes. Brands, composition, properties and scope (edition 1-78)
OST 64-7-472-83: Occupational safety standards system. Production processes of finished pharmaceutical products. Production of ampouled injections. Safety requirements.
PPBO-109-92: Fire Safety Regulations in Rail Transport
PPB-S-1983: Fire Safety Regulations for Buildings and Structures of Educational Institutions, Companies, and Organizations Administered by Minvuz USSR
PV NP 78: Rules for acceptance, testing and operation of the ventilation systems of oil refining and petrochemical enterprises
R 466-82: Guidelines for conducting induction training on labor protection in organizations and enterprises of the Ministry of Oil and Gas Industry
RD 102-61-87: Guidelines for certification, rationalization, accounting and planning of workplaces for drivers and maintenance workers at motor transport enterprises of the Ministry of Oil and Gas Construction
RD 31.52.10-82: Temporary ventilation systems for ship premises during repair. Rules for design and operation
RD 31.83.07-86: Occupational Safety and Health Management System - Recommended Practice for Reducing Noise Levels at Ship Repair Facilities Administered by the Ministry of the Merchant Marine
RD 50-443-83: Guidelines. Application of GOST 8.395-80 "GSI. Normal measurement conditions during calibration. General requirements"
RM 38.14.008-94: Guiding Material. Radial (centrifugal) and axial fans. Maintenance and repair.
RSN 68-87: Design of industrial and civil buildings of the West Siberian oil and gas complex
RTM 34-9TEP-04-79: Rules for the design of heating and ventilation (dust removal and cleaning of rooms) of the fuel supply paths of thermal power plants
SanPiN 2.3.4.545-96: Production of bread, cakes and confectionaries
SanPiN 5059-89: Sanitary rules for aircraft maintenance bases of civil aviation operating enterprises
SanPiN 5146-89: Temporary sanitary and hygienic norms and rules for the device, equipment, content and operating mode on personal electronic computers and video display terminals in computer rooms and display classes of all types of secondary schools
SNiP 2.10.02-84: Agricultural Products Storage and Processing Facilities
SNiP 2.10.05-85: Organizations, buildings and structures used for storage and processing of grain
SP 4079-86: Sanitary regulations for manufacturers of drugs
SP 4542-87: Sanitary rules for livestock enterprises
V3-33: Recommendations for designing the process part of refrigeration units for cooling of air conditioning systems and cooling systems for process equipment
VNTP 02-85: Industry-Specific Engineering Design Standards for General Purpose Warehouses
VNTP 03-86: Industry-Specific Engineering Design Standards for Cold-Storage Distribution Warehouses
VNTP 10-5-80/MChM SSSR: Instructions and norms for technological design and technical and economic indicators of the energy sector of ferrous metallurgy enterprises. Volume 28. Ferroalloy plants
VNTP 10-79/Minavtoprom: Norms of technological design of metal-coating workshops of automobile industry plants
VNTP 113-86: Wire Line Communications Facilities. Stations and nodes telegraphic and data transmission
VNTP 12-79/Minsel'hoz SSSR: Norms of technological design of warehouses of solid mineral fertilizers and pesticides for collective farms, state farms and chemicalization points
VNTP 37-86: Standards for technological design of non-ferrous metallurgy mines with underground mining
VNTP 81: Engineering Design Standards for Thermal Power Plants (VSN 29-81)
VNTP 9-1-80/MChM SSSR: Instructions and norms for technological design and technical and economic indicators of the energy sector of ferrous metallurgy enterprises. Metallurgical plants. Volume 11. Production of shielding gases
VNTP/MPS 85: Departmental norms of technological design. Devices of automation and telemechanics in railway transport.
VSN 36-77/Gosgrazhdanstroy: Instructions for the integrated use of geothermal waters for heat and cold supply of buildings and structures
VSN 40-84(r)/Gosgrazhdanstroj: Technical rules for spending of basic construction materials for the overhaul of residential buildings and utilities
|
Customers Who Viewed This Item Also Viewed:
 |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
High strength rolled steel. General specification
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads
Language: English |
Articulated connector devices with cast male and female parts for freight cars of articulated type. General technical specifications
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
