GOST 14896-84
ГОСТ 14896-84
|
|
Rubber u-packing seals for hydraulic devices
Манжеты уплотнительные резиновые для гидравлических устройств
Status: Effective - Supersedes. The limitation of the effectiveness period has been lifted: Protocol No. 4-93 of the IGU dated 10.21.93 (IUS 4-1994)
The standard applies to rubber cuffs designed to seal the gap between the cylinder and the piston (plunger, rod) in hydraulic devices operating in reciprocating motion with a speed of relative movement of not more than 0.5 m
Стандарт распространяется на резиновые манжеты, предназначенные для уплотнения зазора между цилиндром и поршнем (плунжером, штоком) в гидравлических устройствах, работающих в условиях возвратно-поступательного движения со скоростью относительного перемещения не более 0,5 м/с, при давлении от 0,1 до 50 МПа, температуре от минус 60 до плюс 200 °С, ходе до 10 м и частоте срабатывания до 0,5 Гц.
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
3/27/1984
SKU: RUSS20007
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.10 Testing and monitoring products of rubber and plastics industry »
4.10.1 Rubber products »
ISO classifier »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.50 Seals »
National standards »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.50 Seals »
National Standards for KGS (State Standards Classification) »
Latest edition »
L Chemical products and rubber-asbestos products »
L6 Rubber and asbestos products »
L63 Rubber technical products »
As a Replacement Of:
GOST 14896-74: Rubber seals of reduced cross-section for hydraulic devices
GOST 6969-54: Cuffs (collars) rubber sealing up to 300 mm in diameter for hydraulic devices
The Document References:
GOST 10007-80: Polytetrafluoroethylene. Specifications
GOST 1033-79: Fatty cup grease. Specifications
GOST 10363-78: Oil ЭШ for hydraulic systems of high-load mechanisms. Specifications
GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications
GOST 10589-87: Moulding polyamide 610. Specification
GOST 12433-83: Standard isooctanes. Specifications
GOST 13808-79: Rubber. Method for the determination of low temperature resistance according to elastic rebound after compression
GOST 14192-96: Cargo marking
GOST 14296-78: Grease ВНИИ НП-279. Specifications
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15152-69: Unified system of corrosion and ageing protection. Industrial rubber products for tropics. General requirements
GOST 16295-82: Packing anticorrosive paper. Specifications
GOST 16422-79: Transmission grease ЦИАТИМ-208. Specifications
GOST 16511-86: Wooden boxes for electrical equipment. Specifications
GOST 16728-78: Oil ВНИИ НП-403. Specifications
GOST 17216-2001: Industrial cleanliness. Grades of liquids purity
GOST 17711-93: Cast copper-zink alloys (brass). Grades
GOST 1805-76: Apparatus oil МВП. Specifications
GOST 18573-86: Wooden boxes for the production of chemical industry
GOST 20363-88: Transparent drawing paper. Specifications
GOST 20799-75: Industrial oils. Specifications
GOST 21150-87: Litol-24 grease
GOST 21743-76: Aviation oils
GOST 24811-81: Rubber wipers for rods. Types, basic parameters and dimensions
GOST 25670-83: Basic norms of interchangeability. Limit deviations of dimensions without tolerance indication
GOST 26.008-85: Lettering for inscriptions applied by engraving method. Executive dimensions
GOST 262-93: Rubber, vulcanized. Determination of tear strength (throuser, angle and crescent test pieces)
GOST 269-66: Rubber. General requirements for the physical mechanical tests
GOST 270-75: Rubber. Method of the determination elastic and tensile stress-strain properties
GOST 2712-75: Grease АМС. Specifications
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 426-77: Rubber. Method for the determination of abrasion resistance under slipping
GOST 493-79: Tin-free foundry bronzes. Grades
GOST 8.051-81: State system for ensuring the uniformity measurements. Permissible errors of measurement of linear dimensions to 500 mm
GOST 8.326-89: State system for ensuring the uniformity of measurements. Metrological certification measuring instruments
GOST 892-89: Tracing paper. Specifications
GOST 9.029-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing of resistance to ageing under static deformation of compression
GOST 9.030-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing resistance to attack by corrosive media in limp state
GOST 9569-79: Paraffin paper
GOST 9833-73: Rubber toroidal sealing rings for hydraulic and pneumatic equipment. Construction and dimensions
GOST 9972-74: Petroleum turbine oils with additives
OK 005-93: All-Russia Classification of Products (Part 1)
OK 005-93: All-Russia Product Classification (OKP) (Part 13)
OK 005-93: All-Russia Classification of Products (OKP)
OK 005-93: All-Russia Classification of Products (Part 17)
OK 005-93: All-Russia Product Classification (OKP) (Part 3)
OK 005-93: All-Russia Classification of Products (OKP) (Part 4)
OK 005-93: All-Russia Classification of Products (Part 5)
OK 005-93: All-Russia Classification of Products (Part 6)
OK 005-93: All-Russia Product Classification (OKP) (Part 7)
OK 005-93: All-Russia Classification of Products (OKP) (Part 8)
OK 005-93: All-Russia Classification of Products (part 9)
OK 005-93: All-Russia Classification of Products (OKP) (Part 10)
OK 005-93: All-Russia Classification of Products (Part 11)
OK 005-93: All-Russia Classification of Products (part 12)
OK 005-93: All-Russia Classification of Products (OKP) (Part 14)
OK 005-93: All-Russia Classification of Products (part 15)
OK 005-93: All-Russia Classification of Products (Part 16)
OK 005-93: All-Russia Classification of Products (Part 17)
OK 005-93: All-Russia Classification of Products (Part 18)
OK 005-93: All-Russia Classification of Products (Part 19)
OK 005-93: All-Russia Classification of Products (Part 18)
OK 005-93: All-Russia Classification of Products (Part 21)
OK 005-93: All-Russia Classification of Products (OKP) (Part 22)
OST 38.01412-86: Bobbin oil АУ.
The Document is Referenced By:
GOST 19099-86: Lubricating systems
GOST 19497-90: Chill casting machines
GOST 26616-85: Sets of portable multi-impression press moulds for manufacturing of rubber u-packing seals. Design and dimensions
GOST 26617-85: Sets of three-cassette press-moulds for manufacturing of rubber u-packing seals. Design and dimensions
GOST 26618-85: Sets of two-cassette press-moulds for manufacturing of rubber u-packing seals. Design and dimensions
GOST 26619-85: Single-impression press moulds for manufacturing of rubber u-packing seals. Design and dimensions
RD 102-002-88: Machines, tools and equipment for pipeline construction. Designing and manufacturing.
RD 153-34.0-04.185-2003: Machines and equipment for construction, technical re-equipment and repair of energy facilities. Requirements for design, materials, manufacturing, acceptance and testing
RD 22-207-88: Lifting machines. General requirements and production standards
RD 36-62-00: Hoisting equipment. General technical requirements.
ST TsKBA 057-2008: Pipe fittings. The friction coefficients in the nodes of reinforcement
Customers Who Viewed This Item Also Viewed:
 |
Building materials. Methods for combustibility test
Language: English |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Building materials spread flame test method
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.