imgalt

GOST 1983-2001

ГОСТ 1983-2001

Voltage transformers. General specifications

Трансформаторы напряжения. Общие технические условия

Status: Not effective - Superseded. Information about registration 673-st dated 06/23/2016 (official website of Rosstandart); IUS 12-2016

The standard applies to electromagnetic and capacitive voltage transformers (hereinafter referred to as transformers) intended for use in AC electrical circuits with a frequency of 50 or 60 Hz with nominal voltages from 0.38 to 750 kV inclusive for the purpose of transmitting the measurement information signal to measurement, protection, and automation devices , alarm and control. The standard does not apply to laboratory transformers.

Стандарт распространяется на электромагнитные и емкостные трансформаторы напряжения (далее - трансформаторы), предназначенные для применения в электрических цепях переменного тока частотой 50 или 60 Гц с номинальными напряжениями от 0,38 до 750 кВ включительно с целью передачи сигнала измерительной информации приборам измерения, защиты, автоматики, сигнализации и управления. Стандарт не распространяется на лабораторные трансформаторы.

Choose Language: 
Format: Electronic (pdf/doc)

Approved: Gosstandart of Russia, 3/13/2002

SKU: RUSS20909

Price: $532.62



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 29 Electrical Engineering »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.15 Testing and control of products of electronic, optical and electrical industry » 4.15.1 Electric machines, electrical equipment and materials »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 3 Activities of testing laboratories » 3.2 Technical equipment of testing laboratories » 3.2.2 Measuring instruments and test equipment » 3.2.2.4 Instruments for electrical and magnetic measurements »

ISO classifier » 17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA » 17.220 Electricity. Magnetism. Electrical and magnetic measurements » 17.220.20 Measurement of electrical and magnetic quantities »

National standards » 17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA » 17.220 Electricity. Magnetism. Electrical and magnetic measurements » 17.220.20 Measurement of electrical and magnetic quantities »

ISO classifier » 29 ELECTRICAL ENGINEERING » 29.180 Transformers. Reactors »

National standards » 29 ELECTRICAL ENGINEERING » 29.180 Transformers. Reactors »

National Standards for KGS (State Standards Classification) » Latest edition » E Power and electrical equipment » E6 Electric machines, transformers and converters » E64 Transformers »


The Document is Replaced With:

GOST 1983-2015: Voltage transformers. General specifications

As a Replacement Of:

GOST 1983-89: Voltage transformers

The Document References:

GOST 10434-82: Electric contact connections. Classification. General technical requirements

GOST 12.2.007.0-75: Occupation safety standards system Electrical equipment. General safety requirements

GOST 12.2.007.3-75: Occupational safety standard system. Electrotechnical devices for voltage more than 1 000 v

GOST 12.3.019-80: Occupational safety standards system. Electrical tests and measurements. General safety requirements

GOST 13109-97: Electric energy. Electromagnetic compatibility of technical equipment. Power quality limits in public electrical systems

GOST 14192-96: Cargo marking

GOST 15.001-88: System of product development and launching into manufacture. Products of industrial and technical designation

GOST 15.309-98: System of product development and launching into manufacture. Test and acceptance of produced goods. Principal positions

GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence

GOST 1516.1-76: Electrical equipment for ac voltages of 3 to 500 kv

GOST 1516.2-76: Electrical equipment and installations for a. c. voltages 3 kV and higher. General test methods of electrical strength of insulation

GOST 1516.3-96: Electrical equipment for a.c. voltages from 1 to 750 kV. Requirements for dielectric strength of insulation

GOST 15543.1-89: Electrical articles. General requirements for environmental climatic aspects stability

GOST 16504-81: The state system of testing products. Product test and quality inspection. General terms and definitions

GOST 16962.1-89: Electrical articles. Test methods as to environments climatic factors resistance

GOST 16962.2-90: Electrotechnical product

GOST 17516.1-90: Electrical articles. General requirement for environment mechanical stability

GOST 18425-73: Complete, filled transport packages. Vertical impact test by dropping

GOST 18685-73: Current and voltage transformers. Terms and definitions

GOST 19880-74: Electrotechnics. Common concepts. Terms and definitions

GOST 2.601-95: Operational documents

GOST 20074-83: Electrical equipment and installations. Method measurements of partial discharge characteristics

GOST 20690-75: Electrical equipment for a.c. voltage 750 kV. Requirements for electric strength of insulation

GOST 21130-75: Electrical articles. Grounding terminals and grounding signs

GOST 22756-77: Power and voltage transformers and reactors. Test methods of electric insulation strength

GOST 23216-78: Electrotechnical products. Storage, transportation, temporary corrosion protection and packing. General requirements and test methods

GOST 27.003-90: Reliability in engineering. Make-up and general rules for assigning reliability requirements

GOST 3484.1-88: Power transformers. Electromagnetic test methods

GOST 3484.2-88: Power transformers. Heating tests

GOST 3484.5-88: Power transformers. Tank tests for leakages

GOST 6581-75: Liquid electrical insulating materials. Electric test methods

GOST 721-77: Power supply systems, networks, sources,converters and receivers of electric energy. Rated voltages above 1000 V

GOST 8.216-88: State system for ensuring the uniformity of measurements. Voltage transformers. Verification methods

GOST 8865-93: Electrical insulation system. Thermal evalution and classification

GOST 9920-89: A.c. electrical installations for voltage from 3 to 750 kV. Creepage distance of external insulation

GOST R 15.201-2000: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture

GOST R 52002-2003: Electrotechnics. Terms and definitions of basic concepts

RMG 29-99: State system for ensuring the uniformity of measurements. Metrology. Basic terms and definitions

The Document is Referenced By:

GOST 1516.3-96: Electrical equipment for a.c. voltages from 1 to 750 kV. Requirements for dielectric strength of insulation

GOST 23625-2001: Measuring laboratory voltage transformers. General specifications

GOST 30852.17-2002: Explosionproof electrical apparatus. Part 18. Type of protection (m)

GOST 31818.11-2012: Electricity metering equipment (а.с). Particular General requirements. Tests and test conditions. Part 11. Meters for electric energy

GOST 32145-2013: Electric energy. Electromagnetic compatibility of technical equipment. Еlectric energy quality control in the public power supply systems

GOST 33073-2014: Electric energy. Electromagnetic compatibility of technical equipment. Control and monitoring of electric power quality in the public power supply systems

GOST 8.216-2011: State system for ensuring the uniformity of measurement. Potential transformers Checking methods.

GOST 8756.1-79: Canned food products. Methods for determination of organoleptic characteristics, net mass or volume and components fraction of total mass

GOST R 52320-2005: Electricity metering equipment (а.с). General requirements. Tests and test conditions. Part 11. Meters for electric energy

GOST R 52350.18-2006: Electrical apparatus for explosive gas atmospheres. Part 18. Construction, tests and marking of type of protection encapsulation 'm' electrical apparatus

GOST R 53333-2008: Electric energy. Electromagnetic compatibility of technical equipment. Electric energy quality control in the public power supply systems

GOST R 54418.12.1-2011: Wind turbines. Power performance measurements of electricity producing wind turbines

GOST R 54418.21-2011: Renewable power engineering. Wind power engineering. Wind turbines. Part 21. Measurement and assessment of power quality characteristics of grid connected wind turbines

GOST R 54828-2011: Gas-insulated metal-enclosed switchgear for nominal voltages above 110 kV. General technical specification

GOST R 55190-2012: Metal-enclosed switchgear for rated voltages up to and including 35 kV. General specifications

GOST R 55195-2012: Electrical equipment and installations for a.c. voltages from 1 up to 750 kV. Requirements for dielectric strength of insulation

GOST R 55716-2013: High-voltage switchgear. General specifications

GOST R 8.622-2006: State system for ensuring the uniformity of measurements. The quality performances of electric energy. Procedures of measurements during the control of electric energy in the public electrical systems

GOST R 8.746-2011: State system for ensuring the uniformity of measurements. State verification schedule for instruments measuring the ratio error and phase displacement of a.c. power frequency voltage in the range from 0,1/V3 up to 750/V3 kV

GOST R IEC 60079-18-2008: Explosive atmospheres. Part 18. Equipment protection by encapsulation «m»

GOST R IEC 60079-18-2012: Explosive atmospheres. Part 18. Equipment protection by encapsulation «m»

GOST R IEC 61241-18-2009: Electrical apparatus for use in the presence of combustible dust. Part 18. Protection by encapsulation «mD»

Guideline 424: Guidelines for the construction of line structures for backbone and intra-zone cable communication lines (Sections 15-23. Appendices 1-11)

Guideline 424: Guidelines for the construction of line structures for backbone and intra-zone cable communication lines

MI 2159-91: State system for ensuring uniformity of measurements. Direct-on Ammeters and Electrical Measuring Clamps for Alternating Current over 25 A. Calibration Method

MI 2536-99: State system for ensuring uniformity of measurements. Indicators of the quality of electrical energy at metering sites. General requirements for measurement procedures

MI 2808-2003: Recommendation. State system for ensuring uniformity of measurements. The amount of electrical energy. Measurement technique for the distribution of unbalances in the wholesale electricity market

MI 2845-2003: State system for ensuring uniformity of measurements. Measuring voltage transformers 6

MI 2846-2003: State system for ensuring uniformity of measurements. The amount of electrical energy and power. The method of measurement in the branches of OJSC Tyumenenergo

MI 2925-2005: Measuring voltage transformers 35… 330

MI 2982-2006: Recommendation. State system for ensuring uniformity of measurements. Voltage transformers measuring from 500/square root of 3 to 750/square root of 3 kV. On-site verification method

MI 2999-2006: Recommendation. GSOEI. Systems automated information-measuring commercial accounting of electric energy. Recommendations for writing a type description

MI 2999-2011: State system for ensuring uniformity of measurements. Systems automated information-measuring commercial accounting of electric energy. Recommendations for writing a type description

MI 3000-2006: GSOEI. Systems automated information-measuring commercial accounting of electric energy. Typical method of verification

MI 3000-2018: Recommendation. State system for ensuring uniformity of measurements. Systems automated information-measuring commercial accounting of electric energy. Method of verification

MI 3023-2006: Recommendation. State system for ensuring uniformity of measurements. Normalization of the load of the secondary circuits of measuring voltage transformers

MI 3050-2007: State system for ensuring uniformity of measurements. Voltage transformers measuring. Methods of on-site verification using PVE voltage converters

MI 3195-2009: Recommendation. State system for ensuring uniformity of measurements. Load power voltage transformers, the method of measurement without disconnecting circuits

MI 3195-2018: Recommendation. State system for ensuring uniformity of measurements. Method of measuring the load power of measuring voltage transformers under operating conditions

MI 3239-2009: State system for ensuring uniformity of measurements. Measuring voltage transformers. Methods of verification at the site of operation using a three-phase high-voltage calibration installation "Installation of UPTV-3-10"

MI 3314-2011: State system for ensuring uniformity of measurements. Measuring voltage transformers 220

MP 135-2019: System automated information-measuring commercial accounting of electricity (AIIS KUE) PJSC "Penzmash". Verification Method

MP 140-2019: Automated information-measuring system for commercial accounting of electric energy (AIIS KUE) of Transneft PJSC in the part of Transneft Vostok LLC at pump station No. 7

MP 206.1-230-2018: System automated information and measuring commercial accounting of electricity (AIIS KUE) of PJSC

MP 26.51.43/17/19: Automated information-measuring system for commercial metering of electricity of LLC "AUCHAN". Verification method

MP 312235-077-2020: RUSENERGOSBYT LLC automated information measuring system for commercial accounting of electric energy (AIIS KUE) for energy supply of the branch of BUNGE CIS LLC in Kolodeznoye. Verification Method

PNST 159-2016: Automatic information and measuring system of commercial accounting of electric energy. General specifications

RD 153-34.0-15.501-00: Guidelines for monitoring and analyzing the quality of electric energy in general-purpose power supply systems. Part 1. Electrical energy quality control

RD 34.11.333-97: Standard Method for Measurements of Quantity of Electrical Energy

RD 34.35.305-79: Instructions for testing voltage transformers and their secondary circuits

RD 34.47.602-75: Guidelines for the overhaul of the VMD-35 oil circuit breaker

RMG 133-2013: State system for ensuring the uniformity of measurements. The automated data-measuring systems for the commercial metering of electric power. Model verification procedure

SP 226.1326000.2014: Power supply of not traction consumers. Rules for design, construction and renovation

ST RK GOST R 52320-2009: AC electricity metering equipment. General requirements for testing and testing conditions. Part 11. Meters for electric energy

STB GOST R 52320-2007: Equipment for measurement of alternating current of electrical power. General requirements. Tests and test conditions. Part 11. Electrical power recorders

STB IEC 60034-2-1-2011: Electric rotating machines. Part 2-1. Standard defining methods of losses and performance factor at tests (excluding mechanisms for traction vehicles)

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Seamless hot-deformed steel pipes. Specifications
Language: English
Price: $57.42
imgalt
Seamless hot-deformed steel pipes. Range of sizes
Language: English
Price: $77.22
imgalt
Processing equipment and process pipelines
Language: English
Price: $155.43
imgalt
Instructions on Designing of Steel Process Piping, Рnom up to 10 MPa
Language: English
Price: $320.76
imgalt
Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
Language: English
Price: $262.35
imgalt
Federal norms and rules in the field of the use of atomic energy. Valves for nuclear power plants. General technical requirements
Language: English
Price: $1,478.07
imgalt
Unified system for design documentation. Diagrams. Kinds and types. General requirements for fulfillment.
Language: English
Price: $121.77
imgalt
Chemically resistant and heat resistant ceramic wares. The method for determination of heat resistance
Language: English
Price: $34.65
imgalt
Unified system for program documentation. Types of programs and program documents
Language: English
Price: $55.44
imgalt
Petroleum products. Method of test for water-soluble acids and alkalies
Language: English
Price: $48.51
imgalt
Unified system for design documentation. Repair documents
Language: English
Price: $196.02
imgalt
Chemical production safety passport. General requirements
Language: English
Price: $90.09
imgalt
Unified system for design documentation. Exploitative documents
Language: English
Price: $296.01
imgalt
Unified system for design documentation. Types and sets of design documentation
Language: English
Price: $137.61
imgalt
Food products. Methods for detection and quantity determination of coagulase-positive staphylococci and Staphylococcus aureus
Language: English
Price: $223.74
imgalt
Process piping. Standard for the stress, vibration and seismic analysis
Language: English
Price: $879.12
imgalt
Pipeline valves for nuclear stations. General specifications
Language: English
Price: $1,908.72
imgalt
Flanges for valves, fittings and pipelines for pressure to PN 250. Design, dimensions and general technical requirements
Language: English
Price: $703.89
imgalt
Valves of pipeline technological systems of nuclear power plants, not affecting safety. General technical requirements
Language: English
Price: $523.71
imgalt
Fish products. Canned tuna and bonito in water or oil
Language: English
Price: $159.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!