SP 34-116-97

СП 34-116-97

Instructions For Design, Construction and Redesign of Field Oil and Gas Pipelines

Ведомственные строительные нормы Инструкция по проектированию, строительству и реконструкции промысловых нефтегазопроводов

Status: Not effective - Canceled. Order of the Ministry of Energy dated July 26, 2017 No. 673

The standards apply to the projected under construction and reconstructed field steel pipelines with a diameter of up to 1,400 mm inclusively with an overpressure of the medium not exceeding 32.0 MPa of oil, gas, gas condensate fields and underground gas storage facilities. The instruction establishes the technical characteristics of field oil and gas pipelines ensuring the safety of people, structures and the environment in the areas of laying of these pipelines when they perform the main task of transporting the planned amount of product. Achieving the required operational characteristics is carried out by regulating design solutions, assigning a system of design coefficients to ensure the required level of reliability, assigning safe distances between parallel pipelines and from pipelines to ground engineering structures providing a standardized level of risk, assigning requirements to technological operations for constructing pipelines that ensure high quality construction of pipelines in various natural loviyah with minimal impact on the environment and for safety, by the application of advanced technology solutions.

Нормы распространяются на проектируемые строящиеся и реконструируемые промысловые стальные трубопроводы диаметром до 1400 мм включительно с избыточным давлением среды не выше 32,0 МПа нефтяных, газовых, газоконденсатных месторождений и подземных хранилищ газа. Инструкция устанавливает технические характеристики промысловых нефтегазопроводов, обеспечивающие безопасность людей, сооружений и окружающей среды в зонах прокладки этих трубопроводов при выполнении ими основной задачи по транспорту планового количества продукта. Достижение необходимых эксплуатационных характеристик осуществляется путем регламентации конструктивных решений, назначения системы расчетных коэффициентов, обеспечивающих необходимый уровень надежности, назначения безопасных расстояний между параллельными трубопроводами и от трубопроводов до наземных инженерных сооружений, обеспечивающих нормативный уровень риска, назначения требований к технологическим операциям сооружения трубопроводов, обеспечивающих высокое качество строительства трубопроводов в различных природных условиях при минимальном воздействии на окружающую среду и соблюдении техники безопасности, путем применения прогрессивных технологических решений.

Choose Language: 
Format: Electronic (pdf/doc)
Page Count: 134

Approved: Ministry of Fuel and Energy of the Russian Federation, 12/23/1997

SKU: RUSS20067

Price: $610.00

The Product is Contained in the Following Classifiers:

Construction (Max) » Regulations » Sectoral and departmental regulatory and methodological documents » Design and construction of oil and gas industry facilities »

Welding regulations » Welding work »

Welding regulations » Main materials »

Welding regulations » Pipelines »

Welding regulations » Metal structures »

Welding regulations » Welding materials »

Welding regulations » Welding staff »

Welding regulations » Certification »

Welding regulations » Documentation »

Welding regulations » Non-destructive control »

Welding regulations » Mechanical Testing »

Welding regulations » Heat treatment »

Welding regulations » Defects »

Welding regulations » Assembly devices »

Welding regulations » Welding work » Automatic welding »

Welding regulations » Welding work » Surfacing »

Welding regulations » Welding work » Dusting »

Welding regulations » Main materials » Steel, cast iron »

Welding regulations » Main materials » Polymers »

Welding regulations » Welding materials » Electrodes »

Welding regulations » Welding materials » Wire »

Welding regulations » Welding materials » Fluxes »

Welding regulations » Welding materials » Gases »

ISO classifier » 75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION » 75.200 Equipment for oil refining, oil products and natural gas » 2003.200.13 Pipelines and their components »

The Document References:

GOST 10157-79: Gaseous and liquid argon. Specifications

GOST 11262-80: Plastics. Tensile strength test method.

GOST 12821-80: Steel butt-welded flanges for Pnom from 0,1 to 20,0 MPa (from 1 to 200 kgf/cm2). Design and dimensions

GOST 13073-77: Zinc wire

GOST 13518-68: Plastics. Method for determination of environmental stress-cracking resistance of polyethylene

GOST 14236-81: Polymer films. Tensile strength test method

GOST 14759-69: Adhesives. Method of determination of shear strength

GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods

GOST 15140-78: Paintwork materials. Methods for determination of adhesion

GOST 16337-77: High-pressure polyethylene. Specifications

GOST 16783-71: Plastics. Method of determining the brittleness temperature at squeezing the specimen folded up as a loop

GOST Nature protection. Soils. Requirement for fertile layer conservation in performing earth-moving

GOST Nature protection. Land reclamation. General requirements for lands to be backfilled

GOST Nature protection. Lands. Requirements for determination of the fertile soil layer standard disposal while performing earth-moving

GOST 18299-72: Paintwork materials. Method for determination of tensile strength, relative elongation at tear and modulus of elasticity

GOST 2246-70: Welding steel wire. Specifications

GOST 24950-81: Bent branches and curved inserts for the turns of the linear parts of steel long distance pipe lines

GOST 25100-95: Soils. Classification

GOST 25225-82: Non-destructive testing. Welded joints of tubing. Magnetographic method

GOST 25812-83: Steel pipe mains. General requirements for corrosion protection

GOST 25815-83: Propellers. Terms and definitions

GOST 25820-83: Lightweight concrete. Specifications

GOST 2678-94: Rolled roofing and waterproof materials. Methods of testing

GOST 30416-96: Soils. Laboratory testing. General requirements

GOST 411-77: Rubber and glue. Methods for determination of metal bond strength at separation

GOST 4640-93: Mineral wool. Specifications

GOST 4650-80: Plastics. Methods for the determination of water absorption

GOST 5583-78: Industrial and medical gaseous oxygen

GOST 618-73: Aluminum foil for technical purposes. Specifications

GOST 6996-66: Welded joints. Methods of mechanical properties determination

GOST 7512-82: Nondestructive testing. Welded joints. Radiography method

GOST 7871-75: Aluminum and aluminium alloy welding wire

GOST 8050-85: Carbon dioxide,

GOST 8273-75: Packing paper

GOST 9.010-80: Unified system of corrosion and ageing protection. Compressed air for atomization of paint materials. Technical requirements and methods of control

GOST 9.402-80: Metal surface preparation for painting

GOST 9.602-89: Constructions, underground. General requirements for corrosion protection

GOST 9087-81: Welding melted fluxes

GOST 9238-83: Construction and rolling stock clearance diagrams for the USSR railways of 1520 (1524) mm gauge.

GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature

GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications

GOST 9467-75: Metal covered electrodes for manual arc welding of structural and heat-resistant steels. Types

GOST 9544-93: Pipeline cut-off valves

OST 102-51-85: Non-destructive testing. Welded pipe joints. Radiographic method.

RD 39-132-94: Regulations for Operation, Inspection, Repair and Rejection of the Field Pipelines 1994

SN 452-73: Standards for the Allocation of Land for Trunk Pipelines

SNiP 1.02.07-87: Engineering Research for Construction

SNiP 1.06.05-85: Regulation on construction design supervision of enterprises, buildings and installation by design organizations

SNiP 11-01-95: Instructions on the procedure of elaboration, coordination, approval, and composition of design documentation for construction of enterprises, buildings, and structures

SNiP 2.01.01-82: Construction climatology and geophysics

SNiP 2.02.03-85: Pile foundations

SNiP 2.02.04-88: Bases and foundations on the permafrost soils

SNiP 2.03.11-85: Corrosion protection of buildings structures

SNiP 3.01.04-87: Project acceptance for operation after construction

SNiP 3.02.01-87: Earthen structures, foundation and basis

SNiP 3.04.03-85: Protection of construction structures and facilities from corrosion

SNiP 3.05.03-85: Heat networks

SNiP 32-03-96: Aerodromes

SP 11-101-95: Procedure of Development, Coordination, Approval and Composition of Feasibility Studies for Construction of Enterprises, Buildings and Structures

TU 36-1180-85: Industrial Structures for Thermal Insulation of Pipelines, Apparatus and Tanks

VNTP 3-85: Norms of process design of facilities for gathering transport and treatment of oil gas and water of oil fields

VSN 004-88: Construction of trunk pipelines. Technology and management.

VSN 005-88: Construction of field steel pipelines Technology and arrangement

VSN 006-89: Construction Of Main And Field Pipelines Welding

VSN 007-88: Construction of Trunk and Field Pipelines. Design and Ballasting

VSN 008-88: Construction of trunk and field pipelines. Anticorrosion and heat insulation

VSN 009-88: Construction of main and commercial pipelines. Means and installations of cathodic protection.

VSN 011-88: Main pipeline and flowline construction. Bore cleaning and testing

VSN 012-88: Main pipeline and flowline construction. Quality control and commissioning of works

VSN 014-89: Construction of Trunk and Field Pipelines. Environmental Protection

VSN 51-3-85: Design of field steel pipelines

The Document is Referenced By:

GOST R 55990-2014: Oil and gas-oil fields. Field pipelines. Design codes

GOST R 57430-2017: Pipes, fitting from ductile iron with spherical graphite and their connections for trade oil pipelines. Specifications

GOST R 57955-2017: Buildings and facilities for oil and gas producing industries. Design standards

OST 153-39.4-010-2002: Method of determination of residual life of oil and gas pipelines and headwork pipelines.

Resolution 536: Requirements for documentation of industrial safety management systems

SP 366.1325800.2017: Field pipelines. Grade of design based on the risk analysis

TU 1469-006-00153229-2001: Parts connecting on Рр up to 16 MPa (160 kgf

Customers Who Viewed This Item Also Viewed:

Special railway rolling stok. Dynamic and strength testing procedures
Language: English
Price: $198.00
Blanks for marine shafts and rudder stocks. Specifications
Language: English
Price: $216.00


RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!