GOST R 52630-2006
ГОСТ Р 52630-2006
|
|
Steel welded vessels and apparatus. General specifications
Сосуды и аппараты стальные сварные. Общие технические условия
Status: Not effective - Superseded. Registration information 1637-st dated November 29, 2012 (official website of Rosstandart); IUS 4-2013
The standard applies to steel welded vessels and apparatus operating under a pressure of not more than 16 MPa (160 kgf
Стандарт распространяется на стальные сварные сосуды и аппараты, работающие под давлением не более 16 МПа (160 кгс/см2.), вакуумом с остаточным давлением не ниже 665 Па (5 мм рт. ст.) или без давления (под налив) и при температуре стенки не ниже минус 70 град. Цельсия, предназначенные для применения в технологических установках химической, нефтехимической, нефтеперерабатывающей, нефтяной, газовой и других смежных отраслях промышленности. Стандарт устанавливает основные технические требования к конструкции, материалам, изготовлению (доизготовлению), методам испытаний, приемке и поставке, реконструкции, ремонту, монтажу сосудов и аппаратов. Стандарт не распространяется на: - сосуды, работающие под вакуумом с остаточным давлением ниже 665 Па (5 мм рт. ст.); - сосуды, предназначенные для транспортирования нефтяных и химических продуктов; - баллоны для сжатых, сжиженных и растворенных газов; - трубчатые печи; - резервуары (емкости) для хранения химических и нефтяных продуктов, проектируемые в соответствии со строительными нормами и специальными правилами.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/27/2006
SKU: RUSS19582
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
71 Chemical industry »
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Welding materials »
Welding regulations »
Welding staff »
Welding regulations »
Admission Testing »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Defects »
Welding regulations »
Welding work »
Manual welding »
Welding regulations »
Welding work »
Surfacing »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Main materials »
Non-ferrous metals »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.13 Testing and control of products of engineering industry »
4.13.1 Machinery, equipment and components for general engineering applications »
4.13.1.9 Equipment for centrifugal and gravity separation of liquid and non-uniform systems »
ISO classifier »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
71.120.01 Equipment for chemical industry as a whole »
National standards »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
71.120.01 Equipment for chemical industry as a whole »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G4 Machinery and equipment for heavy industry »
G40 Classification, nomenclature and general rules »
The Document is Replaced With:
GOST R 52630-2012: Steel welded vessels and apparatus. General specifications.
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 10092-2006: Cupro-nickel tubes for heat-exchange apparatus. Specifications
GOST 10198-91: Wooden boxes for weights of mass over 200 up to 20000 kg. General specifications
GOST 10494-80: Studs for flanged connections with lens-shaped seals for pn - 10-100 MPa (100-1000 kgf/sq sm). Technical requirements
GOST 10495-80: Hexagon nuts for flange joints for pn above 10 to 100 MPa (above 100 to 1000 kgf/cm2)
GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications
GOST 10702-78: Steel bars, carbon and alloy, structural, for cold extruding and upsetting. Specifications
GOST 10706-76: Electrically welded steel line-weld tubes. Technical requirements
GOST 10885-85: Hot-rolled two-ply corrosion-resistant steel sheets
GOST 11036-75: Electrotechnical quality unalloyed steel. Specifications
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.1.007-76: Noxious substances. Classification and general safety requirements
GOST 12620-78: Conical heads without knuckle, apex angles 60, 90 and 120 degrees. Basic dimensions
GOST 12621-78: Conical heads without knuckle, apex angle 140 degrees. Basic dimensions
GOST 12622-78: Flat heads witch knuckle. General dimensions
GOST 12623-78: Flat neads without knuckle. General dimensions
GOST 12816-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). General technical requirements
GOST 12971-67: Rectangular plates for machines and devices. Dimensions
GOST 14192-96: Cargo marking
GOST 14637-89: Thick sheet rolled stock of normal quality carbon steel
GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 1525-91: Rods of monel. Specifications
GOST 15527-2004: Pressure treated copper zinc alloys (brasses). Grades
GOST 1577-81: Rolled sheets and wide strips of structural quality steel. Specifications
GOST 1577-93: Plate and broadband roll stock of construction fine steel.
GOST 17217-79: Copper-nickel alloyed tubes grade Mnzh 5-1
GOST 17232-79: Aluminium and aluminium alloys plates. Technical conditions
GOST 17232-99: Aluminium and aluminium alloys plates. Specifications
GOST 17314-81: Devices for fastening thermal insulation of steel vessels and equipment. Design and dimensions. Technical requirements
GOST 17375-2001: Carbon and low-alloy steel butt-welding fittings. Sharply curved bends type 3D (R=1,5 DN). Design
GOST 17380-2001: Carbon and low-alloy steel butt-welding fittings. General specifications
GOST 17711-80: Cast copper-zinc alloys (brass)
GOST 17711-93: Cast copper-zink alloys (brass). Grades
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 18475-82: Cold-worked aluminum and aluminum alloy pipes
GOST 18482-79: Aluminium and aluminium alloy extruded pipes. Specifications
GOST 18661-73: Steel. Method for measurement of hardness by shock indentation
GOST 18968-73: Corrosion-resistant and high temperature steel rods and strips for steam turbine blades
GOST 19.402-78: Unified system for program documentation. Program description
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 19903-74: Hot-rolled steel sheets. Dimensions
GOST 2.601-2006: Unified system for design documentation. Exploitative documents
GOST 20072-74: Heat-resistant steel
GOST 20700-75: Bolts, studs, nuts and washers for flanged and anchor connections, corks and yokes with medium temperature from 0 to 650 °C. Specifications
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 21488-76: Extruded bars of aluminium and aluminium alloys
GOST 21488-97: Pressed bars of aluminium and aluminium alloys. Specifications
GOST 21631-76: Sheets of aluminium and aluminium alloys. Specifications
GOST 21646-2003: Copper and brass tubes for heat-exchange apparatus. Specifications
GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements
GOST 22727-88: Rolled sheet. Ultrasonic test methods
GOST 23055-78: Non-destructive testing. Fusion welding of metals. Welds classification by radiography testing results
GOST 23304-78: Bolts, studs, nuts and washers for flanged connections for atomic power plants. Technical requirements. Acceptance. Test methods. Marking, packing, transportation and storage
GOST 24634-81: Wooden boxes for export products. General specifications
GOST 24643-81: Basic norms of interchangeability. Tolerances of form and position of surfaces. Numerical values
GOST 25054-81: Forgings made of corrosion-resistant steels and alloys
GOST 25347-82: Basic norms of interchangeability. Unified system of tolerances and fits. Tolerance zones and recommendable fits
GOST 26.008-85: Lettering for inscriptions applied by engraving method. Executive dimensions
GOST 26.020-80: Types for means of measuring and automation. Inscription and main dimensions
GOST 26179-84: Basic norms of interchangeability. Tolerances for sizes above 10000 up to 40000 mm
GOST 26364-90: Ferritometers for austenitic steels. General specifications
GOST 26828-86: Instrumentation and machine building products. Marking
GOST 28759.5-90: Flanges of vessels and apparatuses
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 3242-79: Welded joints
GOST 3262-75: Water-supply and gas-supply steel pipes Technical conditions
GOST 356-80: Valves and details for piping. Pressures conditional, test and operational. Lines.
GOST 380-2005: Common quality carbon steel. Grades
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 4543-71: Structural alloyed steel
GOST 4784-74: Wrought aluminium and aluminium alloys. Grades
GOST 4784-97: Aluminium and wrought aluminium alloys. Grades
GOST 492-2006: Nickel, nickel and copper-nickel alloys treated by pressure. Grades
GOST 494-90: Pipes of brass
GOST 5063-73: Ribbons of cupro-nickel alloys. Specifications
GOST 535-2005: Common quality carbon steel bar and shaped sections. General specifications
GOST 550-75: Seamless steel tubes for petroleum processing and petrochemical industry. Specifications
GOST 5520-79: Carbon, low-alloy and alloy sheet steel for boilers and pressure vessels. Specifications
GOST 5521-93: Shipbuilding rolled steel
GOST 5582-75: Corrosion-resistant, heat-proof, and heat-resistant thin-sheet rolled stock
GOST 5632-72: High-alloy steels and corrosion-proof, heat-resisting and heat treated alloys. Grades
GOST 5949-75: Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
GOST 5959-80: Uncollapsable wooden sheet material boxes for weights to 200 kg mass. General specifications
GOST 6032-2003: Corrosion-resistant steels and alloys. Test methods of intercrystalline corrosion resistance
GOST 6533-78: Ellipsoidaldished heads flanged made of steel for vess els apparatus and boilers. Basis dimensions
GOST 6996-66: Welded joints. Methods of mechanical properties determination
GOST 7350-77: Plate, corrosion-resistant, heat-resistant, and high-temperature steel
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 8479-70: Structural carbon and alloy steel forgings
GOST 8724-2002: Basic norms of interchangeability. Metric screw threads. General plan
GOST 8731-74: Seamless hot-deformed steel pipes. Specifications
GOST 8733-74: Cold-formed and heat-formed seamless steel pipes. Technical requirements
GOST 9.014-78: Unified system of corrosion and ageing protection. Temporary corrosion protection of products. General requirements
GOST 9.402-2004: Unified system of corrosion and ageing protection. Paint coatings. Metal surface preparation for painting
GOST 9012-59: Metals. Method of Brinell hardness measurement
GOST 9013-59: Metals. Method of measuring Rockwell hardness
GOST 9045-93: Cold-rolled thin sheets of low-carbon steel for cold stamping. Specifications
GOST 931-90: Brass sheets and strips. Specifications
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST 9617-76: Vessels and apparatus. Series of diameters.
GOST 977-88: Steel castings. General specifications
GOST 9940-81: Seamless hot-deformed tubes made from corrosion-resistant steel
GOST 9941-81: Seamless cold- and warm-deformed tubes made from corrosion-resistant steel
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 12.4.026-2001: Occupational safety standards system. Safety colors, safety signs and signal marking. Purpose and rules of application. General technical requirements and characteristics. Test methods
GOST R 2.901-99: Unified system for design documentation. Documentation to be sent abroad. General requirements
GOST R 50460-92: Mark of conformity for obligatory certification form, dimensions dnd technical requirements
GOST R 52627-2006: Bolts, screws and studs. Mechanical properties and test methods
OST 108.030.113-87: Carbon and alloy steel forgings for thermal and nuclear power stations equipment and pipelines. Technical specifications.
OST 26-01-135-81: Vessels, devices and high-pressure pipeline parts forgings. General technical requirements, acceptance rules, Test methods.
OST 26-07-402-83: Steel castings for pipeline fittings and driving gears to it. General specifications.
OST 26-291-94: Steel welded vessels and devices. General technical requirements.
PB 03-576-03: Regulations of design and safe operation of pressure vessels
TU 14-3-1573-96: Steel electric welded longitudinal pipes with a diameter of 530-1020 mm with a wall thickness of up to 32 mm for main gas pipelines, oil pipelines and oil product pipelines
The Document is Referenced By:
ATK-RE 2011: Shell and tube heat exchangers and "pipe in pipe" heat exchangers. Manual
ATK-RE 2013: Shell-and-tube heat exchangers and pipe-in-tube heat exchangers manufactured according to TU 3612-005-00220302, TU 3644-006-00220302, TU 3612-017-00220302, TU 3612-013-00220302, TU 3612-014-00220302, TU 3612-013 023-00220302, TU 3612-024-00220302, TU 3612-100-00220302. Manual
ATK-RE 2015: Shell-and-tube heat exchangers and tube-in-tube heat exchangers. Manual
GOST R 51365-2009: Petroleum and natural gas industries. Drilling and production equipment. Wellhead and Christmas tree equipment. General specifications
GOST R 52630-2012: Steel welded vessels and apparatus. General specifications.
GOST R 52857.11-2007: Vessels and apparatus. Norms and methods of strength calculation. Method of strength calculation of shells and heads according to weld misalignment, angular misalignment and shell nonroundness
GOST R 52857.1-2007: Vessels and apparatus. Norms and methods of strength calculation. General requirements
GOST R 52857.3-2007: Vessels and apparatus. Norms and methods of strength calculation. Reinforcement of openings in shells and heads under internal and external pressure. Strength calculation of shells and heads under external static loads on the nozzle
GOST R 52857.4-2007: Vessels and apparatus. Norms and methods of strength calculation. Stength and leak-tightness calculation of flange joints
GOST R 53677-2009: Petroleum and natural gas industries. Shell-and-tube heat eхchangers. Technical requirements
GOST R 53681-2009: Flare parts for general refinery and petrochemical service. General technical requirements
GOST R 53684-2009: Columns. Technical requirements
GOST R 54892-2012: Installation of air separation plants and other cryogenic equipment. General provisions
OST 26.260.480-2003: Two-ply steel vessels and devices. Welding and weld deposition.
RD 03-29-93: Instructional Guidelines For Engineering Certification of Steam and Hot-Water Boilers, Pressure Vessels, Steam and Hot-Water Pipelines
RMG 116-2011: State system for ensuring the uniformity of measurements. Tanks of main oil lines and oil storage depots. Maintenance operations and metrological assurance under operating conditions
STO SA 03.003-2009: Vessels and apparatus. Norms and methods of strength calculation. Calculation of seismic effects
TU 3113-028-00220302-01: Heaters of steam and water-to-water for heating networks of heating and hot water systems. Technical conditions
TU 3612-023-00220302-01: Shell-and-tube heat exchangers with a floating head, shell-and-tube with U-tubes and tube bundles for them
TU 3612-024-00220302-02: Shell and tube heat exchangers with fixed tube sheets and shell and tube with temperature compensator on the shell
TU 3615-132-00220302-2008: Ball tanks for liquefied petroleum gases. Specifications
TU 3644-006-00220302-99: Shell-and-tube heat exchangers for special purposes. Refrigeration evaporators and condensers
Customers Who Viewed This Item Also Viewed:
|
Limit dimension deviation from 0,1 to 10000 mm and surface shape and arrangement allowances, not specified on drawings.
Language: English |
Vessels and apparatus. Norms and methods of strength calculation. General requirements
Language: English |
Norms of structural design of nuclear power plants with reactors of different types
Language: English |
Mineral fertilizers. Method for determination of dynamic strength and attrition
Language: English |
Diesel fuel EURO. Specifications
Language: English |
Inch thread with a profile angle of 55 degrees
Language: English |
|
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.