GOST 23118-2012

ГОСТ 23118-2012

Building steel structures. General specifications

Конструкции стальные строительные. Общие технические условия

Status: Effective - Supersedes. IUS 10-2013

The standard applies to steel building structures specified in Section 3 of steel of strength classes not higher than C440 for buildings and structures for various purposes (structures), intended for use in any climatic regions with seismicity up to 9 points inclusive. and establishes general requirements for these structures. The requirements of the standard should be applied in the development of new and revision of existing standards for steel structures for various purposes, the development of working documentation, including, if necessary, special technical conditions for the manufacture and supply of steel structures of specific types and grades. The standard does not apply to structures that play the role of technological equipment (steel structures of blast furnaces and air heaters, tanks and gas holders, radiating structures of antenna structures, head-mounted headframes, structures of lifting and transport equipment and elevators, main and technological pipelines), as well as railway and road bridges and hydraulic structures constructions.

Стандарт распространяется на стальные строительные конструкции, указанные в разделе 3, из стали классов прочности не выше С440 для зданий и сооружений различного назначения (конструкции), предназначенные для применения в любых климатических районах с сейсмичностью до 9 баллов вкпюч. и устанавливает общие требования к этим конструкциям. Требования стандарта следует применять при разработке новых и пересмотре действующих стандартов на стальные конструкции различного назначения, разработке рабочей документации, включающей, при необходимости, специальные технические условия (СТУ) на изготовление и поставку стальных конструкций конкретных типов и марок. Стандарт не распространяется на конструкции, выполняющие роль технологического оборудования (стальные конструкции доменных печей и воздухонагревателей, резервуары и газгольдеры, излучающие конструкции антенных сооружений, надшахтные копры, конструкции подъемнотранспортного оборудования и лифтов, магистральные и технологические трубопроводы), а также железнодорожных и автодорожных мостов и гидротехнических сооружений.

Choose Language: 
Format: Electronic (pdf/doc)
Page Count: 34

Approved: Federal Agency for Technical Regulation and Metrology, 11/29/2012

SKU: RUSS21398

Price: $172.00

The Product is Contained in the Following Classifiers:

Construction (Max) » Regulations » Documents System of normative documents in construction » 5. Regulatory documents for building structures and products » K.53 Metal structures »

Welding regulations » Welding work »

Welding regulations » Main materials »

Welding regulations » Pipelines »

Welding regulations » Metal structures »

Welding regulations » Welding materials »

Welding regulations » Welding staff »

Welding regulations » Admission Testing »

Welding regulations » Certification »

Welding regulations » Documentation »

Welding regulations » Non-destructive control »

Welding regulations » Mechanical Testing »

Welding regulations » Heat treatment »

Welding regulations » Defects »

Welding regulations » Assembly devices »

Welding regulations » Welding work » Mechanized welding »

Welding regulations » Welding work » Automatic welding »

Welding regulations » Welding work » Surfacing »

Welding regulations » Welding work » Dusting »

Welding regulations » Main materials » Steel, cast iron »

Welding regulations » Welding materials » Electrodes »

Welding regulations » Welding materials » Wire »

Welding regulations » Welding materials » Fluxes »

Welding regulations » Welding materials » Gases »

ISO classifier » 91 CONSTRUCTION MATERIALS AND CONSTRUCTION » 91.080 Structures of buildings » 91.080.10 Metal constructions »

National standards » 91 CONSTRUCTION MATERIALS AND CONSTRUCTION » 91.080 Structures of buildings » 91.080.10 Metal constructions »

National Standards for KGS (State Standards Classification) » Latest edition » Zh Construction and building materials » Zh3 Building structures and parts » Zh34 Metal structures and parts »

The Document is Replaced With:

GOST 23118-2019: Steel building structures. General specifications

As a Replacement Of:

GOST 23118-99: Steel construction structures General Technical Specifications

The Document References:

GOST 11533-75: Automatic and semiautomatic submerged arc welding. Acute and blunt weld joints. Main types, design elements and dimensions

GOST 11534-75: Hand arc welding. Acute and blunt weld joints. Main types, design elements and dimensions

GOST 12.3.009-76: Occupational safety standards system. Loading and unloading works General safety requirements

GOST 14192-96: Cargo marking

GOST 14771-76: Gas-shielded arc welding. Welded joints. Main types, design elements and dimensions

GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods

GOST 15.005-86: Creation of articles manufactured individually or in small batches and assembled at the place of operation

GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence

GOST 1759.0-87: Bolts, screws, studs and nuts. Specifications.

GOST 18160-72: Fasteners. Packing. Marking. Transportation and storage

GOST 2.314-68: Unified system for design documentation. Instructions for marking and stamping articles

GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements

GOST 21778-81: System of ensuring of geometrical parameters accuracy in construction. Main principles

GOST 21779-82: System of ensuring of geometrical parameters accuracy in construction. Manufacturing and assembling tolerances

GOST 21780-2006: System of ensuring the accuracy of geometrical parameters in construction. Accuracy calculation

GOST 22235-2010: Freight cars for 1520 mm gauge main line railways. General requirements for safety in loading-unloading and shunting operations

GOST 22353-77: High strength bolts of product grade B. Construction and dimensions

GOST 22356-77: High strength bolts and nuts аnd washes. General specifications

GOST 23518-79: Cas-shielded arc welding. Welded joints. Main types, design elements and dimensions

GOST 23616-79: System of ensuring of geometrical accuracy of parameters in construction. Control of accuracy

GOST 24297-87: Input inspection of products. General provisions.

GOST 25726-83: Letter and numerical hand stamps. Types and basic dimensions

GOST 26047-83: Building steel structures

GOST 26433.1-89: System of ensuring geometrical parameters accuracy in construction. Rules of measurement. Prefabricated elements

GOST 26433.2-94: System of ensuring geometric parameters accuracy in building. Rules for measuring parameters of buildings and works

GOST 27751-88: Reliability of the constructions and the foundations. Principal rules of the calculations

GOST 5264-80: Manual are welding. Welding joints. Main types, design elements and dimensions

GOST 6996-66: Welded joints. Methods of mechanical properties determination

GOST 7512-82: Nondestructive testing. Welded joints. Radiography method

GOST 8713-79: Flux welding. Welded joints. Maih types design elements and dimensions

GOST 9.032-74: Unified, system of corrosion and ageing protection. Paint coatings. Groups, technical requirements and designations

GOST 9.302-88: Unified system of corrosion and ageing protection. Metal and non-metal inorganic coatings. Control methods

GOST 9.402-2004: Unified system of corrosion and ageing protection. Paint coatings. Metal surface preparation for painting

GOST R 15.201-2000: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture

GOST R 52643-2006: High-strength screws and nuts washers for metal structures. General specifications

GOST R 52644-2006: Hexagon bolts for high-strength structural bolting with large width across flats. Specifications.

GOST R 54257-2010: Reliability of the constructions and foundations. Basic principles and requirements

SP 16.13330.2011: Steel structures

SP 28.13330.2012: Corrosion protection of buildings structures. Updated living edition of SNiP 2.03.11-85

SP 50.13330.2012: Buildings Heat Insulation. Updated living edition of SNiP 23-02-2003

The Document is Referenced By:

GOST 19330-2013: Masts (poles) for overhead contact line supports of railways. Specifications

GOST 21.502-2016: System of building design documents. Rules for the implementation of working documentation for metal structures

GOST 22130-2018: Steel piping details. Movable supports and hangers. Specifications

GOST 23120-2016: Stairways, marching, platforms and fences of steel. Specification

GOST 24741-2016: Joint for connection of crane rails to steel crane girders. Specifications

GOST 26429-2018: Steel structures of suspended transport tracks. Specifications

GOST 31173-2016: Steel doors. Specifications

GOST 31174-2017: Gates of metall. General specifications

GOST 32623-2014: Automatic tensioning devices of overhead contact line of railway. General specifications

GOST 33797-2016: Cross beams of rigid portals for overhead contact line of railway transport. General specifications

GOST 33807-2016: Safety of attractions. General requirements

GOST 34433-2018: Trunk pipelines for oil and oil products transportation. Transformer complete substations with voltage from 35 to 220 kV. General specifications

GOST 34613-2019: Protective cabin. General technical requirements and test methods

GOST R 51222-98: Equipment for bank protection. Venetian blinds. General specifications

GOST R 55186-2012: Cross beams of rigid portals for overhead contact line of railway transport. General specifications

GOST R 55525-2017: Storage systems. Adjustable pallet racking. General specifications

GOST R 57381-2017: Storage systems. Hand loaded steel static shelving. General specifications

GOST R 57991-2017: Trunk pipeline transport of oil and oil products. Steel piles of pipes used for foundation construction of above-ground pipelines supports. General specifications

GOST R 58064-2018: Steel welded pipes for building structure. Technical specifications

GOST R 58351-2019: General automobile roads. Frontal road fences, holding lateral combined and holding pedestrian. General technical requirements. Testing and control methods. Application rules

ODM 218.2.087-2017: Recommendations for the design and construction of culverts of spiral-wavy metal corrugated pipes

PNST 310-2018: Roads are public. Bridges and pipes road. Methods for determining the geometric and physical parameters

PNST 320-2018: Bearing structures of railway signaling devices. General technical requirements

PNST 353-2019: General automobile roads. Expansion joints with rubber compensator spans for road bridges. General specifications

RMD 12-21-2013 Sankt-Peterburg: Typical temporary means of fencing, arranging and decorating construction sites

SP 25.13330.2020: Bases and foundations on permafrost soil SNiP 2.02.04-88

SP 260.1325800.2016: Cold-formed thin-walled steel profile and galvanized corrugated plate constructions. Design rules

SP 265.1325800.2016: Manifold for engineering networks

SP 266.1325800.2016: Composite steel and concrete structures. Design rules

SP 267.1325800.2016: High rise buildings and complexes. Design rules

SP 294.1325800.2017: The construction of steel. Design rules

SP 315.1325800.2017: Thermal networks laid in a ground. Design rules

SP 363.1325800.2017: Translucent coating and lights of buildings and structures. Desing rules

SP 369.1325800.2017: Fixed offshore platforms. Design principles

SP 443.1325800.2019: Bridges with aluminum alloy structures. Design rules

SP 46.13330.2012: Bridges and pipes

SP 470.1325800.2019: Steel structures. Work Rules

SP 70.13330.2012: Bearing and enclosing structures. Updated living edition of SNiP 3.03.01-87

SP 76.13330.2016: Electrical systems

SP 83.13330.2016: Industrial furnaces and brick chimneys

STO Basic rules for ensuring the operation of nuclear power plants

Customers Who Viewed This Item Also Viewed:

Special railway rolling stok. Dynamic and strength testing procedures
Language: English
Price: $198.00
Blanks for marine shafts and rudder stocks. Specifications
Language: English
Price: $216.00
Tempered glass. Specifications.
Language: English
Price: $149.00
Glass with low emissivity hard coating. Specifications.
Language: English
Price: $212.00
Glass laminated. Specifications.
Language: English
Price: $231.00


RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!