RD 153-39.4-075-01
РД 153-39.4-075-01
|
|
Rules of maintenance overhaul of oil-trunk pipeline at waterway, railway and category I-IV highway crossings.
Правила капитального ремонта магистральных нефтепродуктопроводов на переходах через водные преграды, железные и автомобильные дороги I-IV категорий
Status: Not effective - No longer valid. Order of the Ministry of Energy of Russia No. 255 dated March 31, 2016
The guidance document applies to underwater crossings through rivers with a natural and regulated regime and water bodies more than 30 m wide or more than 1.5 m deep, and also to crossings of I and IV categories of railways and highways made of the type “pipe in a protective case” and laid in the following ways: - open method of laying cases at a depth of not more than 4 m (at the intersection of the road of category II and below, or if it is impossible to use the trenchless method); - by the trenchless method made by the following methods: a) horizontal drilling, used for soils of I – IV categories, except flooded and water-saturated sands and sandy loams (when laying covers of large diameter and from 40 to 60 m long); b) a puncture used in soils of categories I - III, as well as in clay soils of category IV, which do not have solid inclusions; c) pushing the casing into the ground with the subsequent manual development of the ground in a pipe laid in any soil except rock. The guidance document does not apply to crossings and structures across reservoirs (seas, estuaries, lakes) more than 10 km wide, estuarine sections of rivers in the tidal current, to pass through small water barriers with depths up to 1.5 m in low water and not wide more than 30 m, the repair of which does not require special equipment and technology.
Руководящий документ распространяется на подводные переходы через реки с естественным и зарегулированным режимом и водоемы шириной более 30 м или глубиной свыше 1,5 м, а также на переходы через железные и автомобильные дороги I - IV категорий, выполненные по типу «труба в защитном футляре» и проложенные следующими способами: - открытым способом прокладки футляров при глубине не более 4 м (при пересечении автодороги II категории и ниже или в случае невозможности применения бестраншейного способа); - бестраншейным способом, выполненным следующими методами: а) горизонтального бурения, применяемого для грунтов I - IV категорий, кроме плывунов и водонасыщенных песков и супесей (при укладке кожухов большого диаметра и длиной от 40 до 60 м); б) прокола, применяемого в грунтах I - III категории, а также в глинистых грунтах IV категории, не имеющих твердых включений; в) продавливания кожуха в грунт с последующей ручной разработкой грунта в трубе, прокладываемой в любых грунтах за исключением скальных. Руководящий документ не распространяется на переходы и сооружения через водоемы (моря, лиманы, озера) шириной более 10 км, устьевые участки рек в зоне приливно-отливного течения, на переходы через малые водные преграды с глубинами до 1,5 м в межень и шириной не более 30 м, ремонт которых не требует специальной техники и технологии.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Ministry of Energy of Russia,
6/6/2001
SKU: RUSS20063
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Sectoral and departmental regulatory and methodological documents »
Design and construction of oil and gas industry facilities »
Welding regulations »
Welding work »
Welding regulations »
Pipelines »
Welding regulations »
Welding materials »
Welding regulations »
Documentation »
Welding regulations »
Defects »
Welding regulations »
Welding work »
Automatic welding »
Welding regulations »
Welding work »
Surfacing »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Welding materials »
Electrodes »
Welding regulations »
Welding materials »
Gases »
Technical Supervision »
Section I. Technological, construction, energy supervision and environmental protection regarding limitation of negative anthropogenic impact »
IV. Regulatory legal acts and regulations »
2. Industrial safety »
2.5. Objects of main pipeline transport »
PromExpert »
SECTION IV. INDUSTRIAL SAFETY »
II Industrial safety requirements for operation of a hazardous production facility »
2 Special industrial safety requirements for operation of a hazardous production facility »
2.8 Industrial safety requirements for transport of hazardous substances »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
2003.200.13 Pipelines and their components »
The Document References:
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.4.004-74: Filtering protective mask RPG-67
GOST 17.1.1.02-77: Nature protection. Hydrosphere. Classification of water bodies
GOST 17.1.3.10-83: Nature protection. Hydrosphere. General requirements for surface and underground water control against pollution by oil and oil products while supplying by pipe-line
GOST 17.4.3.02-85: Nature protection. Soils. Requirement for fertile layer conservation in performing earth-moving
GOST 17.5.1.01-83: Nature protection. Land reclamation. Terms and definitions
GOST 17.5.3.06-85: Nature protection. Lands. Requirements for determination of the fertile soil layer standard disposal while performing earth-moving
GOST 17269-71: Gas- and dust-protecting filtering respirators Ru-60m and Ru-60mu
GOST 18322-78: Equipment maintenance and repair system. Terms and definitions
GOST 19179-73: Hydrology of land. Terms and definitions
GOST 2246-70: Welding steel wire. Specifications
GOST 25812-83: Steel pipe mains. General requirements for corrosion protection
GOST 27.002-89: Industrial product dependability. General principles. Terms and definitions
GOST 310.5-88: Cements. Test method for heat of hydration
GOST 3282-74: General-purpose low-carbon steel wire. Specifications
GOST 8267-93: Crushed stone and gravel of solid rocks for construction works. Specifications
GOST 8735-88: Sand for construction work. Testing methods
GOST 8736-93: Sand for construction works. Specifications
GOST 9.602-89: Constructions, underground. General requirements for corrosion protection
GOST 9087-81: Welding melted fluxes
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST 9467-75: Metal covered electrodes for manual arc welding of structural and heat-resistant steels. Types
PB 03-108-96: Process pipeline design and safe operation rules
PPB 01-93*: Fire Safety Rules in the Russian Federation
RD 102-011-89: Occupational Safety and Health. Management and Procedural Documents
RD 153-39.4-041-99: Operating rules and regulations for trunk oil product pipelines.
RD 31.84.01-90: Uniform occupational safety rules for diving operations
RD 39-30-467-80: Quality Control Guidelines to Insulation Coverings for In-Service Pipelines Under Repair
SanPiN 4630-88: Sanitary rules and standards for preservation of surface waters against pollution
SN 452-73: Standards for the Allocation of Land for Trunk Pipelines
SNiP 11-01-95: Instructions on the procedure of elaboration, coordination, approval, and composition of design documentation for construction of enterprises, buildings, and structures
SNiP 11-02-96: Engineering surveying for construction. fundamentals
SNiP 2.01.14-83: Determination of design hydrologic characteristics
SNiP 2.03.11-85: Corrosion protection of buildings structures
SNiP 2.06.01-86: Hydraulic facilities. basic provisions of design activities
SNiP 3.01.03-84: Survey operations in construction
SNiP 3.02.01-87: Earthen structures, foundation and basis
SNiP 4.02-91: Books of estimating standards and rates for construction works
VPPB 01-03-96: Fire code for JSC Transnefteproduct
VSN 004-88: Construction of trunk pipelines. Technology and management.
VSN 006-89: Construction Of Main And Field Pipelines Welding
VSN 008-88: Construction of trunk and field pipelines. Anticorrosion and heat insulation
VSN 010-88: Construction of main pipelines. Underwater transitions
VSN 011-88: Main pipeline and flowline construction. Bore cleaning and testing
VSN 012-88: Main pipeline and flowline construction. Quality control and commissioning of works
VSN 014-89: Construction of Trunk and Field Pipelines. Environmental Protection
VSN 163-83: Design Considerations for the Deformation of River Beds and Shorelines of Water Bodies at Underwater Petroleum and Natural Gas Trunk Pipeline Crossings
|
Customers Who Viewed This Item Also Viewed:
 |
Industrial process measurement and control equipment. Reliability. General requirements and test methods
Language: English |
Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
Language: English |
System for ensuring the reliability and safety of construction sites. Loads and impacts. design standards
Language: English |
Heating, ventilation and air conditioning. Fire Safety Requirements
Language: English |
Reliability of atomic power stations and their equipment. General statements and reliability index nomenclature
Language: English |
Electromagnetic compatibility of technical equipment. Technical equipment for nuclear power plants. Requirement and test methods
Language: English |
Billets made of corrosion-resistant steels of 12Х18Н9Т, 12Х18Н10Т, 08Х18Н10Т, 10Х17Н13М2Т, 12Х18Н12Т and 03Х21Н32М3Б types.
Language: English |
Dependability in technics. Terms and definitions
Language: English |
System of products development and launching into manufacture. Technical assignment. Requirements to contents and form of presentation
Language: English |
Reliability in technology. Composition and general rules for setting reliability requirements
Language: English |
Rails of types P38 and P42. Technical conditions
Language: English |
Stainless corrosion resisting, heat-resisting and creep resisting steel and alloy on iron-nickel-based products. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
