SP 79.13330.2012
СП 79.13330.2012
|
|
Bridges and culverts. Rules of examination and test
Мосты и трубы. Правила обследований и испытаний
Status: Effective
The set of rules applies to surveys, static and dynamic tests and run-in of bridge structures (bridges, overpasses, viaducts, racks, etc.) - further bridges and culverts under embankments — next pipes, designed for moving temporary loads and located on railways , subway and tram lines, highways (including the roads of industrial enterprises), on streets and roads of cities and towns, as well as bridges and pipes, designed for special types of loads (from pipelines, to analov, etc.): surveys and tests carried out after completion of construction (reconstruction, overhaul) upon acceptance of facilities into operation; surveys and tests of structures in operation. The code does not cover: research surveys conducted by project, research and other organizations; for research tests carried out before the stage of destruction of structures; on control inspections and tests of structures, components and parts performed during their manufacture and installation.
Свод правил распространяется на обследования, статические и динамические испытания и обкатку мостовых сооружений (мостов, путепроводов, виадуков, эстакад и т.д.)-далее мосты и водопропускных труб под насыпями-далее трубы, запроектированных под подвижные временные нагрузки и расположенных на железных дорогах, линиях метрополитена и трамвая, автомобильных дорогах (включая дороги промышленных предприятий), на улицах и дорогах городов и населенных пунктов, а также мостов и труб, запроектированных под особые виды нагрузок (от трубопроводов, каналов и др.): обследования и испытания, выполняемые после завершения строительства (реконструкции, капитального ремонта) при приемке сооружений в эксплуатацию; обследования и испытания сооружений, находящихся в эксплуатации. Свод правил не распространяется: на исследовательские обследования, проводимые проектными, научно- исследовательскими и другими организациями; на исследовательские испытания, проводимые до стадии разрушения конструкций; на контрольные обследования и испытания конструкций, узлов и деталей, выполняемые при их изготовлении и монтаже.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Ministry of Regional Development of the Russian Federation,
1/1/2013
SKU: RUSS21138
The Product is Contained in the Following Classifiers:
Construction (Max) »
Regulations »
Documents System of normative documents in construction »
3. Normative documents on urban planning, buildings and constructions »
k.31 Residential, public and industrial buildings and structures »
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Metal structures »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Defects »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
PromExpert »
SECTION III. LABOR PROTECTION AND SAFETY »
III Occupational safety requirements for production equipment and processes »
2 Safety requirements for certain types of work »
2.1 Operation of industrial buildings and structures »
ISO classifier »
93 CIVIL CONSTRUCTION »
93.040 Construction of bridges »
National standards »
93 CIVIL CONSTRUCTION »
93.040 Construction of bridges »
As a Replacement Of:
SP 79.13330.2011: Bridges and culverts. Rules of examination and test
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 10060.0-95: Methods for the determination of frost-resistance. General requirements
GOST 10060-2012: Concretes. Methods for the determination of frost-resistance
GOST 10922-2012: Welded reinforcing products and inserts, welded, lap and mechanical joints for reinforced concrete structures. General specifications
GOST 12.4.011-89: Occupational safety standards system. Means of protection. General requirements and classification
GOST 12004-81: Reinforcing-bar steel. Tensile test methods
GOST 12730.5-84: Concretes. Methods for determination of water tightness
GOST 15140-78: Paintwork materials. Methods for determination of adhesion
GOST 17624-2012: Concrete. Ultrasonic method of strength determination
GOST 17625-83: Reinforced concrete structures and units. Radioactive method of determination of concrete protective covering thickness, reinforcement dimensions and arrangement
GOST 18895-97: Steel. Method of photoelectric spectral analysis
GOST 19912-2012: Soils. Field test methods: cone penetration test and dynamic probing
GOST 22362-77: Reinforced concrete structures. Methods for determination of reinforcement tensioning force
GOST 22690-2015: Concretes. Determination of strength by mechanical methods of non-destructive testing
GOST 22904-93: Reinforced concrete structures. Magnetic method for determining the thickness of the protective layer of concrete and the location of reinforcement
GOST 23858-79: Welded joints butt and T-formed of reinforcement steel bars. Ultrasonic methods of quality inspection. Acceptability requirements
GOST 24846-2012: Soils. Methods of measuring the strains of structures and building bases
GOST 25100-2011: Soils. Classification
GOST 26589-94: Roofing and waterproof mastics. Methods of testing
GOST 28570-90: Concretes. Methods of strength evaluation on cores drilled from structures
GOST 30244-94: Building materials. Methods for combustibility test
GOST 30247.0-94: Elements of building constructions. Fire-resistance test methods. General requirements
GOST 30247.1-94: Elements of building constructions. Fire-resistance test methods. Load bearing and separating constructions
GOST 31149-2014: Paint and varnish materials. Determination of adhesion by the method of cross-cut
GOST 31937-2011: Buildings and constructions. Rules of inspection and of the technical condition
GOST 31993-2013: Paint materials. Determination of film thickness
GOST 3242-79: Welded joints
GOST 33119-2014: Polymer composites constructions for foot-bridges. Specifications
GOST 8829-94: Reinforced concrete and prefabricated concrete building products. Loading test methods. Assesment of strength, rigidity and crack resistance
GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature
GOST R 12.0.010-2009: Occupational safety standards system. Occupational safety and health management systems. Hazard and risks identification and estimation of risks
GOST R 22.1.12-2005: Safety in emergencies. Structured system for monitoring and control of building. Construction engineering equipment. General requirements
GOST R 51694-2000: Paints and varnishes. Determination of film thickness
GOST R 52731-2007: Non-destructive testing. Stress evaluation by ultrasound. General requirements
GOST R 52804-2007: Protection against corrosion of concrete and reinforced concrete constructions. Test methods
GOST R 53778-2010: Buildings and constructions. Rules of inspection and monitoring of the technical condition. General requirements
ODM 218.2.044-2014: Recommendations for the performance of instrument and instrumental measurements in assessing the technical condition of bridge structures on highways
ODM 218.3.001-2010: Recommendations for the diagnosis of active corrosion of reinforcement in reinforced concrete structures of bridges on highways using the half-cell potential method
ODM 218.3.014-2011: Evaluation method for technical condition of bridges and automobile roads.
ODM 218.3.042-2014: Recommendations for determining the parameters and assignment of categories of defects in assessing the technical condition of bridges on highways
ODM 218.4.001-2008: Guidelines for the organization of inspection and testing of bridge structures on highways
ODM 218.4.002-2008: Guidelines for monitoring the status of existing bridge structures
Order 720/pr: On the approval of Amendment No. 2 to SP 79.13330.2012 "SNiP 3.06.07-86 Bridges and pipes. Rules for inspections and tests"
Rules on the Selection of Pressure Vessels and Equipment: Instruction on the selection of pressure vessels and devices operating under pressure of 100 kgf/cm2 and overpressure protection, Ministry of Petroleum Energy
SNiP 12-03-2001: Labor safety in construction industry
SNiP 3.06.07-86: Bridges and Pipes. Rules for Inspection and Testing
SP 126.13330.2012: Survey operations in construction
SP 35.13330.2011: Bridges and pipes. Updated living edition of SNiP 2.05.03-84
SP 46.13330.2012: Bridges and pipes
VSN 1-83: Model Guidelines for Preparation of Data Sheets for and Technical Registration of Public Roads and Highways
VSN 24-88: Technical Guidelines for Road Repair and Maintenance
VSN 32-89: Guidelines for Determining Load Capacity of Reinforced Concrete Beam Span Structures of Road Bridges in Use
VSN 4-81: Inspection Guidelines to Road Overpasses and Underpasses
The Document is Referenced By:
GOST 33119-2014: Polymer composites constructions for foot-bridges. Specifications
GOST R 58137-2018: Automobile roads of general use. Guidelines for risk assessment during the life cycle
GOST R 59488-2021: Automobile roads for general use. Bridge structures. Calculation rules for reinforcing reinforced concrete beam spans
GOST R 59938-2021: Concretes. Acoustic emission test method
MRR 3.2.84-14: The collection of basic prices for work on the inspection of the technical condition of bridge structures, carried out with the involvement of the budget of the city of Moscow
MRR 3.8-16: Inspection of the technical condition of bridges
ODM 218.2.017-2011: Guidelines Design, construction and operation of roads with low traffic
ODM 218.2.037-2013: Guidelines for survey work in the overhaul of roads
ODM 218.2.044-2014: Recommendations for the performance of instrument and instrumental measurements in assessing the technical condition of bridge structures on highways
ODM 218.2.058-2019: Recommendations on the use of composite materials in the construction of bridge structures and pedestrian bridges
ODM 218.2.076-2019: Recommendations on the use of composite structures for areas with extreme temperature conditions (below minus 40 degrees Celsius and above plus 40 degrees Celsius)
ODM 218.2.093-2019: Guidelines for assessing the technical condition and confirming the effectiveness of the use of structures made of polymer composite materials on roads
ODM 218.3.042-2014: Recommendations for determining the parameters and assignment of categories of defects in assessing the technical condition of bridges on highways
ODM 218.3.062-2019: The use of robotic telediagnostic systems for the inspection of culverts and drainage structures on roads
ODM 218.3.089-2019: Guidelines for the experimental use of prestressing reinforcement made of high-strength composite materials for reinforcing reinforced concrete bridge structures
ODM 218.3.095-2017: Corrosion protection of concrete and reinforced concrete structures of transport facilities
ODM 218.3.110-2019: Rules for the development of road maintenance projects
ODM 218.5.009-2008: Technology for magnetic diagnostics of prestressed reinforcement and assessment of the technical condition of reinforced concrete beams of bridge structures
ODM 218.6.030-2017: Recommendations for establishing and warranty periods and service life of structural elements of bridge structures
Order 1112: On Amending Order No. 687 of the Federal Agency for Technical Regulation and Metrology of April 2, 2020
Order 1247: On Amending the Order of the Federal Agency for Technical Regulation and Metrology of April 2, 2020 N 687 "On Approval of the list of documents in the field of standardization, as a result of the application of which on a voluntary basis ensures compliance with the requirements of the Federal Law of December 30, 2009 N 384-FZ "Technical Regulations on the Safety of Buildings and Structures".
Order 1653: On amending the order of the Federal Agency for Technical Regulation and Metrology of April 2, 2020 N 687
Order 720/pr: On the approval of Amendment No. 2 to SP 79.13330.2012 "SNiP 3.06.07-86 Bridges and pipes. Rules for inspections and tests"
PNST 310-2018: Roads are public. Bridges and pipes road. Methods for determining the geometric and physical parameters
PNST 804-2022: Piles. Seismoacoustic method of length and continuity control
Resolution 985: The list of national standards and sets of rules (parts of such standards and sets of rules), as a result of which, on a mandatory basis, compliance with the requirements of the Federal Law "Technical Regulations on the Safety of Buildings and Structures"
RMD 32-24-2015 Sankt-Peterburg: Design of artificial structures at transport facilities in St. Petersburg
SP 229.1325800.2014: Reinforced concrete structures of underground and utility systems. Protection against corrosion
SP 274.1325800.2016: Bridges. Monitoring of technical condition (Structural health monitoring)
SP 35.13330.2011: Bridges and pipes. Updated living edition of SNiP 2.05.03-84
SP 40.13330.2012: Concrete and reinforced concrete dams
SP 443.1325800.2019: Bridges with aluminum alloy structures. Design rules
SP 453.1325800.2019: Artificial high-speed railway lines. Design and construction rules
SP 46.13330.2012: Bridges and pipes
|
Customers Who Viewed This Item Also Viewed:
 |
Petroleum products. Method for measurement of viscosity by automatic capillar viscosimeter
Language: English |
Greases. Method for determination of ultimate strength and thermostrengthening
Language: English |
Pipe fittings. Ball valves made of brass. General specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
