SNiP II-45-75
СНиП II-45-75
|
|
Main pipelines
Магистральные трубопроводы
Status: Not effective - Superseded
Standards should be observed when designing new and reconstructed main pipelines and branches from them with a nominal diameter of up to 1,400 mm (inclusive) with an overpressure of the medium not exceeding 100 kgf
Нормы должны соблюдаться при проектировании новых и реконструируемых магистральных трубопроводов и ответвлений от них условным диаметром до 1400 мм (включительно) с избыточным давлением среды не свыше 100 кгс/см2 для транспортирования: а) нефти, нефтепродуктов, природного и попутного, естественного и искусственного углеводородных газов из районов их добычи, производства или хранения до мест потребления (нефтебаз, перевалочных баз, пунктов налива, газораспределительных станций городов и населенных пунктов, отдельных промышленных и сельскохозяйственных предприятий и портов); б) сжиженных углеводородных газов (фракций С3 и С4 и их смесей), а также нестабильного бензина и нестабильного конденсата и других сжиженных углеводородов с насыщенными парами упругостью не свыше 16 кгс/см2 при температуре плюс 45 град. Цельсия из районов их добычи или производства (от головных перекачивающих насосных станций) до места потребления (нефтебаз, перевалочных баз, пунктов налива, промышленных предприятий, портов, газораздаточных станций и кустовых баз); в) товарной продукции в пределах головных и промежуточных насосных станций, станций подземного хранения газа, газораспределительных станций, замерных пунктов. Нормы не распространяются на проектирование трубопроводов, прокладываемых на территории городов и других населенных пунктов, а также в зоне вечномерзлых грунтов, морских акваториях и районах с сейсмичностью свыше 8 баллов для подземных и свыше 6 баллов для надземных трубопроводов.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstroy of the USSR (State Committee of the Council of Ministers of the USSR for Construction),
8/29/1975
SKU: RUSS168374
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Documents System of normative documents in construction »
3. Normative documents on urban planning, buildings and constructions »
K.34 Main and field pipelines »
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Metal structures »
Welding regulations »
Welding materials »
Welding regulations »
welding equipment »
Welding regulations »
Welding staff »
Welding regulations »
Admission Testing »
Welding regulations »
Certification »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Defects »
Welding regulations »
Assembly devices »
Welding regulations »
Welding work »
Manual welding »
Welding regulations »
Welding work »
Mechanized welding »
Welding regulations »
Welding work »
Automatic welding »
Welding regulations »
Welding work »
Surfacing »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Main materials »
Polymers »
Welding regulations »
Welding materials »
Electrodes »
Welding regulations »
Welding materials »
Wire »
Welding regulations »
Welding materials »
Fluxes »
Welding regulations »
Welding materials »
Gases »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
2003.200.13 Pipelines and their components »
As a Replacement Of:
SNiP I-D.4-62: Main steel pipelines. Materials and products
SNiP II-D.10-62: Main pipelines. Design Standards
The Document References:
GOST 10121-76: Selectively purified transformer oil
GOST 1012-72: Aviation petrol
GOST 10144-89: Enamels XB-124Specifications
GOST 10157-79: Gaseous and liquid argon. Specifications
GOST 10277-90: Putties. Specifications
GOST 10923-93: Ruberoid. Specifications
GOST 12871-93: Chrysotile asbestos - chrysotile. General specifications
GOST 13303-86: High-molecular polyisobutylene
GOST 15836-79: Bitumen-rubber insulating mastic. Specifications
GOST 15879-70: Glass ruberoid. Specifications
GOST 16338-85: Low-pressure polyethylene. Specifications
GOST 1928-79: Coal solvent. Specifications
GOST 20295-85: Welded steel pipes for gas and oil pipelines. Technical specifications
GOST 2084-77: Mobile gasoline Specifications
GOST 2246-70: Welding steel wire. Specifications
GOST 5457-75: Dissolved acetylene and gaseous acetylene for technical purposes. Specifications
GOST 5494-71: Pegmentary aluminium powder
GOST 5583-78: Industrial and medical gaseous oxygen
GOST 610-72: Oils for axle journals. Specifications
GOST 6617-76: Petroleum construction bitumen
GOST 7313-75: Enamels ХВ-785 and lacquer XB-784. Specifications
GOST 7415-86: Bituminous asbestos paper. Specifications
GOST 7827-74: Solvents of grades P-4, P-4A, P-5, P-5A, P-12 for paint materials. Specifications
GOST 8050-85: Carbon dioxide,
GOST 8731-74: Seamless hot-deformed steel pipes. Specifications
GOST 8733-74: Cold-formed and heat-formed seamless steel pipes. Technical requirements
GOST 9.015-74: Unified system of corrosion and ageing protection. Underground constructions. General technical requirements
GOST 9087-81: Welding melted fluxes
GOST 9109-81: Primers ФЛ-03k and ФЛ-03Ж. Specifications
GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST 9467-75: Metal covered electrodes for manual arc welding of structural and heat-resistant steels. Types
GOST 9544-93: Pipeline cut-off valves
GOST 9812-74: Petroleum insulating bitumen
R 235-76: Guidelines for the design of pipelines in the offshore zones of the seas (on ramps for the Caspian Sea)
R 442-81: Recommendations on the technology of blasting operations in frozen and rocky soils in the construction of trunk pipelines parallel to the existing steel underground pipelines
The Document is Referenced By:
Manual to SN 527-80: Manual to SN 527-80. On the strength design of the technological steel pipelines at Py up to 10 Mpa
OST 102-55-81: Parts of trunk pipelines, steel welded on Ru to 10.0 MPa (100 kgf
OST 102-61-81: Parts of pipelines steel welded at PN up to 10,0 MPa (100 kgf / cm2). 3-way joints with reinforcing overcoating. Dimensions
OST 102-62-81: Parts of pipelines steel welded at PN up to 10,0 MPa (100 kgf / cm2). Ellipse bottom covers, with flanges. Dimensions
P 09-83/VNIIG: Recommendations for calculating the hydroabrasive wear of slurry pipelines and pumps for hydraulic ash removal systems of thermal power plants
R 227-76: Guidelines for Technical Investigation of Line Pipeline Line Failures
R 235-76: Guidelines for the design of pipelines in the offshore zones of the seas (on ramps for the Caspian Sea)
R 259-77: Guide to the organization and technology of construction of the ammonia pipeline Togliatti-Grigorievsky Liman
R 282-77: Guidelines for the construction of pipe-in-pipe underwater pipelines for transitions of the ammonia pipeline Togliatti-Grigorievsky Liman
R 294-77: Guidance on methods for calculating subsea pipelines when diving to great depths
R 295-77: Guidelines for the technology and organization of the construction of cable communication lines in the mountains
R 301-77: Guidance on engineering assessment and forecasting of the actual structural reliability of main pipelines
R 359-79: Basic principles for calculating the strength of pipelines according to the theory of limiting processes of simple loading
R 397-80: Guidelines for the development of trenches in rocky and heavy soils by floating mechanisms during the construction of underwater crossings of main pipelines
R 412-81: Recommendations for the design and construction of offshore subsea oil and gas pipelines
R 420-81: Installation Guide for Subsea Pipelines with Reinforced Concrete Coatings and Weights
R 435-81: Guidelines for ballasting pipelines using fixed soils
R 451-82: Recommendations for the calculation of pipelines of multilayer pipes for dynamic loads
R 454-81: Guidelines for assessing the quality of the construction of the linear part of trunk pipelines
R 486-83: Guidelines for predicting thermal interaction of pipelines with the environment
R 499-83: Guide to automated strength analysis of the linear part of pipelines
R 500-83: Recommendations on hydro-geological forecasting for the construction of pipelines in over-wet areas, including permafrost areas
R 526-84: Recommendations for determining the flexibility and stress state of curvilinear sections of pipelines
R 536-84: Recommendations for the design of thermal insulation structures of trunk pipelines
R 541-84: Recommendations for calculating the efforts of an internal centralizer for assembling pipes with an initial ovality of sections
R 546-84: Computer-Aided Technique and Computer Calculation for Pipelines during Pressure Pulsation
R 578-85: Recommendations for testing main and field pipelines at low temperatures
R 585-85: Recommendations for the design of gas pipelines transporting cooled gas
RD 102-010-82: Specifications for the technological system of electrical protection of underground gas and oil pipelines during their construction against corrosion by stray currents
RD 39-00147105-001-91: Method for evaluating the performance of pipes in the linear part of the pipeline based on diagnostic information
RD 39-30-1090-84: Method for calculating maximum allowable pressures in underwater crossings of operating pipelines
RD 39-30-1333-85: Guidelines for corrosion protection by coatings on the outer surface of field pipelines in permafrost areas in Western Siberia
RD 39-30-139-79: Methods of thermal and hydraulic calculation of trunk pipelines under stationary and non-stationary pumping regimes of Newtonian and non-Newtonian oils in various climatic conditions
RD 39-30-494-80: Methods of optimizing the reservation of the designed main oil pipeline
RD 39-30-613-81: The methodology for choosing rational design solutions for laying pipelines taking into account the temperature difference
RD 39-30-657-81: Guidance on the mechanochemical preparation of the inner surface of pipelines for protective coatings applied in the field
VNTP 13-1-86/MChM SSSR: Standards for technological design of open-pit mining enterprises of ferrous metallurgy
VNTP 1-45-80/MChM SSSR: Instructions and norms for technological design and technical and economic indicators of the energy sector of ferrous metallurgy enterprises. Metallurgical plants. Volume 22. Methodological guidelines for the technological design of corrosion protection of underground metal structures and communications
VSN 163-83: Design Considerations for the Deformation of River Beds and Shorelines of Water Bodies at Underwater Petroleum and Natural Gas Trunk Pipeline Crossings
VSN 171-84: Instructions on welding technology and quality control of welded joints of field pipelines
VSN 2-112-79: Rules for the production of overhaul of the linear part of the main oil and gas pipelines
VSN 2-120-80/Minneftegazstroj: Instructions on the technology for welding pipelines and technological equipment during the installation of compressor and pumping stations
VSN 2-136-81: Instructions for selecting and using various types of weighting loads and anchoring devices for securing main pipelines against ascent
VSN 2-149-82: Instructions for the production of works in the construction of trunk steel pipelines. Insulation work
VSN 2-72-82: Instructions on the technology of butt welding of electric contact reflow of main pipelines of steel with a tensile strength of up to 60 kgf
VSN 51.2-84: Engineering Survey on Continental Shelf
VSN 51-03-78: Instructions for the design of pipelines for the transportation of liquefied hydrocarbons
|
Customers Who Viewed This Item Also Viewed:
 |
Industrial process measurement and control equipment. Reliability. General requirements and test methods
Language: English |
Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
Language: English |
System for ensuring the reliability and safety of construction sites. Loads and impacts. design standards
Language: English |
Heating, ventilation and air conditioning. Fire Safety Requirements
Language: English |
Reliability of atomic power stations and their equipment. General statements and reliability index nomenclature
Language: English |
Electromagnetic compatibility of technical equipment. Technical equipment for nuclear power plants. Requirement and test methods
Language: English |
Billets made of corrosion-resistant steels of 12Х18Н9Т, 12Х18Н10Т, 08Х18Н10Т, 10Х17Н13М2Т, 12Х18Н12Т and 03Х21Н32М3Б types.
Language: English |
Dependability in technics. Terms and definitions
Language: English |
System of products development and launching into manufacture. Technical assignment. Requirements to contents and form of presentation
Language: English |
Reliability in technology. Composition and general rules for setting reliability requirements
Language: English |
Rails of types P38 and P42. Technical conditions
Language: English |
Stainless corrosion resisting, heat-resisting and creep resisting steel and alloy on iron-nickel-based products. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
