imgalt

GOST 10922-75

ГОСТ 10922-75

Reinforcement products and embedded parts, welded for reinforced concrete structures. Requirements and test methods

Арматурные изделия и закладные детали сварные для железобетонных конструкций. Технические требования и методы испытаний

Status: Not effective - Superseded

The standard applies to welded reinforcement products (grids, frames and individual rods with welded joints), embedded parts, as well as welded joints (butt, cross-shaped, tee and overlap), used in the manufacture and installation of concrete structures. The standard establishes the technical requirements for reinforcement products, embedded parts, welded joints, the rules for their acceptance and methods of mechanical testing of welded joints. The standard does not apply to welded wire mesh with a diameter of less than 3 mm.

Стандарт распространяется на сварные арматурные изделия (сетки, каркасы и отдельные стержни со сварными соединениями), закладные детали, а также на сварные соединения (стыковые, крестообразные, тавровые и нахлесточные), применяемые при изготовлении и монтаже железобетонных конструкций. Стандарт устанавливает технические требования к арматурным изделиям, закладным деталям, сварным соединениям, правила их приемки и методы механических испытаний сварных соединений. Стандарт не распространяется на сварные сетки из проволоки диаметром менее 3 мм.

Choose Language: 
Format: Electronic (pdf/doc)

Approved: State Committee of the Council of Ministers of the USSR for Construction, 7/26/1975

SKU: RUSS223880




Price: imgalt
imgalt

The Product is Contained in the Following Classifiers:

Welding regulations » Metal structures »

National Standards for KGS (State Standards Classification) » Latest edition » Zh Construction and building materials » Zh3 Building structures and parts » Zh33 Stone, brick, concrete and reinforced concrete structures and parts »


The Document is Replaced With:

GOST 10922-90: Welded reinforcing products and inserts, welded joints of reinforcement and inserts for reinforced concrete structures. General specifications

As a Replacement Of:

GOST 10922-64: Armature products and embedded parts, welded for reinforced concrete structures. Requirements and test methods

The Document References:

GOST 12004-81: Reinforcing-bar steel. Tensile test methods

GOST 14098-68: Welded reinforcement joints of reinforced concrete products and structures. Contact and bath welding. Main types and structural elements

GOST 19292-73: Welded joints of embedded parts of prefabricated reinforced concrete structures. Contact and automatic welding by melting. Main types and structural elements

GOST 19293-73: Welded reinforcement joints of prestressed reinforced concrete structures. Contact and melt welding. Main types and structural elements

GOST 8478-81: Welded meshes for reinforced concrete structures. Specifications

The Document is Referenced By:

GOST 10884-81: Heat strengthened steel bars of periodical section for concrete reinforcement. Technical requirements

GOST 11024-72: Panels made of lightweight concrete for exterior walls of residential and public buildings. Technical requirements

GOST 13015.0-83: Prefabricated concrete and reinforced concrete constructions and products. General technical requirements

GOST 13015.1-81: Prefabricated concrete and reinforced concrete constructions and products. Acceptance

GOST 14098-68: Welded reinforcement joints of reinforced concrete products and structures. Contact and bath welding. Main types and structural elements

GOST 14098-85: Welded joints of reinforcement and inserts for reinforced concrete structures. Types, construction and dimensions

GOST 18979-90: Reinforced concrete columns for multi-storey buildings. Specifications

GOST 18980-73: Reinforced concrete locks for buildings. Technical requirements

GOST 19222-84: Arbolit and its products. General specifications

GOST 19292-73: Welded joints of embedded parts of prefabricated reinforced concrete structures. Contact and automatic welding by melting. Main types and structural elements

GOST 19293-73: Welded reinforcement joints of prestressed reinforced concrete structures. Contact and melt welding. Main types and structural elements

GOST 21509-76: Reinforced concrete shoots for irrigation systems. Specifications

GOST 22362-77: Reinforced concrete structures. Methods for determination of reinforcement tensioning force

GOST 22687.3-85: Racks reinforced concrete centrifuged for supports of high-voltage power lines. The design of embedded products and thrust bearings

GOST 22930-87: Prestressed reinforced concrete slabs for irrigation canal lining of melioration systems. Specifications

GOST 23858-79: Welded joints butt and T-formed of reinforcement steel bars. Ultrasonic methods of quality inspection. Acceptability requirements

GOST 24594-81: Wall panels and blocks of brick and ceramic stones. General specifications

GOST 28042-89: Reinforced concrete roofing for enterprises buildings. Specifications

GOST 6665-82: Concrete and reinforced concrete stones. Specification

GOST 6665-91: Concrete and Reinforced Concrete Curbs. Specifications

GOST 948-76: Reinforced concrete jumpers for buildings with brick walls. Specification

GOST 9561-76: Panels of reinforced-concrete hollow-core for floors of buildings. Specification

GOST 9818.0-81: Reinforced concrete flights of steps and stair landings. General specifications

Recommendations: Aspiration smoke-sensitive alarms VESDA. Part 1. Scope

RSN 342-86: Technology for reinforcing building structures in reconstructed enterprises

Series 1.132.1-13pv: External wall panels lightweight concrete single-layer single-row cutting for large-panel residential buildings with a step of transverse walls of 3.0; 3.6 m and a floor height of 2.8 m (unified for difficult construction conditions: unevenly compressible soils, subsidence soils, undermined areas)

Series 1.132.1-13pv: Issue 0. Materials for design. Instructions for the manufacture of panels. Panel Assemblies

Series 1.132.1-13pv: Issue 1. One-step panels. Working drawings

Series 1.132.1-13pv: Issue 2. The panels are two-step. Working drawings

Series 1.132.1-13pv: Issue 3. Reinforcing and embedded products. Working drawings

SNiP 2.03.01-84 Reference Manual: Reference manual on design of concrete and reinforced concrete structures made of heavy and light concrete without reinforcement prestressing

SNiP 3.03.01-87: Bearing and enclosing structures

TU 33 UzSSR 01-84: Products from lightweight concrete based on slag-alkali binders. Technical specifications

TU 33-82-86: Plates flat with reinforcement outlets

VRD 66-91-85: Guidelines for the quality control of welding work on construction sites

VSN 01-76/USSR Mintsvetmet: Instructions for the design and installation of bored piles in permafrost soils of the Norilsk region

VSN 06-77/USSR Minselstroy: Instructions for the manufacture of two-layer wall panels and blocks of lightweight concrete for agricultural buildings in series 1.832-5

VSN 34-91/MT-st: Execution and Acceptance Requirements for New Construction, Rehabilitation, and Expansion of Existing Marine and River Hydraulic Transport Structures. Part I: Part II: Part III

VSN 3-80/Minmorflot: Instructions for the design of offshore berthing facilities

VSN 48-93: Installation Manual for Cast-In-Place Concrete and Reinforced Concrete Tunnel Lining for Transportation Tunnels

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Jet fuels
Language: English
Price: $49.00
imgalt
Chill moulds. Ventilation channels. Dimensions
Language: English
Price: $68.00
imgalt
Laminated glued wood. Methods for determination of ultimate and modulus of elasticity in static bending
Language: English
Price: $151.00
imgalt
Microbiology of food and animal feeding stuffs. Methods for detection and enumeration of sulphite-reducing bacteria growing under anaerobic conditions
Language: English
Price: $154.00
imgalt
Rails of types P38 and P42. Technical conditions
Language: English
Price: $109.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!