GOST 28013-98
ГОСТ 28013-98
|
|
Mortars. General specifications
Растворы строительные. Общие технические условия
Status: Effective - Supersedes. IUS 5-1999
The standard applies to building mortars on mineral binders used for masonry and installation of building structures during the construction of buildings and structures, fixing cladding products, plaster. The standard does not apply to special solutions (heat-resistant, chemically resistant, fire-resistant, heat and waterproofing, grouting, decorative, stress, etc.).
Стандарт распространяется на строительные растворы на минеральных вяжущих, применяемые для каменной кладки и монтажа строительных конструкций при возведении зданий и сооружений, крепления облицовочных изделий, штукатурки. Стандарт не распространяется на специальные растворы (жаростойкие, химически стойкие, огнестойкие, тепло- и гидроизоляционные, тампонажные, декоративные, напрягающие и др.).
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstroy of Russia,
12/29/1998
SKU: RUSS20345
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Documents System of normative documents in construction »
6. Regulatory documents for building materials and products »
k.62 Concretes and mortars »
ISO classifier »
91 CONSTRUCTION MATERIALS AND CONSTRUCTION »
91.100 Building Materials »
91.100.10 Cement. Gypsum. Lime. Building mixture »
National standards »
91 CONSTRUCTION MATERIALS AND CONSTRUCTION »
91.100 Building Materials »
91.100.10 Cement. Gypsum. Lime. Building mixture »
National Standards for KGS (State Standards Classification) »
Latest edition »
Zh Construction and building materials »
Zh1 Construction materials »
Zh13 Concretes and mortars »
National Standards for OKSTU »
REINFORCED CONCRETE STRUCTURES AND PARTS (INCLUDING REINFORCED CONCRETE CONCRETE PRODUCTS) »
Concrete and mortars »
As a Replacement Of:
GOST 28013-89: Mortars. General specifications
The Document References:
GOST 10178-85: Portland cement and portland blastfurnace slag cement. Specifications
GOST 10181-2014: Concrete mixtures. Methods of testing
GOST 10354-82: Polyethylene film Specifications
GOST 125-79: Gypsum binders. Specifications
GOST 18481-81: Glass hydrometers and cylinders. General specifications
GOST 21216.12-93: Clay raw materials. Method for determination of fraction retained on sieve N 0063
GOST 21216.2-93: Clay raw materials. Method for determination of finely dispersed fractions
GOST 21216-2014: Clay raw materials. Test methods
GOST 2226-2013: Bags made of paper and composite materials. General specifications
GOST 22266-2013: Sulphate-resistant cements. Specifications
GOST 23732-2011: Water for concretes and cement mortars Technical specifications.
GOST 24211-2008: Admixtures for concretes and mortars. General specifications
GOST 25328-82: Masonry cement. Specifications.
GOST 25592-91: Mixes of fly-ash and slag of thermal plants for concretes. Specifications
GOST 25818-2017: Fly ash thermal power plants for concrete. Technical conditions
GOST 25820-2000: Lightweight aggregates concretes. Specifications
GOST 2642.11-97: Refractories and refractory raw materials. Method for determination of potassium and sodium oxides
GOST 2642.5-2016: Refractories and refractory raw materials. Methods for the determination of iron (III) oxide
GOST 26633-2015: Heavy-weight and sand concretes. Specifications
GOST 26644-85: Slag crushed stone and slag sand fly-ash for concrete. Specifications
GOST 28013-89: Mortars. General specifications
GOST 30108-94: Building materials and elements. Determination of specific activity of natural radioactive nuclei
GOST 30459-2008: Admixtures for concretes and mortars. Determination and estimate of the efficiency
GOST 3594.4-77: Moulding clay. Methods for the determination of sulphur content
GOST 4.233-86: Product-quality index system. Building. Mortars. Index nomenclature
GOST 5578-94: Slag crushed stone and slag sand of ferrous and non-ferrous metallurgy for concretes. Specifications
GOST 5802-86: Mortars. Test methods.
GOST 8735-88: Sand for construction work. Testing methods
GOST 8736-2014: Sand for construction works. Specifications
GOST 9179-77: Lime for building purposes. Specifications
SNiP II-3-79: Heat Engineering for the Construction Industry
The Document is Referenced By:
GOST 11024-2012: Concrete and reinforced concrete panels for external walls of residential and civil buildings. General specifications
GOST 13578-2019: Lightweight concrete panels on porous aggregates for the exterior walls of industrial buildings. General specifications
GOST 25592-2019: Ashes and slag mixtures of thermal power plants for concrete. Technical conditions
GOST 25592-91: Mixes of fly-ash and slag of thermal plants for concretes. Specifications
GOST 25818-2017: Fly ash thermal power plants for concrete. Technical conditions
GOST 30459-2003: Additives for concretes and mortars. Methods of determining the efficiency
GOST 30459-2008: Admixtures for concretes and mortars. Determination and estimate of the efficiency
GOST 31310-2005: Wall three-layer reinforced concrete panels with energy-efficient insulation. General specifications
GOST 31310-2015: Wall three-layer reinforced concrete panels with energy-efficient insulation. General specifications
GOST 31358-2007: Dry building flooring cement binder mixes. Specifications
GOST 31424-2010: Non-metallic construction materials from sifting of crusting solid stone in aggregate manufacturing. Specifications
GOST 32047-2012: Masonry. Method of compressive test
GOST 32488-2013: Exterior wall panels of claydite-concrete for residential and public buildings. Specificatiоns
GOST 33699-2015: Dry building putty cement binder mixes. Specifications
GOST 33929-2016: Concrete with polysterene aggregates. Specifications
GOST 34518-2019: Industrial furnaces and thermal units. Rules for the organization and production of work, monitoring of performance and requirements for the results of work
GOST 34519-2019: Industrial chimney and ventilation pipes. Rules for the organization and production of work, monitoring of performance and requirements for the results of work
GOST R 54923-2012: Polymer composite wall ties for multilayer envelope buildings. Specifications
GOST R 56587-2015: Concrete mixtures. Method for determination of time of setting
GOST R 56592-2015: Mineral Admixtures for Concretes and mortars. General specifications
GOST R 58894-2020: Condensed silica fume for concrete and mortars. Specifications
GOST R 58937-2020: A decorative and protective finishing layer made of piece materials for facade thermal insulation composite systems with external plaster layers. Specifications
GOST R 58949-2020: Building concretes and mortars. Methods for determination, rules for control and assessment of moisture in structures
GOST R 70307-2022: Fine-grained concretes and mortars for construction. Methods for determination of strength in thin-walled and thin-walled structures
MDS 12-23.2006: Temporary recommendations on the technology and organization of construction of multifunctional high-rise buildings and building complexes in Moscow
MDS 12-24.2006: Installation of ordinary, decorative and waterproofing plaster coatings of building facades
ODM 218.2.078-2016: Guidelines for the selection of the structure for strengthening the slopes of the road bed of public roads
OSN-APK 2.10.32.001-04: Instructions for the use of chemical additives in concrete and mortars for rural construction
Resolution 2425: On approval of the single list of products subject to mandatory certification and the single list of products subject to declaration of conformity, amending the decree of the Government of the Russian Federation of December 31, 2020 N 2467 and repealing certain acts of the Government of the Russian Federation
RMD 23-16-2012 Sankt-Peterburg: Recommendations for energy efficiency in residential and public buildings
RMD 51-25-2018 St. Petersburg: Recommendations for the design, installation and operation of facade systems for new construction, reconstruction and repair of residential and public buildings in St. Petersburg. Part II Recommendations for the operation and repair of facade systems for new construction and reconstruction of residential and public buildings in St. Petersburg
RMD 52-01-2006 Sankt-Peterburg: Design and construction of enclosing structures of residential and public buildings using cellular concrete in St. Petersburg. Part I
SP 15.13330.2012: Masonry and reinforced masonry structures
SP 17.13330.2017: The roofs
SP 23-101-2000: Design of thermal performance of buildings
SP 23-101-2004: Design of thermal protection of buildings
SP 327.1325800.2017: Exterior masonry walls with brick veneer. Rules of design, operation and repair
SP 335.1325800.2017: Large-panel construction system. Design rules
SP 434.1325800.2018: Polystyrene concrete enclosures. Design rules
SP 472.1325800.2019: Armor-based systems of bridges and retaining walls on highways. Design rules
SP 70.13330.2012: Bearing and enclosing structures. Updated living edition of SNiP 3.03.01-87
SP 71.13330.2017: Insulation and finish coatings
SP 82-101-98: Preparation and use of masonry mortars. To replace SN 290-74. Letter № AB-20-218 / 12 dated 06.17.98.
SP 83.13330.2016: Industrial furnaces and brick chimneys
STO DOKTOR BETON 68686983-001-2011: Dry building mixtures trade mark "ДОКТОР БЕТОН®" for waterproofing and repair concrete construction. Classification. Nomenclature of indicators. Technical requirements
STO DOKTOR BETON 68686983-002-2011: Dry building mixtures trade mark "ДОКТОР БЕТОН®" for waterproofing and repair concrete construction. Technical specifications and quality characteristics
STO DOKTOR BETON 68686983-003-2011: Dry building mixtures trade mark "ДОКТОР БЕТОН®" for waterproofing and repair concrete construction. Technologies execution and methods estimation of quality
TR 120-01: Technical recommendations on the waterproofing of the underground part of buildings and structures using materials "Akvatron-6u", "Akvatron-8b", "Akvatron-12"
TR 122-01: Technical recommendations on plastering technology inside buildings
TR 137-03: Technical recommendations on the use of dry specialized finishing mixtures for exterior and interior work in the construction of new buildings and structures, reconstruction and repair
TR 140-03: Technical recommendations on the technology of painting the interiors and facades of residential and public buildings under construction
TR 149/1-05: Technical recommendations on the technology of the use of a complex of finishing materials in the reconstruction and overhaul of the internal surfaces of buildings
TR 149-03: Technical recommendations on the technology of using the complex of specialized finishing materials for the renovation of external and internal surfaces during reconstruction and major repairs of buildings
TR 166-04: Technical recommendations for quality assurance of concrete and mortar mixes and prevention of concrete corrosion in reinforced concrete structures
TR 94.11-05: Technological regulation of the operational quality control of construction, installation and special works during the construction of buildings and structures. 11. Painting and wallpaper production
TU 5831-001-54735376-2004: Specifications. Three-layer reinforced concrete panels with flexible fiberglass connections for exterior walls of Styrod system buildings
Customers Who Viewed This Item Also Viewed:
|
Controllers acting without
Language: English |
Building materials. Methods for combustibility test
Language: English |
Building materials spread flame test method
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Clear sheet glass. Specifications
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
|
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.