imgalt

OST 26-291-94

ОСТ 26-291-94

Steel welded vessels and devices. General technical requirements.

Сосуды и аппараты стальные сварные. Общие технические условия

Status: Not effective

The standard applies to steel welded vessels and apparatus operating under a pressure of not more than 16 MPa (160 kgf

Стандарт распространяется на стальные сварные сосуды и аппараты, работающие под давлением не более 16 МПа (160 кгс/см2) или без давления (под налив) при температуре стенки не ниже -70 град. Цельсия. Стандарт не распространяется: на сосуды с толщиной стенки более 120 мм; на сосуды, работающие под вакуумом с остаточным давлением ниже 665 Па (5 мм. рт. ст.); на сосуды, предназначенные для транспортирования нефтяных и химических продуктов; на баллоны для сжатых и сжиженных газов; на аппараты военных ведомств; на трубчатые печи.

Choose Language: 
Format: Electronic (pdf/doc)

Approved: RF Committee on Mechanical Engineering, 4/21/1994

SKU: RUSS19659

Price: $745.00

imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Industry Standards and Specifications » Industry standards »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.12 Testing and control of products of metallurgical industry » 4.12.6 Metal products »

ISO classifier » 23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS » 23.020 Storage tanks for liquids and gases » 23.020.01 Storage tanks for liquids and gases in general »


As a Replacement Of:

OST 26.291-87: Welded vessels and apparatus. General technical conditions

OST 26-02-2081-85: Steel welded vessels and apparatuses. Additional technical requirements for export supplies

The Document References:

ATK 24.200.03-90: Support Racks for Upright Apparatus. Types, Design, and Dimensions

ATK 24.200.04-90: Supports for Cylindrical and Conical Upright Apparatus. Types and Basic Parameters

GOST 10006-80: Metal pipes

GOST 10198-91: Wooden boxes for weights of mass over 200 up to 20000 kg. General specifications

GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications

GOST 10605-94: Hexagon nuts with thread diameter over 48 mm. Product grade B. Specifications

GOST 10706-76: Electrically welded steel line-weld tubes. Technical requirements

GOST 10885-85: Hot-rolled two-ply corrosion-resistant steel sheets

GOST 11650-80: Self-tapping round-head and sharpening end screws for metals and plastics. Design and dimensions

GOST 12.1.005-88: General sanitary requirements for working zone air

GOST 12.1.007-76: Noxious substances. Classification and general safety requirements

GOST 12.4.026-76: Signal colors and safety signs

GOST 12619-78: Conical heads with knuckle, apex angles 60 and 90 degrees. Basic dimensions

GOST 12620-78: Conical heads without knuckle, apex angles 60, 90 and 120 degrees. Basic dimensions

GOST 12621-78: Conical heads without knuckle, apex angle 140 degrees. Basic dimensions

GOST 12622-78: Flat heads witch knuckle. General dimensions

GOST 12623-78: Flat neads without knuckle. General dimensions

GOST 12815-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). Types. Connecting dimensions and dimensions of sealing surfaces

GOST 12816-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). General technical requirements

GOST 12817-80: Cast grey iron flanges for Pnom from 0,1 to 1,6 MPa (from 1 to 16 kgf/sq sm). Design and dimensions

GOST 12818-80: Cast malleable iron flanges for Pnom from 1,6 to 4,0 MPa (from 16 to 40 kgf/cm2). Design and dimensions

GOST 12819-80: Cast steel flanges for Pnom from 1,6 to 20,0 MPa (from 16 to 200 kgf/sq sm). Design and dimensions

GOST 12820-80: Steel plane welded flanges for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/cm2). Design and dimensions

GOST 12821-80: Steel butt-welded flanges for Pnom from 0,1 to 20,0 MPa (from 1 to 200 kgf/cm2). Design and dimensions

GOST 12822-80: Steel loose flanges with welded ring for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/sq sm). Design and dimensions

GOST 12971-67: Rectangular plates for machines and devices. Dimensions

GOST 14192-96: Cargo marking

GOST 14637-89: Thick sheet rolled stock of normal quality carbon steel

GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods

GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence

GOST 1577-93: Plate and broadband roll stock of construction fine steel.

GOST 16032-70: Timber floating. Terms and definitions

GOST 17232-99: Aluminium and aluminium alloys plates. Specifications

GOST 17314-81: Devices for fastening thermal insulation of steel vessels and equipment. Design and dimensions. Technical requirements

GOST 17375-83: Seamless welded steel pipeline components for Pn £ 10 MPa (£ 100 kgf/cm2). Sharply curved offsets. Design

GOST 17380-83: Seamless welded steel pipeline components for Pn £ 10 MPa (£ 100 kgf/cm2). Specifications

GOST 19281-89: Rolled steel with increased strength. General specifications

GOST 19903-74: Hot-rolled steel sheets. Dimensions

GOST 2.601-95: Operational documents

GOST 20072-74: Heat-resistant steel

GOST 20700-75: Bolts, studs, nuts and washers for flanged and anchor connections, corks and yokes with medium temperature from 0 to 650 °C. Specifications

GOST 21631-76: Sheets of aluminium and aluminium alloys. Specifications

GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements

GOST 22465-88: Centrifugal booster pumps. Main parameters

GOST 2246-70: Welding steel wire. Specifications

GOST 23055-78: Non-destructive testing. Fusion welding of metals. Welds classification by radiography testing results

GOST 24379.0-80: Foundation bolts. General specification

GOST 24634-81: Wooden boxes for export products. General specifications

GOST 24660-81: Acceptance statistical inspection by attributes based on economic characters

GOST 25347-82: Basic norms of interchangeability. Unified system of tolerances and fits. Tolerance zones and recommendable fits

GOST 26901-86: Bide ceramic. Specifications

GOST 28759.2-90: Steel flat welded flanges of vessels and apparatus. Design and dimensions

GOST 28759.3-90: Steel butt welded flanges of vessels and apparatus. Design and dimensions

GOST 28759.4-90: Steel butt welded flanges of vessels and apparatus for gaskets of octangular sections. Design and dimensions

GOST 28759.5-90: Flanges of vessels and apparatuses

GOST 3242-79: Welded joints

GOST 3262-75: Water-supply and gas-supply steel pipes Technical conditions

GOST 356-80: Valves and details for piping. Pressures conditional, test and operational. Lines.

GOST 380-94: Normal quality carbon steel

GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications

GOST 4543-71: Structural alloyed steel

GOST 4784-97: Aluminium and wrought aluminium alloys. Grades

GOST 481-80: Compressed asbestos fibre sheets and gaskets from it. Specifications

GOST 494-90: Pipes of brass

GOST 535-88: Common quality carbon bar and shaped sections. General specifications

GOST 550-75: Seamless steel tubes for petroleum processing and petrochemical industry. Specifications

GOST 5520-79: Carbon, low-alloy and alloy sheet steel for boilers and pressure vessels. Specifications

GOST 5583-78: Industrial and medical gaseous oxygen

GOST 5632-72: High-alloy steels and corrosion-proof, heat-resisting and heat treated alloys. Grades

GOST 6102-94: Asbestos fabric

GOST 6368-82: Type R8, R11, R18 and R24 narrow-gauge railway rails. Design and dimensions

GOST 6533-78: Ellipsoidaldished heads flanged made of steel for vess els apparatus and boilers. Basis dimensions

GOST 6996-66: Welded joints. Methods of mechanical properties determination

GOST 7062-90: Carbon and alloyed steel forgings fabricated by press forging. Allowances and tolerances

GOST 7512-82: Nondestructive testing. Welded joints. Radiography method

GOST 7829-70: Carbon and alloyed steel forgings fabricated by hammer forging. Allowances and tolerances

GOST 8479-70: Structural carbon and alloy steel forgings

GOST 8724-81: Basic norms of interchangeability. Metric screw thread. Diameters and pitches

GOST 8731-74: Seamless hot-deformed steel pipes. Specifications

GOST 8733-74: Cold-formed and heat-formed seamless steel pipes. Technical requirements

GOST 9.014-78: Unified system of corrosion and ageing protection. Temporary corrosion protection of products. General requirements

GOST 9.402-80: Metal surface preparation for painting

GOST 9012-59: Metals. Method of Brinell hardness measurement

GOST 9045-93: Cold-rolled thin sheets of low-carbon steel for cold stamping. Specifications

GOST 9087-81: Welding melted fluxes

GOST 931-90: Brass sheets and strips. Specifications

GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature

GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications

GOST 9467-75: Metal covered electrodes for manual arc welding of structural and heat-resistant steels. Types

GOST 9617-76: Vessels and apparatus. Series of diameters.

GOST 977-88: Steel castings. General specifications

GOST 9940-81: Seamless hot-deformed tubes made from corrosion-resistant steel

GOST 9941-81: Seamless cold- and warm-deformed tubes made from corrosion-resistant steel

GOST R 50460-92: Mark of conformity for obligatory certification form, dimensions dnd technical requirements

OST 26-01-136-81: Assembling units of steel pipelines on pressure over 9,81 to 98,1 MPa (over 100 to 1000 kgf/cm2) of complete technological lines. General specifications.

OST 26-02-1015-85: Tube fastening to tube sheets.

OST 26-2043-91: Bolts, studs, nuts and washers for flanged joints. Technical requirements

RD 26-11-08-86: Welded Joints. Mechanical Tests

SNiP 2.01.01-82: Construction climatology and geophysics

The Document is Referenced By:

ATK 24.200.02-90: Album typical designs. Flanged steel plugs. Design, dimensions and specifications

ATK 24.202.09-2004: Shell-and-tube heat exchangers with a floating head and U-tubes, doubled. Main dimensions

ATK 24.202.10-2007: Album typical designs. Shell and tube heat exchangers with fixed tube sheets and shell and tube with temperature compensator on the shell. Blocks. Main dimensions

ATK 24.218.04-90: Liquid mesh filters for pipelines. Design, dimensions and dimensions

ATK 26-02-1-89: Direct-flow valve plates for column-type devices. Options. Construction and main dimensions

ATK 26-02-2-89: Four-flow straight valve plates for column-type apparatus. Options. Construction and main dimensions

ATK 26-02-3-89: Mesh plates with baffle elements for column type devices. Options. Construction and main dimensions

ATK 26-18-10-94: Devices for Installation of Temperature Measuring Devices for Use at Nominal Pressure from 0.6 to 16.0 MPa. Plugs. General Technical Requirements

ATK 26-18-11-96: The union screw and checkpoints. Design, dimensions and general technical requirements

ATK 26-18-13-96: Flanges for reinforcing connecting parts and pipelines for corrosive environments on Ru from 0.6 to 16.0 MPa. Design, dimensions and general technical requirements

ATK 26-18-14-98: Flanges of vessels and apparatus steel flat welded to a conditional pressure up to Ru 0.1 MPa. Design, dimensions and general technical requirements

ATK 26-18-5-93: Album typical designs. Steel turning plugs for rebar flanges. Design, dimensions and specifications

ATK-RE 2004: Shell and tube heat exchangers and "pipe in pipe" heat exchangers. Manual

DiOR 05: Methodology of diagnosing of technical condition and determining of residual life of process equipment of oil refineries and petrochemical plants

GOST 20680-2002: Mechanical mixing devices (agitated vessels). General specifications

GOST 31385-2008: Vertical cylindrical steel tanks for oil and oil-products. General specifications

GOST R 51738-2001: Biotechnical industries equipment. Vegetable materials hydrolysis apparatus. Fermenters. Safety requirements. Test methods

GOST R 52630-2006: Steel welded vessels and apparatus. General specifications

GOST R 52910-2008: Vertical cylindrical steel tanks for oil and oil-products. General specifications

ITN 93: Instructions for technical supervision, methods of audit and rejection of tube furnaces, tanks, vessels and apparatuses of oil refining and petrochemical industries

ITNJe-93: Instruction on technical supervision and operation of pressure vessels not covered by the Rules of Gosgortechnadzor

OST 108.271.101-76: Delivery water low-pressure heaters for thermal power plants, heating-industrial and heating boiler houses. Types. Main data. Design and dimensions. Technical requirements.

OST 24.200.02-91: Assembling units of steel pipelines on nominal pressure<=10 MPa (100 kgf/cm2) of complete technological lines. General specifications.

OST 26.260.14-2001: Pressure-operated vessels and devices. Leak check techniques.

OST 26.260.18-2004: Process modules for oil and gas industry. General technical specifications

OST 26.260.452-92: Occupational safety standards system. Rotor drum vacuum baking ovens in explosion-proof design. General safety requirements.

OST 26.260.462-99: Devices for installation of instruments measuring the temperature for PN from 0.6 to 16 MPa. Types, design, dimensions and general technical requirements

OST 26.260.472-2000: devices for installation of pressure gauges and pressure selection. General technical requirements.

OST 26.260.480-2003: Two-ply steel vessels and devices. Welding and weld deposition.

OST 26.260.758-2003: Metal structures. General technical requirements.

OST 26-01-1298-81: Flange of vessels and apparatuses made of titanium. Types, Design and dimensions. Strength and integrity calculation procedure.

OST 26-01-147-89: Drying devices with rotating drums. General technical requirements.Printing telegraph and terminals for document electric communication. Methods of printed character parameter measurement.

OST 26-01-1512-76: Axial lens compensators for PN <= 2,5 MPa (25 kgf / cm2). Technical requirements

OST 26-02-1015-85: Tube fastening to tube sheets.

OST 26-02-1496-76: Air, gas and liquid medium vessels and devices. Technical specifications.

OST 26-02-2053-79: Adapter and hatches made of double-layer steel. Technical requirements .

OST 26-02-376-78: Technological units of gas and oil industry. General technical requirements.

OST 26-02-757-79: Ladders. Design, dimensions and specifications.

OST 26-11-10-93: Welded joints. X-Ray TV testing method.

OST 26-1111-74: Plates TSK-RC, TSK-RB for column apparatus. Parameters, design and dimensions

OST 26-18-5-88: Technological units of gas and oil industry. General technical requirements.

OST 26-18-6-88: Vessels, Apparatus and Process Units, Operating at Temperature Below Minus 70°C. Technical requirements

OST 26-2011-83: Welded vessels and apparatus hatches. Technical requirements.

OST 26-2015-83: Hinge and tilt-up Devices for manhole covers of welded steel of vessels and apparatuses. Technical requirements .

OST 26-467-84: Cylindrical and conical supports for the vertical apparatus. Types and basic dimensions.

OTU 3-01: Vessels and apparatuses. General specifications for the repair of buildings

PB 03-110-96: Safety regulations on pressurized storage of liquefied petroleum gas and highly inflammable liquids

PB 09-297-99: Rules of setup and safe operation of compressor units with piston compressors operating on dangerously explosive and noxious gases

POT R M-015-2000: Intersectoral labor protection regulations for the operation of freon refrigeration units

RD 03-29-93: Instructional Guidelines For Engineering Certification of Steam and Hot-Water Boilers, Pressure Vessels, Steam and Hot-Water Pipelines

RD 03-380-00: Guidelines for Inspection of Spherical Tanks and Gas Holders for Storage of Liquefied Gases Under Pressure

RD 03-421-01: Guidelines for the diagnosis of the technical condition and the determination of the residual service life of vessels and apparatus

RD 09-244-98: Instructions for diagnostics of technical condition of vessels, pipes and compressors, industrial ammonia refrigeration plants.

RD 24.200.04-90: Weld seams. Metallographic method of control of the base metal and welded joints of chemical oil equipment

RD 24.200.11-90: Pressure-operated vessels and devices. Safety rules and standards during hydro-proof and leak-proof testing operations.

RD 24.200.13-90: Seamless steel pipes. Methodic of uniformity incoming ultrasonic control.

RD 24.942.02-90: Electroslag welding of chemical and petroequipment from low-alloyed and heat-resistant steels

RD 26.260.010-2002: The leading document on standardization. The list of standard documentation on standardization on the cells and devices working under pressure.

RD 26.260.011-99: Methodological instructions. Calculated setting of standards for air-tightness of vessels and apparatuses.

RD 26.260.12-99: Service life extension of liquid carbon dioxide vessels. Instructional guidelines.

RD 26.260.15-2001: The leading document. Positive material identification of the main and welding materials and finished goods.

RD 26.260.16-2002: Expert technical diagnostics of vessels and equipment operating under pressure at gas and gas condensate and oil production and processing facilities in the northern regions of the Russian Federation and underground gas storage facilities

RD 26.260.225-2001: Bodies of cylindrical vessels and devices. Technology, quality assurance

RD 26-01-55-84: Evaporating devices. Norms of calculation for durability.

RD 26-01-87-86: Fin Heat Exchangers. Methods of Strength Analysis and Leak Testing

RD 26-02-77-88: Columnar devices. Installation of plates. Technology, equipment, accessories

RD 26-02-80-2004: The leading document. Welded coils for pipe furnaces. Requirements to design, production and delivery.

RD 26-14-88: Vessels and devices. Tenacity standards and testing. Heat exchange elements.

RD 26-17-049-85: Organization of storage, preparation and control of welding materials

RD 26-17-086-88: Weld joints. Quality control of heat treatment equipment

RD 26-17-78-87: Pulsed-arc welding of chemical oil equipment from stainless steels with a consumable electrode in argon

RD 3689-001-00220302/31-2004: Radiant pipes and components for reaction pipe furnaces. Requirements for design, production and delivery.

RD 95 10541-98: Equipment for working with radioactive media. Classification

RD RTM 0352-76-81: Methods of welding in the manufacture of vessels and apparatus

RDI 26-15-80: Instructions for making inner vessels of isothermal tanks for liquefied carbon dioxide

RTM 26-44-82: Heat treatment of petrochemical equipment and its parts

SO 153-34.17.439-2003: Instruction for prolongation of exploitation term of pressure vessels

TU 26-01-949-85: The devices gummed with the mechanical mixing device of volume 1; 2; 3.2; 6.3; 10 and 16 m3

TU 26-02-1102-89: Shell and tube heat exchangers of increased thermal efficiency with an expander on the housing

TU 26-02-1158-95: Horizontal air coolers

TU 26-02-1162-95: Shell and tube heat exchangers for elevated temperatures and pressures with a floating head and a compensator on it. Technical conditions

TU 26-02-19-75: Steel castings for equipment of oil refineries, petrochemical plants

TU 3681-134-00220302-2007: Air coolers block-modular complete AVG-KB. Technical specifications

TU 4112-091-00220302-2005: Steel castings for equipment of oil refineries and petrochemical plants

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English
Price: $283.00
imgalt
Clear sheet glass. Specifications
Language: English
Price: $250.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!