imgalt

GOST 11828-86

ГОСТ 11828-86

Rotating electrical machines. General test methods

Машины электрические вращающиеся. Общие методы испытаний

Status: Effective

The standard applies to rotating electric machines of direct and alternating current without limiting power, voltage, frequency and establishes test methods common to electric machines of all kinds; Special requirements for testing electric machines of certain types should be established by standards for test methods for electric machines of these types, as well as specifications for specific types of electric machines. The standard does not apply to electrical machines intended for use in onboard systems of mobile means of land-based waterborne and air transport, and to electrical machines that are subject to special requirements, approved in the prescribed manner. The standard is suitable for certification testing.

Стандарт распространяется на вращающиеся электрические машины постоянного и переменного тока без ограничения мощности, напряжения, частоты и устанавливает методы испытаний, общие для электрических машин всех видов; специальные требования по испытаниям электрических машин отдельных видов должны устанавливаться стандартами на методы испытаний электрических машин этих видов, а также техническими условиями на конкретные виды электрических машин. Стандарт не распространяется на электрические машины, предназначенные для применения в бортовых системах подвижных средств наземного водного и воздушного транспорта, и на электрические машины, на которые установлены специальные требования, утвержденные в установленном порядке. Стандарт пригоден для целей сертификационных испытаний.

Choose Language: 
Format: Electronic (pdf/doc)

Approved: USSR State Committee for Standards, 8/15/1986

SKU: RUSS20894

Price: $976.00



imgalt

The Product is Contained in the Following Classifiers:

Evidence base (TR CU, Technical Regulation of the Customs Union) » 001/2011 TR TS. On safety of railway rolling stock » Regulations and standards (to TR CU 001/2011) »

Evidence base (TR CU, Technical Regulation of the Customs Union) » 003/2011 TR TS. On safety of railway infrastructure » Regulations and standards (for TR CU 003/2011) »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.15 Testing and control of products of electronic, optical and electrical industry » 4.15.1 Electric machines, electrical equipment and materials »

ISO classifier » 29 ELECTRICAL ENGINEERING » 29.160 Electric rotating machines » 29.160.01 Machines rotating in general »

National standards » 29 ELECTRICAL ENGINEERING » 29.160 Electric rotating machines » 29.160.01 Machines rotating in general »

National Standards for KGS (State Standards Classification) » Latest edition » E Power and electrical equipment » E6 Electric machines, transformers and converters » E69 Test methods. Packaging. Marking »

National Standards for OKSTU » ELECTRIC MACHINES »

National Standards for OKSTU » ELECTRIC MACHINES » Control methods (testing, analysis, measurements) »


As a Replacement Of:

GOST 11828-75: Rotating electrical machines. General test methods

GOST 25000-81: Electric rotary machines. Heating test methods

The Document References:

PR 50.2.006-94: Procedure for calibration of measurement equipment

PR 50.2.009-94: The testing and approval procedure for the measurement instrumentation

The Document is Referenced By:

FTS ZhT TsL 01-98: Railway passenger cars. Certification requirements

GOST 10159-79: Rotating electrical commutator machines. Test methods

GOST 10169-77: 3-phase synchronous machines. Test methods

GOST 12049-75: D. C. Motors for floor railless electrified transport trucks. General specifications

GOST 12259-75: Electric machines. Methods of determination of cooling gas volume

GOST 13821-77: Single-operator rectifiers with falling external characteristics for arc welding. General specifications

GOST 13822-82: Generating sets and moving diesel-power stations. General specifications

GOST 14177-88: Spindles with built-in drive

GOST 14191-88: Low power rotating electrical machines. Motors for sound recording equipment and electrical players of domestic purpose

GOST 14933-83: Air-suction units for household vacuum cleaners

GOST 14965-80: Three-phase synchronous generators of power over 100 kw

GOST 15880-83: Electric drills

GOST 15880-96: Electric drills. General specifications

GOST 16264.0-2018: Electric machines of low power. Engines General specifications

GOST 16264.0-85: Low-power electric motors

GOST 16312-97: Electric motor frequency convertors with rated power up to 200 kW and frequency to 20000 Hz. Test methods

GOST 17493-80: Electric machine frequency converters with power rating 250 kw up

GOST 18058-80: Three-phase asynchronous squirrel-cage submersible electric motors series ПЭД. Specifications

GOST 18200-90: Above 200 kW rotating electric machines. Synchronous engines. General specifications

GOST 21558-2000: Excitation system for turbo generators, hydrogenerators and synchronous condensers. General specifications

GOST 21558-2018: Excitation systems for turbogenerators, hydrogenerators and synchronous compensators. General specifications

GOST 21558-88: Excitation systems for turbo generators, hydro generators and synchronous condensers

GOST 21671-82: Petrol electric units

GOST 22502-89: Condensing units with hermetic refrigeration compressors for commercial refrigeration machinery

GOST 22782.7-81: Explosion-proof electric equipment with "e" type protection

GOST 23833-95: Commercial refrigeration equipment

GOST 24282-86: Flexible-way electric powered vehicles. Testing methods

GOST 24282-97: Floor-mounted flexible electrified vehicles. Testing methods

GOST 2582-2013: Rotating electrical traction machines for rail and road vehicles. General technical specifications.

GOST 2582-81: Electric rotatory traction machines

GOST 25862-83: Constant speed electrical actuators for remote control. Acceptance rules and methods of tests

GOST 25941-83: Rotating electrical machines. Methods for determining losses and efficiency

GOST 28327-89: Rotating electrical machines. Starting performances of single-speed three-phase cage induction motors for voltages to 660 V inclusive

GOST 28330-89: Asynchronous electrical machines with power from 1 to 400 kw inclusive. Motors

GOST 30195-94: Submersible asynchronous electric motors

GOST 30223-95: Motorised conveyor drums. General specifications

GOST 304-82: Welding generators.

GOST 30630.3.2-2013: Methods for determining the resistance of polymeric insulating materials and systems through the accelerated tests in aggressive gaseous media. General requirements. Testing materials and insulation systems for low-voltage electrical products

GOST 31591-2012: Gearmotors of general purposes. General specifications

GOST 31606-2012: Rotating electrical machines. Asynchronous motors of power from 0,12 to 400 kW inclusive. General technical requirements

GOST 33115-2014: Electric generating plants with diesel and gas internal combustion engines. General specification

GOST 33116-2014: Generating sets driven by gasoline internal combustion engines. General specifications

GOST 34673.2-2020: Railway traction rolling stock. Part 2. Test methods for protection in emergency processes and for measuring the heating of electrical equipment

GOST 3940-2004: Automotive engineering electrical equipment. General specifications.

GOST 3940-84: Electrical equipment for vehicles and tractors. General technical requirements

GOST 533-2000: Rotating electrical machinery. Turbo-generators. General specifications

GOST 5616-89: Water-wheel electrical generators and motor-generators

GOST 6134-2007: Rotodynamic pumps. Test methods

GOST 6625-85: Mine local ventilating fans

GOST 7192-89: Constant-speed electrical actuating mechanisms, ssi

GOST 95-77: Single-operator single-phase transformers for manual arc welding. General specifications

GOST 9630-2018: Three-phase asynchronous motors with voltages above 1000 V. General specifications

GOST 9630-80: Three-phase asynchronous motors. General specifications.

GOST R 50034-92: Electromagnetic compatibility. Asynchronous motors of voltage about 1000 V. Limits and test methods on immunity to electromagnetic disturbance

GOST R 50735-95: Alternating-current generators from 2 to 30 kW for power take-off from motors of moving means. General specifications

GOST R 50968-96: Gearmotors of general purpose. General standard specifications

GOST R 51137-98: Asynchronous controlled variable electric drives for energetic objects. General specifications

GOST R 51689-2000: Rotating electrical machines. Asynchronous motors of power from 0,12 to 400 kW inclusive. General technical reguirements

GOST R 51757-2001: 3-phase induction motors of voltage over 1000 V for auxiliaries of thermal power stations. General specifications

GOST R 52230-2004: Electrical equipment for vehicles and tractors. General specifications

GOST R 52776-2007: Rotating electrical machines. Rating and performance

GOST R 53167-2008: Methods for determination of endurance of polymer electrical insulation materials and systems by means of acceleration tests in chemically active media. General requirements. Materials and insulation systems for low-voltage electrical products tests

GOST R 53174-2008: Electric generating plants with diesel and gas internal combustion engines. General specifications

GOST R 53175-2008: Electric generating plants with gasoline internal combustion engines. General specifications

GOST R 53471-2009: Synchronous three-phase generators of power above 100 kW. General specifications

GOST R 53472-2009: Rotating electrical machines. Asynchronous motors. Test methods

GOST R 54418.2-2014: Renewable power engineering. Wind power engineering. Wind turbines. Part 2. Design requirements for small wind turbines

GOST R 54466-2011: Rotating electrical machines. Asynchronous explosion-proof motors of power from 0,25 to 400 kW inclusive. General technical requirements and test methods

GOST R 55006-2012: Stationary diesel and gas fuelled power plants with internal combustion engines. General specifications

GOST R 55260.1.7-2013: Hydro power plants. Part 1-7. Hydroelectric power station. The general requirements for repair and reconstruction of constructions and equipment

GOST R 55260.2.1-2012: Hydro power plants. Part 2-1. Hydrotreaters. Procurement specification

GOST R 55260.2.1-2022: Hydroelectric power plants. Hydrogenerators. Technical requirements for delivery

GOST R 55260.2.2-2013: Hydro power plants. Part 2-2. Hydrotreaters. Hydraulic estimation procedures of operating conditions

GOST R 56830-2015: Petroleum and natural gas industries. Electrical submersible pump units. General technical requirements

GOST R 57736-2017: Mining equpment. Mine auxiliary fans. General specifications

GOST R 58341.2-2019: Diesel generator sets of nuclear power plants. Accounting for actually depleted resource and estimation of residual resource

GOST R 58341.8-2021: Electric motors of the nuclear power plant unit. Accounting of actually worked out and estimation of residual resource

GOST R 58787-2019: Electric generating sets with internal combustion engines for nuclear power plants. General technical conditions. Accommodation

GOST R 59410-2021: Complex of electrical equipment and drives for control and protection systems of nuclear power plants. Accounting for the actually worked out and assessment of the residual resource

NB ZhT TsP 035-99: Special railway rolling stock. Safety standards

NB ZhT TsT 01-98: Diesel train Safety Standards Change №1

NB ZhT TsT 02-98: Diesel locomotives. Safety regulations

NB ZhT TsT 03-98: Electric trains. Safety Standards. Amendments №1-4

NB ZhT TsT 04-98: Electric locomotives. Safety standards

NB ZhT TsT 07-99: Diesel locomotives, gas turbine locomotives, diesel trains and railcars (rail buses). Electrical equipment traction. Safety standards

OST 24.040.02-78: Locomotive and track machine electric chains. Insulation resistance acceptable values.

PNST 165-2016: Electric generating sets for nuclear plants with internal combustion engines. General specifications. Рlacement requirements

RD 153-39TN-009-96: Ordinance on the System for Maintenance and Repair of Electrical Installations of Trunk Petroleum Pipelines Part I

RD 16.407-2000: Explosionproof electrical apparatus. Repair

RD 34.45.501-88: Model Guidelines for Operation of Generators at Electric Power Generating Stations

RD 34.45.507: Model Guidelines for Operation of Large Electric Motors with Water Cooling of Rotor for Feed Pump Drives

RD EO 1.1.2.01.0713-2013: Provisions on acceptance and testing form conformity assessment for nuclear plants.

ST RK 1518-2006: Diesel locomotives. DC electric rotating traction machines. Requirements for acceptance programmes and test procedures

ST RK 1531-2006: Locomotives of main railways of 1520 mm gage. AC electric rotating tractive machinery. Requirements for acceptance programmes and test procedures

TU 16-525.609-85: Asynchronous motors AIS80 - AIS112, supplied for export. Technical conditions

TU 16-526.562-84: Asynchronous motors with increased slip 4AMS160 - 4AMS250. Technical conditions

VRD 39-1.10-029-2001: Standard programs and methods for conducting preliminary, acceptance and operational tests of electrical units and power plants with a piston and gas turbine drive

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English
Price: $283.00
imgalt
Clear sheet glass. Specifications
Language: English
Price: $250.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!