GOST 25812-83
ГОСТ 25812-83
|
|
Steel pipe mains. General requirements for corrosion protection
Трубопроводы стальные магистральные. Общие требования к защите от коррозии
Status: Not effective - Canceled in the Russian Federation. IUS 7-1998
The standard establishes the general requirements for the protection of facilities from underground and atmospheric corrosion of main oil, gas and product pipelines and outlets from them (hereinafter referred to as trunk pipelines); pipelines of compressor, gas distribution, pumping and pumping stations and headworks of fields (hereinafter referred to as the communications network); casing of wells and pipelines of oil and gas fields, underground gas storages and gas and oil complex treatment plants (hereinafter referred to as field facilities) and collectively referred to hereafter as structures for their underground, underwater (with dredging in the bottom), ground (with backfilling ) and aboveground gaskets. The standard does not apply to heat pipelines, steel water pipes, and structures laid in settlements, permafrost soils and in water bodies without penetration into the bottom.
Стандарт устанавливает общие требования к защите сооружений от подземной и атмосферной коррозии магистральных нефте-, газо- и продуктопроводов и отводов от них (далее в тексте - магистральные трубопроводы); трубопроводов компрессорных, газораспределительных, перекачивающих и насосных станций и головных сооружений промыслов (далее в тексте - сети коммуникаций); обсадных колонн скважин и трубопроводов нефтегазопромыслов, подземных хранилищ газа и установок комплексной подготовки газа и нефти (далее в тексте - промысловые объекты) и все вместе именуемые далее в тексте - сооружения при их подземной, подводной (с заглублением в дно), наземной (с засыпкой) и надземной прокладках. Стандарт не распространяется на теплопроводы, стальные водопроводы, и сооружения, проложенные в населенных пунктах, многолетнемерзлых грунтах и в водоемах без заглубления в дно.
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
5/27/1983
SKU: RUSS18696
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
23 Hydraulic and pneumatic systems and components for general use. »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.10 Cast iron and steel pipes »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.10 Cast iron and steel pipes »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G1 General parts and units of machines »
G18 Fittings and pipeline connections »
National Standards for OKSTU »
SYSTEMS OF GENERAL TECHNICAL AND ORGANIZATIONAL-METHODOLOGICAL STANDARDS »
Unified system of protection against corrosion and aging of materials and products (ESZKS) »
The Document References:
GOST 12.0.004-79: Occupational safety standards system. Labour safety worker training organization. General principles
GOST 12.1.003-83: Noise. General safety requirements
GOST 12.1.005-76: Occupational safety standards system. Working zone air. General hygiene requirements
GOST 12.2.004-75: Occupational safety standards system. Special machines and devices for pipe-line building. Safety requirements
GOST 12.2.007.0-75: Occupation safety standards system Electrical equipment. General safety requirements
GOST 12.3.005-75: Painting works
GOST 12.3.008-75: Production of metallic and non-metallic inorganic coatings
GOST 13073-77: Zinc wire
GOST 14254-80: Electrotechnical articles. Enclosures. Degrees of protections. Designations. Test methods
GOST 15140-78: Paintwork materials. Methods for determination of adhesion
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15836-79: Bitumen-rubber insulating mastic. Specifications
GOST 16149-70: Protection of underground structures against stray current corrosion by polarized protectors. Technical requirements
GOST 16337-77: High-pressure polyethylene. Specifications
GOST 16338-85: Low-pressure polyethylene. Specifications
GOST 16783-71: Plastics. Method of determining the brittleness temperature at squeezing the specimen folded up as a loop
GOST 23511-79: Industrial radio frequency interference generated by domestic electrical appliances used in residential buildings, or connected to domestic power sources
GOST 270-75: Rubber. Method of the determination elastic and tensile stress-strain properties
GOST 4233-77: Reagents. Sodium chloride. Specifications
GOST 6433.2-71: Solid electrical insulating materials. Methods for evaluation of electrical resistance at d. c. voltages
GOST 7871-75: Aluminum and aluminium alloy welding wire
GOST 9.015-74: Unified system of corrosion and ageing protection. Underground constructions. General technical requirements
GOST 9.032-74: Unified, system of corrosion and ageing protection. Paint coatings. Groups, technical requirements and designations
GOST 9.104-79: Unified system corrosion of corrosion and ageing protection. Paint coatings. Croups of operation conditions
The Document is Referenced By:
Decision 162: On the list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis ensures compliance with the requirements of the technical regulations of the Eurasian Economic Union "On requirements for main pipelines for the transportation of liquid and gaseous hydrocarbons (TR EAEU 049/2020), and the list of international and regional (interstate) standards, and in their absence - national (state) standards that contain rules and methods of research (tests) and measurements, including sampling rules necessary for the application and implementation of the requirements of technical regulation of the Eurasian Economic Union "On requirements for pipelines for the transportation of liquid and gaseous hydrocarbons (TR EAEU 049/2020) and conformity assessment of technical regulation objects
GOST 31445-2012: Steel and cast iron tubes and pipes with protective coatings. Technical requirements
GOST 31448-2012: Steel pipes with defensive covering for main gas and oil pipelines. Specifications
GOST 34027-2016: Gas supply system. Gas main pipeline transportation. Mechanical safety. Assigning of safe operation life for linear part of gas main pipeline
GOST 34181-2017: Trunk pipelines for oil and oil products transportation. Technical diagnosis. Main principles
GOST 34182-2017: Oil and оil рroducts trunk pipeline transportation. Operation and maintenance. General principles
GOST 34597-2019: Anode grounding of installations of electrochemical protection against corrosion of underground metal structures. Methods for determining the biocorrosive aggressiveness of soils and their impact on underground metal structures
GOST 9.015-74: Unified system of corrosion and ageing protection. Underground constructions. General technical requirements
GOST 9.602-2005: Unified system of corrosion and ageing protection. Underground constructions. General requirements for corrosion protection
GOST 9.602-2016: Unified system of corrosion and ageing protection. Underground constructions. General requirements for corrosion protection
GOST 9.602-89: Constructions, underground. General requirements for corrosion protection
Manual for SNiP 3.05.02-88: Manual on technology and organization of the construction of pipelines for gas supply systems in rural areas of the Non-chernozem zone of the RSFSR
ONTP 1-86: All-union regulations of technological engineering of liquefied petroleum gas extraction plants
ONTP 51-1-85: National Engineering Design Standards. Trunk Pipelines. Part I: Gas Pipelines
PB 03-108-96: Process pipeline design and safe operation rules
PB 11-401-01: Safety regulations for gas-handling facilities of metallurgic and coke-chemical industries and enterprises
R 625-87: Method of calculating single indicators of corrosion reliability of the linear part of the pipeline
RD 153-112TNP-027-97: Guidelines for Cold-Weather Overhaul of Petroleum Product Pipelines 100-720 mm in Diameter
RD 153-39.4-039-99: Standards for the design of electrochemical protection of trunk pipelines and MN sites
RD 153-39.4-041-99: Operating rules and regulations for trunk oil product pipelines.
RD 153-39.4-044-99: Rules of total overhaul of main oil product pipelines laid in the cities, settlements and entering the territory of tank farms and pumping stations
RD 153-39.4-075-01: Rules of maintenance overhaul of oil-trunk pipeline at waterway, railway and category I-IV highway crossings.
RD 153-39.4-113-01: Standards for technological design of main pipelines
RD 34.20.132: Guidelines for Electrochemical Corrosion Protection of Underground Energy Industry Structures
RD 39-00147105-015-98: Rules of total overhaul of main oil pipelines
RD 39-0147103-344-86: Rules for technical operation of collection systems and intra-field transport of oil and gas
RD 39-0147103-345-86: Instructions for control during construction, acceptance and operation of underwater crossings of main oil pipelines
RD 39-0147103-346-86: Process Guidelines for Overhaul of Underground 1220-mm Petroleum Pipelines Using Available Technical Means
RD 39-0147103-358-89: Instruction on the process of overhaul of underwater oil pipelines by the method of grafting on category I-III soils using existing technical means
RD 39-0147103-372-86: Instructions for inspection of the corrosion state of trunk pipelines
RD 39-132-94: Regulations for Operation, Inspection, Repair and Rejection of the Field Pipelines 1994
RD 39-135-94: Norms for technological design of gas-processing plants
RD 39-30-1197-84: Guidance Document. Methods of inspection of the technical condition of sections of trunk pipelines laid in the marshes
RD 50-541-85: Guidelines for the implementation of the standards of the Unified System for the Protection of Products and Materials Against Corrosion, Aging and Biodeterioration (ESHSC) in industries
RD 51-129-87: Methodical instructions for the calculation of the norms of consumption and the need for electricity for the technological needs of the electrochemical protection services of gas pipelines and gas-field equipment
RD 51-2.4-007-97: Protection of Soils against Water Erosion in Locations of Linear Sections of Pipelines
RD 51-3-96: Regulations for the maintenance of underwater crossings of main gas pipelines through water barriers
RD 51-553-94: Instructions for technical certification of gas accumulators GSS-1-1-10,0-25U-001 during the operation of gas filling stations of gas compressor stations (AGNKS)
SNiP 2.05.13-90: Oil-product pipelines laid on the territories of cities and other settlements
SP 106-34-96: SPSMG. Code of Practice on the construction of the linear part of the pipeline. Laying of gas pipes with prefabricated insulation. RAO "Gazprom", 01/10/96
SP 34-116-97: Instructions For Design, Construction and Redesign of Field Oil and Gas Pipelines
STN 51-4-92: Construction of Underwater Crossings of Pipelines by Trenchless Method
VI 006-91: Temporary instruction. Technical standards for the design and implementation of anticorrosive protection of oil pipelines of the Middle Ob region
VNTP 2-86: Engineering design standards for crude oil transmission pipelines
VNTP 3-85: Norms of process design of facilities for gathering transport and treatment of oil gas and water of oil fields
VNTP 3-90: Engineering Design Standards for Branched Petroleum Product Pipelines
VRD 39-1.10-005-2000: Ordinance on Operation of Gas Distribution Stations of Trunk Gas Pipelines
VRD 39-1.10-006-2000*: Rules for the technical operation of gas pipelines
VSN 005-88: Construction of field steel pipelines Technology and arrangement
VSN 008-88: Construction of trunk and field pipelines. Anticorrosion and heat insulation
VSN 009-88: Construction of main and commercial pipelines. Means and installations of cathodic protection.
VSN 012-88: Main pipeline and flowline construction. Quality control and commissioning of works
VSN 013-88/Minneftegazstroj: Construction of main and field pipelines in permafrost
VSN 210-87: Instructions for the use of a complex of devices for non-destructive testing of the integrity of the insulating coatings of buried pipelines
VSN 39-1.10-001-99: Guidelines for the Use of Composite Materials for the Repair of Defective Pipes of Trunk Gas Pipelines
VSN 4-94: Industry-Specific Building Code for Installation of Heating Supply Networks with Pipes Insulated with Cold-Applied Heat-Resistant Bitumen-Rubber Mastic
VSN 51-1-97: Work Execution Requirements for Overhaul of Trunk Pipelines
VSN 51-3-85: Design of field steel pipelines
VSN 51-9-86: Design of offshore underwater oil and gas pipelines
VSN 53-96: Guidelines for the Application of Heat-Shrinking Couplings and Tapes for Pipe Joint Insulation
VSN 63-97: Industry-Specific Building Code for Construction of Gas Supply and Water Supply Networks Made of Polyethylene-Coated Pipes 57-2020 mm in Diameter
|
Customers Who Viewed This Item Also Viewed:
 |
Limit dimension deviation from 0,1 to 10000 mm and surface shape and arrangement allowances, not specified on drawings.
Language: English |
Rules of development, coordination, approval and composition of technical and economic assessment for construction
Language: English |
Mineral fertilizers. Method for determination of dynamic strength and attrition
Language: English |
Diesel fuel EURO. Specifications
Language: English |
Inch thread with a profile angle of 55 degrees
Language: English |
Vessels and apparatus. Norms and methods of strength calculation. General requirements
Language: English |
Norms of structural design of nuclear power plants with reactors of different types
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
