ST TsKBA 099-2011
СТ ЦКБА 099-2011
|
|
Pipe fittings. Repairs. Organization of repair and general repair manual
Арматура трубопроводная. Ремонт. Организация ремонта и общее руководство по ремонту
Status: Effective - Introduced for the first time
The standard applies to pipeline valves for various industries and establishes: general requirements and recommendations for the development of repair documentation for specific products; general requirements for the organization and conduct of repairs aimed at ensuring industrial and environmental safety, improving the quality of repairs and reliability of valves during operation; volume and methods of fault detection, methods of repair, methods of control, adjustment, transportation and storage of reinforcement after repair, methods of testing components during the repair process; technological recommendations in the manufacture and restoration of parts and components of valves; allowable repair dimensions, within which it is possible to carry out repairs of parts and assemblies, as well as defects at which parts and fittings of the fittings cannot be repaired; volumes, test methods for assembled valves and comparison of quality indicators of repaired valves with their standard and pre-repair values.
Стандарт распространяется на трубопроводную арматуру для различных отраслей промышленности и устанавливает: общие требования и рекомендации по разработке ремонтной документации для конкретных изделий; общие требования к организации и проведению ремонта, направленные на обеспечение промышленной и экологической безопасности, повышение качества ремонта и надежности арматуры при эксплуатации; объем и методы дефектации, способы ремонта, методы контроля, настройки, транспортирования и хранения арматуры после ремонта, методы испытаний составных частей в процессе ремонта; технологические рекомендации при изготовлении и восстановлении деталей и узлов арматуры; допустимые ремонтные размеры, в пределах которых можно проводить ремонт деталей и узлов, а также дефекты, при которых детали и узлы арматуры ремонту не подлежат; объемы, методы испытаний арматуры в сборе и сравнение показателей качества отремонтированной арматуры с ее нормативными и доремонтными значениями.
Choose Language:
Format: Electronic (pdf/doc)
Approved: SJSC NPF TsKBA,
7/13/2011
SKU: RUSS169777
The Product is Contained in the Following Classifiers:
Organization Standards »
Standards NPF TsKBA »
Standards for pipe fittings (TPA) »
14. Operation and repair of injection molding machines »
14.3 Repair of injection molding machines »
Standards for pipe fittings (TPA) »
10. Production »
10.4 Surfacing »
The Document References:
Federal Law 69-FZ: Fire Safety
GOST 10198-91: Wooden boxes for weights of mass over 200 up to 20000 kg. General specifications
GOST 10905-86: Surface plates and face-plates. Specifications
GOST 12.3.002-75: Occupational safety standards system. Manufacturing processes. General safety requirements
GOST 12.3.005-75: Painting works
GOST 12.3.009-76: Occupational safety standards system. Loading and unloading works General safety requirements
GOST 12.3.025-80: Occupational safety standards system. Metal working by cutting. Safety requirements
GOST 14192-96: Cargo marking
GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15180-86: Flexible flat gaskets. Main parameters and dimensions
GOST 15467-79: Product quality control. Basic concepts. Terms and definitions
GOST 16093-2004: Basic norms of interchangeability. Metric screw thread. Tolerances. Clearance fits
GOST 166-89: Vernier callipers. Specifications
GOST 17756-72: Threaded plug-gauges with inserts with full-form of thread of diameters from 1 to 100 mm. Design and basic dimensions
GOST 17763-72: Threaded plug-gauges with full form of thread of diameters from 1 to 100 mm. Design and basic dimensions
GOST 18322-78: Equipment maintenance and repair system. Terms and definitions
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 19300-86: Instruments for measurement of surface roughness by the profile method. Contact profilographs and profilometers. Types and main parameters
GOST 19596-87: Spades
GOST 2.602-95: Unified system for design documentation. Repair documents
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 21623-76: System of technical maintenance and repair of equipment. Characteristics for evaluation of maintainability and rapairability. Terms and definitions
GOST 23170-78: Packing for products of engineering industry. General requirements.
GOST 25706-83: Magnifiers
GOST 25726-83: Letter and numerical hand stamps. Types and basic dimensions
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 30893.1-2002: Basic norms of interchangeability. General tolerances. Limit deviations for linear and angular dimensions without tolerance indications
GOST 30893.2-2002: Basic norms of interchangeability. General tolerances. Tolerances of form and position for features without individual tolerance indications
GOST 3134-78: White spirit
GOST 3333-80: Graphite lubricant
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 4380-93: Micrometers with inserts. Specifications
GOST 481-80: Compressed asbestos fibre sheets and gaskets from it. Specifications
GOST 5152-84: Gland Packing Specifications
GOST 577-68: Clock-type dial indicators graduated in unit divisions of 0,01 mm. Specifications
GOST 6267-74: Grease ЦИАТИМ-201. Specifications
GOST 6507-90: Micrometers. Specifications
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 8.050-73: State system for ensuring the uniformity of measurements. Reference conditions for linear and angular measurements
GOST 8.051-81: State system for ensuring the uniformity measurements. Permissible errors of measurement of linear dimensions to 500 mm
GOST 9.014-78: Unified system of corrosion and ageing protection. Temporary corrosion protection of products. General requirements
GOST 9.032-74: Unified, system of corrosion and ageing protection. Paint coatings. Groups, technical requirements and designations
GOST 9.301-86: Unified system of corrosion and ageing protection. Metal and non-metal inorganic coatings. General requirements
GOST 9.302-88: Unified system of corrosion and ageing protection. Metal and non-metal inorganic coatings. Control methods
GOST 9.303-84: Unified system of corrosion and ageing protection. Metallic and non-metallic inorganic coatings. General requirements for selection
GOST 9.402-2004: Unified system of corrosion and ageing protection. Paint coatings. Metal surface preparation for painting
GOST 9012-59: Metals. Method of Brinell hardness measurement
GOST 9013-59: Metals. Method of measuring Rockwell hardness
GOST 9378-93: Roughness comparison specimens
GOST 9562-81: Basic norms of interchangeability. Trapezoidal single-start screw thread. Tolerances
GOST 9847-79: Optical instruments for surface roughness parameters measuring. Basis parameters and types
GOST R 12.4.026-2001: Occupational safety standards system. Safety colors, safety signs and signal marking. Purpose and rules of application. General technical requirements and characteristics. Test methods
GOST R 12.4.230.1-2007: Occupational safety standards system. Personal eyes protection means. General technical requirements
GOST R 12.4.230.2-2007: Occupational safety standards system. Personal eye protection. Optical and non-optical parameters test methods
GOST R 51672-2000: Metrological ensuring of product testing for the assurance of conformity. General principles
GOST R 52376-2005: Heat-resistant spiral-wound gaskets. Types. Main dimensions
GOST R 52720-2007: Pipeline valves. Terms and definitions
GOST R 52760-2007: Pipeline valves. Requirements for the marking and distinctive painting
GOST R 53402-2009: Pipeline valves. Methods of control and testing
GOST R 53561-2009: Pipelines valves. Jackets of oval, octagonal section, lens steel for valves flanges. Design, dimension and general technical requirements
GOST R 53672-2009: Pipeline valves. General safety requirements
PB 10-382-00: Rules of hoisting crane structure and safe operation. Series 10. Revision 7.
PNAE G-7-009-89: Equipment and pipelines of nuclear power installations. Welding and overlaying, general provisions
PNAE G-7-010-89: Equipment and pipelines of nuclear energy facilities. Welded joints and beads. Testing rules
PNAE G-7-014-89: Standardized methods of testing of basic materials (semifinished products, weld joints and surfacing of equipment and piping of npp. Ultrasonic inspection. Part I. Control of basic materials (semifinished products)
PNAE G-7-016-89: Standardized methods of control of basic materials (semifinished products), welded joints and cladding of equipment and of pipelines of NPP. Visual and a measuring control
PNAE G-7-017-89: Unified technique of inspection of base materials (semifinished products), welded joints and deposits of equipment and pipelines of atomic power plants. Ultrasonic inspection
PNAE G-7-018-89: Safety guidelines. Standardized methods of control of basic materials (semi-finished products), welded joints and surfacing of NPP equipment and piping. Dye penetrant inspection
PNAE G-7-031-91: Uniform control methods for basic materials (semi-finished materials), welded joints and weldings on of equipment and pipelines of nuclear power plants. Ultrasonic testing. Part III. Thickness measurement of monometals, metals and corrosion resistant coat
RD 03-606-03: Instructions for visual and measuring control
RD EO 0027-2005: Instructions for determining the mechanical properties of metal of equipment of nuclear power plants using gumless methods according to hardness characteristics
RM 3-62: Guiding Technical Material. Appendix to power calculations of valves
ST TsKBA 005.1-2003: Pipe fittings. Metals used in the valve industry. Part 1. Basic requirements for the choice of materials
ST TsKBA 010-2004: Pipe fittings. Forgings, stampings and rolled products. Technical requirements
ST TsKBA 014-2004: Pipe fittings. Steel castings. General technical conditions
ST TsKBA 016-2005: Pipe fittings. Heat treatment of parts, billets and welded assemblies from high-alloy steels, corrosion-resistant and high-temperature alloys
ST TsKBA 019-2006: Pipe fittings. Thermally expanded graphite based seals. General technical requirements
ST TsKBA 025-2006: Pipe fittings. Welding and quality control of welded joints. Technical requirements
ST TsKBA 026-2005: Pipe fittings. Heat treatment of blanks from carbon and alloyed structural steels. Typical process
ST TsKBA 030-2006: Pipe fittings. Springs helical cylindrical. General technical conditions
ST TsKBA 037-2006: Pipe fittings. Packing glands. Construction, main dimensions and technical requirements
ST TsKBA 042-2008: Pipe fittings. Electrolytic, chemical, anodic and diffusion coatings
ST TsKBA 046-2007: Pipe fittings. Degreasing methods
ST TsKBA 053-2008: Pipe fittings. Surfacing and quality control of weld surfaces. Technical requirements
ST TsKBA 058-2008: Pipe fittings. Gaskets of paronite and rubber. Sizes and technical requirements
ST TsKBA 059-2008: Pipe fittings. Antifriction grease. Scope, application rates and application methods
ST TsKBA 061-2010: Pipe fittings. Temporary anti-corrosion protection. General requirements for the choice of means and methods of protection
ST TsKBA 067-2008: Pipe fittings. Spiral-wound heat-resistant gaskets for body-to-lid connections. Types, main dimensions and technical requirements
ST TsKBA 075-2009: Pipe fittings. Preparation of graphite grease
ST TsKBA 081-2009: Pipe fittings. Passport Recovery Procedure
ST TsKBA 082-2009: Pipe fittings. Input control
ST TsKBA 089-2010: Pipe fittings. Welding defects castings. Technical requirements
ST TsKBA 091-2011: Pipe fittings. Determination of mechanical properties of steel based on hardness measurement
ST TsKBA 098-2011: Pipe fittings. Repair of surfacing. Technical requirements
The Document is Referenced By:
GOST R 56001-2014: Pipeline valves for objects of gas industry. General specifications
|
Customers Who Viewed This Item Also Viewed:
 |
Industrial process measurement and control equipment. Reliability. General requirements and test methods
Language: English |
Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
Language: English |
System for ensuring the reliability and safety of construction sites. Loads and impacts. design standards
Language: English |
Heating, ventilation and air conditioning. Fire Safety Requirements
Language: English |
Reliability of atomic power stations and their equipment. General statements and reliability index nomenclature
Language: English |
Electromagnetic compatibility of technical equipment. Technical equipment for nuclear power plants. Requirement and test methods
Language: English |
Billets made of corrosion-resistant steels of 12Х18Н9Т, 12Х18Н10Т, 08Х18Н10Т, 10Х17Н13М2Т, 12Х18Н12Т and 03Х21Н32М3Б types.
Language: English |
Dependability in technics. Terms and definitions
Language: English |
System of products development and launching into manufacture. Technical assignment. Requirements to contents and form of presentation
Language: English |
Reliability in technology. Composition and general rules for setting reliability requirements
Language: English |
Rails of types P38 and P42. Technical conditions
Language: English |
Stainless corrosion resisting, heat-resisting and creep resisting steel and alloy on iron-nickel-based products. Specifications
Language: English |
Natural gas for industrial and municipal purposes. Technical conditions
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
