imgalt

GOST 16037-80

ГОСТ 16037-80

Welded joints in steel pipelines. Main types, design elements and dimensions

Соединения сварные стальных трубопроводов. Основные типы, конструктивные элементы и размеры

Status: Effective - Supersedes. The limitation of effectiveness has been lifted: Protocol No. 5-94 of the IGU dated 05.17.94 (IUS 11-12-1994)

The standard applies to welded joints of steel pipelines and establishes the main types, structural elements and dimensions of welded joints of pipes with pipes and fittings. The standard does not apply to welded joints used for the manufacture of pipes from sheet or strip material.

Стандарт распространяется на сварные соединения трубопроводов из сталей и устанавливает основные типы, конструктивные элементы и размеры сварных соединений труб с трубами и арматурой. Стандарт не распространяется на сварные соединения, применяемые для изготовления самих труб из листового или полосового материала.

Choose Language: 
Format: Electronic (pdf/doc)

Approved: USSR State Committee for Standards, 4/24/1980

SKU: RUSS17784

Price: $198.00



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 25 Mechanical Engineering »

Welding regulations » Welding work »

Welding regulations » Main materials »

Welding regulations » Pipelines »

Welding regulations » Metal structures »

Welding regulations » Welding materials »

Welding regulations » Non-destructive control »

Welding regulations » Assembly devices »

Welding regulations » Main materials » Steel, cast iron »

Welding regulations » Welding materials » Electrodes »

Welding regulations » Welding materials » Fluxes »

Welding regulations » Welding materials » Gases »

Standards for pipe fittings (TPA) » 6. Standards of connecting sizes of piping valves (TPA) » 6.2 Weld connection »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.12 Testing and control of products of metallurgical industry » 4.12.6 Metal products »

ISO classifier » 25 MECHANICAL ENGINEERING » 25.160 Welding, brazing and hard soldering » 25.160.40 Welds and welding »

National standards » 25 MECHANICAL ENGINEERING » 25.160 Welding, brazing and hard soldering » 25.160.40 Welds and welding »

National Standards for KGS (State Standards Classification) » Latest edition » V Metals and metal products » V0 General rules and regulations on metallurgy » V05 Welding and cutting of metals. Soldering, riveting »

National Standards for OKSTU » SYSTEMS OF GENERAL TECHNICAL AND ORGANIZATIONAL-METHODOLOGICAL STANDARDS » One-piece connections (welding, riveting, soldering, etc.) »


As a Replacement Of:

GOST 16037-70: Welds of welded joints of steel pipelines. Main types and structural elements

The Document References:

GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications

GOST 2789-73: Surface roughness. Parameters and characteristics

The Document is Referenced By:

GOST 5264-80: Manual arc welding. Welding joints. Main types, design elements and dimensions

ATK 26-18-10-94: Devices for Installation of Temperature Measuring Devices for Use at Nominal Pressure from 0.6 to 16.0 MPa. Plugs. General Technical Requirements

ATK 26-18-14-98: Flanges of vessels and apparatus steel flat welded to a conditional pressure up to Ru 0.1 MPa. Design, dimensions and general technical requirements

Decision 162: On the list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis ensures compliance with the requirements of the technical regulations of the Eurasian Economic Union "On requirements for main pipelines for the transportation of liquid and gaseous hydrocarbons (TR EAEU 049/2020), and the list of international and regional (interstate) standards, and in their absence - national (state) standards that contain rules and methods of research (tests) and measurements, including sampling rules necessary for the application and implementation of the requirements of technical regulation of the Eurasian Economic Union "On requirements for pipelines for the transportation of liquid and gaseous hydrocarbons (TR EAEU 049/2020) and conformity assessment of technical regulation objects

DiOR 05: Methodology of diagnosing of technical condition and determining of residual life of process equipment of oil refineries and petrochemical plants

GOST 10617-83: Heating boilers with heat output heating capacity from 0.10 to 3.15 mw

GOST 12367-85: Tube mills of grinding units. General technical specifications

GOST 12893-2005: Single-seated, double-seated and cage control valves. General specifications

GOST 13531-74: Concrete placers for precast reinforced concrete factories

GOST 13547-2015: Pipeline valves. Butterfly wicket valves. General specifications

GOST 13981-87: Forms for reinforced concrete pressure pipes made by vibrohydropressed method. Specifications

GOST 14771-76: Gas-shielded arc welding. Welded joints. Main types, design elements and dimensions

GOST 17380-2001: Carbon and low-alloy steel butt-welding fittings. General specifications

GOST 17380-83: Seamless welded steel pipeline components for Pn £ 10 MPa (£ 100 kgf/cm2). Specifications

GOST 18103-84: Installations for manufacturing reinforced concrete three-dimensional elements of sanitary engineering cabins and lift shafts. Specifications

GOST 20572-83: Two-screw pumps and pump units. Specification

GOST 21345-2005: Ball, lifting-plug and cylindrical cocks for nominal pressure at most PN 250. General specifications

GOST 23074-85: Fertilizer placers for liquid organic fertilizers

GOST 23355-78: Threaded pipeline connections. Ball nipple. Construction

GOST 23484-79: Electrohydraulic-plants for removing of cores. Technical requirements

GOST 23982-85: Fertilizing machinery

GOST 24092-80: Threaded tube connections. Passage unions for welding. Construction

GOST 24950-81: Bent branches and curved inserts for the turns of the linear parts of steel long distance pipe lines

GOST 25781-2018: Steel molds for the manufacture of reinforced concrete products. Technical specifications

GOST 25781-83: Steel moulds for reinforced concrete members. Specifications

GOST 27310-87: Potato combines

GOST 28016-89: Threaded pipeline connections. Welded conical nipple. Construction

GOST 28759.5-90: Flanges of vessels and apparatuses

GOST 30767-2002: Gas lift well use equipment. Safety requirements and test methods

GOST 30768-2001: Control head oil field equipment. Test methods

GOST 31294-2005: Direct-acting safety valves. General specifications

GOST 31826-2012: Gas cleaning and dust catching equipment. Bag filters. Wet dust catching equipment. Safety requirement. Methods of testing

GOST 31830-2012: Electrostatic precipitators. Safety requirement and methods of testing

GOST 31831-2012: Centrifugal dust collectors. Safety requirement and methods of testing

GOST 31832-2012: Well sucker rod pump drives. General technical requirements

GOST 31834-2012: Adsorptive gas cleaners. Safety requirements and test methods

GOST 31837-2012: Abcorptive gas purifiers. Safety requirements and test methods

GOST 31841-2012: Petroleum and natural gas industries. Well service equipment. General technical requirements

GOST 31844-2012: Petroleum and natural gas industries. Drilling and production equipment. Hoisting equipment. General technical equipments

GOST 32569-2013: Steel pipe technology. Requirements for design and operation of explosive and chemically dangerous production

GOST 32949-2014: Automobile roads of general use. Supports of stationary electric lighting. Control methods

GOST 33164.1-2014: Mining equipment. Longwall powered roof shocks. Section of support. General specifications

GOST 33423-2015: Pipeline valves. Swing and lift check valves. General specifications

GOST 33857-2016: Pipe fittings. Welding and quality control of welded joints. Technical requirements

GOST 34011-2016: Gas distribution systems. Block gas delivery stations. Cabinet gas delivery stations. General technical requirements

GOST 34059-2017: Internal buildings and structures utilities. Arrangement of heating, heating and cooling water supply systems. General technical requirements

GOST 34094-2017: Steel tubes. Preparation of ends of tubes and fittings for welding. General technical requirements

GOST 34293-2017: Pipeline valves. Metal ball valves for petroleum, petrochemical and allied industries. General specifications

GOST 34294-2017: Cryogenic pipeline valves. General specifications

GOST 34473-2018: Pipe fittings. Cranes spherical steel all-welded for water thermal networks. General technical conditions

GOST 34587-2019: Hoisting cranes. Metal constructions. Manufacturing requirements

GOST 34881-2022: Trunk pipeline transport of oil and petroleum products. Stationary booms for containment of oil and oil products spills. General technical conditions

GOST 34904-2022: Ship pipeline valves. General specifications

GOST 5464-75: Pontoons of pressure floating mud pipelines and pipelines. General specifications

GOST 5466-74: Soil transfering pipes

GOST 5761-2005: Valves for nominal pressure at most PN 250. General specifications

GOST 5762-2002: Pipeline industrial valves. Gate valves PN<=250. General specifications

GOST 7496-84: Beet harvesters

GOST 8713-79: Flux welding. Welded joints. Maih types design elements and dimensions

GOST R 50073-92: Pipelines flange types joint fittings. Specifications

GOST R 50608-93: Refrigerating equipment. Steel apparatus. Welded joints. Technical requirements and checking methods

GOST R 51365-2009: Petroleum and natural gas industries. Drilling and production equipment. Wellhead and Christmas tree equipment. General specifications

GOST R 51365-99: Control head oil field equipment. General specifications

GOST R 51382-2011: Heating boilers. Part 4. Heating boilers with forced draught burners. Special requirements for boilers with forced draught oil burners with output up to 70 kW and maximum operating pressure of 0,3 MPa. Terminology, special requirements, test methods and marking

GOST R 51562-2000: Gas cleaning and dust catching equipment. Bag filters. Wet dust catching equipment. Safety requirement. Methods of testing

GOST R 51707-2001: Electrostatic precipitators. Safety requirement and methods of testing

GOST R 51708-2001: Centrifugal dust collectors. Safety requirement and methods of testing

GOST R 51763-2001: Well sucker rod pump drives. General technical requirements

GOST R 51878-2002: Adsorptive gas cleaners. Safety requirements and test methods

GOST R 52153-2003: Radiation-protective boxes. General specifications

GOST R 52209-2004: Hose assemblies for gas burners and gas appliances. General technical requirements and test methods

GOST R 52445-2005: Absorptive gas purifiers. Safety requirements and test methods

GOST R 52664-2006: Welded pipe sheet piles. General specifications

GOST R 52768-2007: Centrifuges for industries working with radioactive media. General technical requirements and test methods

GOST R 53192-2008: Welded steel structures of freight cars. Technical requirements

GOST R 53671-2009: Pipeline valves. Swing and lift check valves. General specifications

GOST R 53673-2009: Pipeline valves. Butterfly wicket valves. General specifications

GOST R 53680-2009: Petroleum and natural gas industries. Well service equipment. General technical requirements

GOST R 53683-2009: Petroleum and natural gas industries. Drilling and production equipment. Hoisting equipment. General technical rudiments

GOST R 53790-2010: Non-traditional technologies. Energetics of biowastes. General technical requirements for biogas sets

GOST R 53961-2010: Fire-fighting equipment. Underground fire hydrants. General technical requirements. Test methods

GOST R 54086-2010: Pressure regulators. General specifications

GOST R 54440-2011: Heating boilers. Part 1. Heating boilers with forced draught burners. Terminology, general requirements, test and marking

GOST R 54892-2012: Installation of air separation plants and other cryogenic equipment. General provisions

GOST R 54960-2012: Gas distribution systems. Block gas delivery stations. Cabinet gas delivery stations. General technical requirements

GOST R 55018-2012: Pipeline valves for objects of energetics. General specifications

GOST R 55020-2012: Pipeline valves. Knife gate valves for trunk pipelines. General specifications

GOST R 55429-2013: Hoop-in detachable joints of pipelines. Design, dimensions and general specifications

GOST R 55474-2013: Gas distribution systems. Requirements for gas distribution networks. Part 2. Steel gas pipelines

GOST R 55474-2019: Gas distribution systems. Gas distribution networks of natural gas. Part 2. Steel gas pipelines

GOST R 55942-2014: Steel tubes. Preparation of ends of tubes and fittings for welding. General technical requirements

GOST R 56001-2014: Pipeline valves for objects of gas industry. General specifications

GOST R 56400-2015: Petroleum and natural gas industries. Design and operation of offshore terminals of liquefied natural gas. General requirements

GOST R 58095.1-2018: Gas distribution systems. Requirements for gas consumption networks. Part 1. Steel gas pipelines

GOST R 58249-2018: Machines for planting, harvesting, post-harvest processing of potatoes. Technical requirements

GOST R 58619-2019: The main pipeline transport of oil and oil products. Tank equipment. Pontoons. General specifications

GOST R 58620-2019: The main pipeline transport of oil and oil products. Tank equipment. Acceptance devices for tanks. General specifications

GOST R 58778-2019: Gas distribution systems. Gas distribution networks and gas consumption. Category 1a high pressure gas pipelines

GOST R 58880-2020: Marine drinking water system. Design rules

GOST R 58934-2020: Plants for the manufacture of reinforced concrete volume blocks of sanitary cabins and elevator shafts. Specifications

GOST R 58935-2020: Forms for the manufacture of reinforced concrete vibrohydropressed pressure pipes. Specifications

IM 14-51-00: Guidelines and explanations on topical issues of creating automation systems. Release 4. New standard drawings of the Montazhavtomatika association

KPO 01.05.12-05: Catalog-list of equipment. Boiler equipment. Volume 2

KPO 01.05.12-05: Catalog-list of equipment. Boiler equipment. Volume 2

KPO 04.03.13-06: Catalog-list of equipment. Instruments for measuring and regulating the flow, quantity, level and composition of a substance

Manual: Manual for impulse and low consumption fire extinguishing systems

Manual for SNiP 3.05.02-88: Manual on technology and organization of the construction of pipelines for gas supply systems in rural areas of the Non-chernozem zone of the RSFSR

MDS 53-1.2001: Recommended Practice for Installation of Steel Structural Elements

MR 14-02-2003: Selection and application of selective devices for pressure measuring instruments

MSN 42-01-2011: Gas distribution systems

MU 0397-00.004: Methods of conducting non-destructive testing of parts of the boiler installation PPUA-1600/100

OST 108.030.133-84: Pipe elements of steam boiler heat surfaces under pressure less than 4 MPA, water boilers and heat-recovery boilers. Technical requirements, acceptance and control methods.

OST 108.101.102-76: Water-steam heaters. Forward water chambers (with flat bottom, two-way). Design and dimensions.

OST 108.101.103-76: Water-steam heaters. Forward water chambers (with flat bottom, four-way). Design and dimensions.

OST 108.101.104-76: Water-steam heaters. Forward water chambers (with elliptic bottom, two-way). Design and dimensions.

OST 108.101.105-76: Water-steam heaters. Forward water chambers (with elliptic bottom, four -way). Design and dimensions.

OST 108.101.108-76: Water-steam heaters. Aft water chambers (with elliptic bottom, two-way). Design and dimensions.

OST 108.101.109-76: Water-steam heaters. Aft water chambers (with elliptic bottom, four -way). Design and dimensions.

OST 108.101.110-76: Water-steam heaters. Covers. Design and dimensions.

OST 108.101.111-76: Water-steam heaters. Covers. Design and dimensions.

OST 108.313.102-76: Water-steam heaters. Casings. Branch pipes with flanges. Design and dimensions.

OST 24.200.02-91: Assembling units of steel pipelines on nominal pressure<=10 MPa (100 kgf/cm2) of complete technological lines. General specifications.

OST 26.260.18-2004: Process modules for oil and gas industry. General technical specifications

OST 26.260.462-99: Devices for installation of instruments measuring the temperature for PN from 0.6 to 16 MPa. Types, design, dimensions and general technical requirements

OST 26.260.472-2000: devices for installation of pressure gauges and pressure selection. General technical requirements.

OST 26.260.758-2003: Metal structures. General technical requirements.

OST 26-01-1159-75: Pipe input-outputs of steel welded containers and devices. Technical requirements.

OST 26-01-1434-87: Welding of steel technological pipelines on nominal pressure over 10 to 100 MPa (over 100 to 1000 kgf/cm2). Technical requirements.

OST 26-02-376-78: Technological units of gas and oil industry. General technical requirements.

OST 26-04-2388-79: Welding by melting of the steels. Welded connections. Types, constructive elements and dimensions.

OST 26-18-5-88: Technological units of gas and oil industry. General technical requirements.

OST 26-3-87: Welding in chemical mechanical engineering. Main provisions.

OST 34-10-417-90: Details and prefabricated units of pipelines of nuclear plants, working P<2.2 MPa, t ≤ 300 °C. Butt-welded joints and corners. Types and sizes.

OST 36-13-90: Shields and consoles of automation systems for technological processes. General technical conditions

OST 36-143-88: Installation for production equipment and process piping. Workflow project. Procedure of development, structure and content.

OST 36-145-88: Steel technological pipelines for pressure Ру up to 10 MPa. Fluxing automatic arc welding. Typical technological process.

OST 36-26-77: Welded details of pipelines Dy 500-1400 mm made of carbon steel for Pnom <= 2.5 MPa (≈ 25 kg/cm2). General technical requirements.

OST 36-39-80: Steel technological pipelines made of carbon and alloy steels for pressure Ру up to 9.81 MPa (100 kgf / cm2). Shielded manual metal arc welding. Typical technological process.

OST 36-62-81: Hoisting equipment. General technical requirements.

OST 36-75-83: Non-destructive testing. Pipeline welded joints. Ultrasonic method

OST 36-79-83: Steel process pipes of carbon and low alloy steels Pi up to 10 MPa (100 kgs/cm2). Semi-automatic welding with consumable electrode in carbon dioxide. Typical process.

OST 95 10440-2002: Equipment for radioactive environments. Welded joints. Types and dimensions and structural elements.

OTU 3-01: Vessels and apparatuses. General specifications for the repair of buildings

PB 03-108-96: Process pipeline design and safe operation rules

PGVU 021-92: Unified dust and air duct elements. Welded assemblies of blocks and elements of ducts of dust and gas air ducts of thermal power plants. Design and dimensions

PNAE G-10-031-92: Basic provisions for localizing safety system elements welding on nuclear stations

PNST 680-2022: Oil and gas industry. Underwater production systems. Factory-made fittings

RD 01-001-06: Welding of steel gas pipelines and the gas equipment in the city municipal services and power installations.

RD 153-112-014-97: Guidelines on Accident Response and Repair at Petroleum Product Trunk Pipelines

RD 153-34.0-04.185-2003: Machines and equipment for construction, technical re-equipment and repair of energy facilities. Requirements for design, materials, manufacturing, acceptance and testing

RD 153-34.1-003-01: Welding, heat treatment and control of copper pipe systems and pipelines at power equipment installation and repair.

RD 153-34.1-39.504-00: General technical requirements for fittings of CHP plant ( TPP OTT - 2000).

RD 22-207-88: Lifting machines. General requirements and production standards

RD 22-326-97: Self-propelled jib cranes and loader cranes. Overhaul. General technical conditions

RD 26.260.010-2002: The leading document on standardization. The list of standard documentation on standardization on the cells and devices working under pressure.

RD 26.260.010-97: List of Regulatory Documents on Standardization for Pressure Vessels and Apparatus

RD 26-02-80-2004: The leading document. Welded coils for pipe furnaces. Requirements to design, production and delivery.

RD 34.10.130-96: Instructions for visual and measuring control.

RD 34.20.595-97: Recommended Practice for Inspection of the Operating Condition of Public and Domestic Steel Gas Pipelines for Gas Supply Systems of Thermal Power Stations, Peak Boiler Plants, and Piped Heat Supply System Boiler Plants. General Requirements. Methods for

RD 36-62-00: Hoisting equipment. General technical requirements.

RD 38.13.004-86: Operation and repairs of process pipelines operating under pressure up to 10.0 MPa (100 kgf/cm2)

RD 39-0147014-348-89: Guidelines for Corrosion Protection of Field Equipment Using Domestically Manufactured Inhibitors

RD 39-0147014-535-87: Instructions for welding at installation and repair of pipelines and critical metal structures in organizations and enterprises of the Ministry of oil and gas industry.

RD 39-0147103-338-88: Temporary standards for the design of electric heating above-ground main pipelines (Axial electric heating system of ASE)

RD 39-110-91: Main pipeline accident and damage elimination instructions

RD 39-132-94: Regulations for Operation, Inspection, Repair and Rejection of the Field Pipelines 1994

RD 39-3-221-79: Instructions for corrosion protection of oilfield equipment using inhibitors of types IA, ID

RD NIIKranostroeniya 03-05: Guidelines. Jib cranes for general use and cranes; Overhaul. General specifications

RMD 40-20-2013 Sankt-Peterburg: Designing and installation pipelines for water supply and sewage systems in Saint-Petersburg

RMD 40-20-2016 Sankt-Peterburg: Installation of water supply and drainage networks in St. Petersburg

RTM 108.940.08-85: Welded structures of power equipment. General requirements for structural and process design

RTM 24-85: Information index of state, republican and industry standards, technical specifications for materials and products used in the design of furnaces and dryers

SA 03-005-07: Industrial pipelines of oil-refining, petrochemical and chemical industry. Requirements to configuration and operation

SNiP 3.05.01-85: Indoor plumbing systems

SNiP 3.05.03-85: Heat networks

SNiP 3.05.05-84: Processing equipment and process pipelines

SNiP 3.05.07-85: Automated systems

SNiP 42-01-2002: State committee of Russian Federation for construction and residential-utility complex (GOSSTROY OF Russia)

SNiP III-34-74: Automation Systems

SP 129.13330.2019: External networks and water supply and sewerage facilities

SP 341.1325800.2017: Underground engineering communications. Lining of by a method of the horizontal directional drilling

SP 42-102-2004: Design and construction of gas pipelines from metal pipes. To replace SP 42-102-96

SP 70.13330.2012: Bearing and enclosing structures. Updated living edition of SNiP 3.03.01-87

SP 73.13330.2012: Internal sanitary-technical systems

SP 73.13330.2016: Internal sanitary-technical systems

SP 77.13330.2016: Systems of automation.&nbsp;

ST TsKBA 025-2006: Pipe fittings. Welding and quality control of welded joints. Technical requirements

SZK 4-3-90: Instruments for measuring and controlling flow. Installation in the pipeline. Part I. Counters

TU 1317-233-0147016-02: Seamless hot-deformed oil and gas pipes of increased reliability during operation for the fields of OAO Tomskneft VNK

TU 1462-203-0147016-01: Welding steel connection parts for operation in oil-field environments with increased corrosion activity. Technical conditions

TU 1468-001-17192736-01: Seamless welded bends made of alloy and high alloy steel

TU 1468-010-593377520-2003: Seamless steel welded joints for pipelines, of increased operational reliability, intended for the field construction of OAO TNK

TU 26-18-38-90: Parts of seamless welded pipelines from steel grades 15Х5М, 12Х1МФ, 12Х18Н10Т, 08Х22Н6Т

TU 34-38-20135-94: Tubular air heaters of stationary boilers. Technical conditions for major repairs

TU 34-38-20189-94: Gas-oil burners for steam stationary boilers. Technical conditions for major repairs

TU 34-38-20190-94: Burner, types pulverized steam stationary boilers. Technical conditions for major repairs

TU 34-38-20191-94: Headset stationary boilers. General technical conditions for major repairs

TU 36-1686-82: Bends are steeply curved with an angle of 90 degrees from steel grades 15X5M, 08X18NIOT, 12X18NIOT and 10X17H13M2T seamless welded on the Rou is less than 10 MPa

TU 3631-002-76457067-2012: Dynamic Pumps and Pump Units MST-TsN type and spare parts for them

TU 3742-011-34390194-2003: Check valves DN 100-1400 PN 8, 0 MPa; PN 12, 5 MPa; PN 16, 0 MPa. Technical conditions

TU 4218-008-51216464-01: Selection device. Technical conditions

VNTP 04-94: Engineering Design Standards for Wine Bottling Plants

VNTP 10M-93: Engineering Design Standards for Microbreweries

VNTP 11-93: Engineering Design Standards for Facilities for the Production of Barley Brewer's Malt

VNTP 26-94: Standards for technological design of sparkling wine factories (production of Soviet champagne using a continuous tank method)

VNTP 34-93: Engineering Design Standards for Alcohol Industry Facilities

VSN 006-89: Construction Of Main And Field Pipelines Welding

VSN 07-81/Minoborony: Technical rules of quality control and acceptance of installation work at the facilities of the Ministry of Defense

VSN 362-87: Disinfections and Etching of Pipelines

VSN 39-87: Ordinance for Planned Preventive Maintenance and Operation of Production Equipment at Construction Industry Companies Administered by the USSR Gosagprom. Part 1

VSN 41.88: Design of ice-resistant stationary platforms

VSN 411-88: Installation of Lubricating, Hydraulic, and Pneumatic Systems for General Industrial Applications

VSN 416-81: General Specified Quantity Allowances for Building Materials. Compendium 30: Welding Operations

VSN 452-84: Production rates of consumption of materials in construction. Welding pipes made ??of alloy steel, automatic submerged arc welding of sheet structures, welding rods and valve inserts, gas cutting

VSN 461-85: Instructions for bonding joints of steel pipelines

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English
Price: $283.00
imgalt
Clear sheet glass. Specifications
Language: English
Price: $250.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!