imgalt

GOST R 52079-2003

ГОСТ Р 52079-2003

Steel welded pipes for trunk gas pipelines, oil pipelines and oil products pipelines. Specifications

Трубы стальные сварные для магистральных газопроводов, нефтепроводов и нефтепродуктопроводов. Технические условия

Status: Not effective - Canceled. Registration information 133-st dated 06/05/2013 (Rosstandart official website)

This standard applies to steel welded longitudinal and spiral-seam pipes with a diameter of 114-1420 mm used for the construction and repair of gas pipelines, oil pipelines and oil pipelines transporting non-corrosive-active products (natural gas, oil and oil products) with an excess working pressure of up to 9 8 MPa (100 kgf

Настоящий стандарт распространяется на стальные сварные прямошовные и спирально-шовные трубы диаметром 114-1420 мм, применяемые для строительства и ремонта магистральных газопроводов, нефтепроводов и нефтепродуктопроводов, транспортирующих некоррозионно-активные продукты (природный газ, нефть и нефтепродукты) при избыточном рабочем давлении до 9,8 МПа (100 кгс/см кв.) и температуре окружающей среды до минус 60 град. С

Choose Language: 
Format: Electronic (pdf/doc)

Approved: Gosstandart of Russia, 6/9/2003

SKU: RUSS18576

Price: $335.00



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 77 Metallurgy »

Welding regulations » Welding work »

Welding regulations » Main materials »

Welding regulations » Pipelines »

Welding regulations » Welding materials »

Welding regulations » Welding staff »

Welding regulations » Admission Testing »

Welding regulations » Certification »

Welding regulations » Documentation »

Welding regulations » Non-destructive control »

Welding regulations » Mechanical Testing »

Welding regulations » Heat treatment »

Welding regulations » Defects »

Welding regulations » Main materials » Steel, cast iron »

Welding regulations » Welding materials » Fluxes »

Welding regulations » Welding materials » Gases »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.12 Testing and control of products of metallurgical industry » 4.12.4 Iron and steel products »

ISO classifier » 77 METALLURGY » 77.140 Iron and steel products » 77.140.75 Steel pipes and tubes for special purposes »

National standards » 77 METALLURGY » 77.140 Iron and steel products » 77.140.75 Steel pipes and tubes for special purposes »

National Standards for KGS (State Standards Classification) » Latest edition » V Metals and metal products » V6 Pipes metal and pipe products » V62 Steel pipes and their connecting parts »


The Document References:

GOST 10006-80: Metal pipes

GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications

GOST 10692-80: Steel and cast iron pipes and fittings. Rules for acceptance of marking, packing, transportation and storage

GOST 11358-89: Dial-type thickness gauges and dial-type wall thickness gauges graduated in 0,01 and 0,1 mm. Specifications

GOST 12344-2003: Alloyed and high-alloyed steels. Methods for determination of carbon

GOST 12344-88: Alloyed and high-alloyed steels. Methods of carbon determination

GOST 12345-2001: Alloyed and high-alloyed steels. Methods of sulphur determination

GOST 12346-78: Alloyed and high-alloyed steels. Methods of silicon determination

GOST 12347-77: Alloyed and high-alloyed steels. Methods for determination of phosphorus

GOST 12348-78: Alloyed and high-alloyed steels. Methods of manganese determination

GOST 12349-83: Alloyed and high-alloyed steels. Methods for determination of tungsten

GOST 12350-78: Alloyed and high-alloyed steels. Methods of chromium determination

GOST 12351-2003: Alloyed and highalloyed steels. Methods for determination of vanadium

GOST 12351-81: Steels alloyed and highalloyed. Methods for the determination of vanadium

GOST 12352-81: Steels alloyed and highalloyed. Methods for the determination of nickel

GOST 12354-81: Steels alloyed and highalloyed. Methods for the determination of molybdenum

GOST 12355-78: Alloyed and high-alloyed steels. Methods of copper determination

GOST 12356-81: Steels alloyed and highalloyed. Methods of the determination of titanium

GOST 12357-84: Steels alloyed and highalloyed. Methods for the, determination of aluminium

GOST 12358-2002: Alloyed and highalloyed steels. Methods for determination of arsenic

GOST 12359-99: Carbon, alloyed and high-alloyed steels. Methods for determination of nitrogen

GOST 12360-82: Steels alloyed and highalloyed. Methods for the determination of boron

GOST 12361-2002: Alloyed and highalloyed steels. Methods for determination of niobium

GOST 12362-79: Alloy and high-alloy steels. Methods for determination of stibium, lead, tin, zinc and cadmium

GOST 14637-89: Thick sheet rolled stock of normal quality carbon steel

GOST 1497-84: Metals. Methods of tension test

GOST 162-90: Depth gauges. Specifications

GOST 16523-97: Rolled sheets from quality and ordinary carbon steel for general purposes. Specifications

GOST 166-89: Vernier callipers. Specifications

GOST 17745-90: Steels and alloys. Methods for determination of gases

GOST 18360-93: Plate snap-gauges for diameters from 3 to 260 mm. Dimensions

GOST 18365-93: Plate snap-gauges with changeable lips for diameters over 100 to 360 mm. Dimensions

GOST 18442-80: Non-destructive testing. Capillary methods. General requirements

GOST 18895-97: Steel. Method of photoelectric spectral analysis

GOST 19281-89: Rolled steel with increased strength. General specifications

GOST 19903-74: Hot-rolled steel sheets. Dimensions

GOST 21105-87: Non-destructive testing. Method of magnetic particle testing

GOST 2216-84: Adjustable smooth snap gauges

GOST 22536.0-87: Carbon steel and unalloyed cast iron. General requirements for methods of analysis

GOST 28033-89: Steel. Method of X-ray-fluorescent analysis

GOST 30415-96: Steel. Non-destructive testing of mechanical properties and microstructure of steel products by magnetic method

GOST 30432-96: Metal tubes. Selection of samples, tube stocks and specimens for mechanic and technological tests

GOST 30456-97: Metal production. Rolled steel and tubes. Methods of blow bending tests

GOST 380-94: Normal quality carbon steel

GOST 3845-75: Metallic tubes. Hydraulic pressure testing method

GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications

GOST 5378-88: Vernier protractors. Specifications

GOST 6507-90: Micrometers. Specifications

GOST 6996-66: Welded joints. Methods of mechanical properties determination

GOST 7502-98: Measuring metal tapes. Specifications

GOST 7565-81: Iron, steel and alloys. Sampling for determination of chemical composition

GOST 8.315-97: Standard samples for composition and properties of substances and materials

GOST 8.563.1-97: Measurement of liquids and gases flow rate and quantity by differential pressure method orifice plates, nozzles isa 1932 and ventury tubes inserted in circular cross-section filled conduits.

GOST 8.563.2-97: Measurement of liquids and gases flow rate and quantity by differential pressure method measurement procedure by orifice instruments official edition

GOST 8.563.3-97: Procedure and module of calculations software

GOST 8.586.1-2005: State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 1. Principle of the method of measurements and general requirements

GOST 8.586.2-2005: State system for ensuring the uniformity of measurements. Measurement of liquids and gases flow rate and quantity by means of orifice instruments. Part 2. Orifice plates. Technical requirements

GOST 8.586.3-2005: State system for ensuring the uniformity of measurements. Measurement of liquids and gases flow rate and quantity by means of orifice instruments. Part 3. Nozzles and Venturi nozzles. Technical requirements

GOST 8.586.4-2005: State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 4. Venturi tubes. Technical requirements

GOST 8.586.5-2005: State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 5. Measurement procedure

GOST 8695-75: Tubing (pipes). Flattening testing method

GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature

GOST R 8.568-97: State system for ensuring the uniformity of measurements. Verification of testing equipment. General principles

GOST R ISO 10124-99: Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes. Ultrasonic testing for the detection of laminar imperfections

GOST R ISO 10332-99: Seamless and welded ( except submerged arc-welded) steel tubes for pressure purposes. Ultrasonic testing for the verification of hydraulic leak-tightness

GOST R ISO 10543-99: Seamless and hot-stretch-reduced welded steel tubes for pressure purposes. Ultrasonic thickness testing

The Document is Referenced By:

GOST 31447-2012: Steel weldes pipes for trunk gas pipelines, oil pipelines and oil products pipelines. Specifications

GOST R 52568-2006: Steel pipes with defensive covering for main gas and oil pipelines. Specifications

GOST R 53384-2009: Steel and cast iron tubes and pipes with protective coatings. Technical requirements

GOST R 53675-2009: National standard of the Russian Federation. Pumps for the trunk oil pipelines. General Requirements

GOST R 53676-2009: Filters for the trunk oil pipelines. General requirements

GOST R 54929-2012: Steel welded pipes for general purposes. Specifications

GOST R 55436-2013: Gas distribution systems. Coatings with extruded polyethylene on steel pipes. General technical requirements

GOST R 56001-2014: Pipeline valves for objects of gas industry. General specifications

GOST R 8.637-2007: State system for ensuring the uniformity of measurements. Certified reference materials for metrological maintenance of pipeline non-destructive testing equipment. General requirements

GOST R ISO 3183-2009: Steel pipes for pipelines of petroleum and natural gas industries. General specifications

GOST R ISO 3183-2-2007: Steel pipes for pipelines. Specifications. Part 2. Requirements for class B pipes

GOST R ISO 3183-3-2007: Steel pipes for pipelines. Specifications. Part 3. Requirements for class C pipes

ST TsKBA 013-2007: Pipe fittings. Welding of fittings to the pipeline. Technical requirements

TU 1390-007-86695843-2010: Electrowelded steel pipes with a diameter of up to 1,420 mm with an external anti-corrosion polyethylene coating for the construction of field and main oil pipelines

TU 1390-014-86695843-2011: Steel pipes and parts of pipelines with external two-layer epoxy anticorrosion coating

TU 1390-015-86695843-2011: Steel pipes with Stelrant external anticorrosion polyurethane coating

TU 1394-006-86695843-10: Steel pipes with epoxy protective coating

TU 1394-011-86695843-2011: Steel pipes with an external two-layer epoxy coating resistant to ultraviolet radiation. Technical conditions

TU 146930-08-01297858-05: Specifications for cold bending curves from steel electric-welded pipes with diameters of 530 and 1220 mm with insulating coating for main pipelines

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English
Price: $745.00
imgalt
Unified system for design documentation. Types and sets of design documentation
Language: English
Price: $139.00
imgalt
Loads and impacts
Language: English
Price: $306.00
imgalt
High strength rolled steel. General specification
Language: English
Price: $289.00
imgalt
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English
Price: $349.00
imgalt
Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads
Language: English
Price: $311.00
imgalt
Articulated connector devices with cast male and female parts for freight cars of articulated type. General technical specifications
Language: English
Price: $333.00
imgalt
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English
Price: $414.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!