GOST 33929-2016

ГОСТ 33929-2016

Concrete with polysterene aggregates. Specifications

Полистиролбетон. Технические условия

Status: Effective - Introduced for the first time. IUS 2-2017; the date of introduction was postponed from 01/01/2017 to 01/01/2018; IUS 6-2017

The standard applies to particularly lightweight concrete porous structure on cement binder and porous filler of polystyrene foam granules, intended for the manufacture of precast products or monolithic structures used in exterior walls, coatings and ceilings of energy-efficient residential and public buildings. In a feasibility study, it is allowed to use polystyrene concrete for industrial, road and other types of construction. Recommended scopes of polystyrene concrete in building envelopes are given in Appendix A. The standard establishes technical requirements for polystyrene concrete and polystyrene concrete mixtures, materials for their preparation, as well as for acceptance and control methods of their technical characteristics. The requirements of the standard should be considered in the new and revised standards and technical specifications for prefabricated products and monolithic structures made of polystyrene concrete.

Стандарт распространяется на особо легкий бетон поризованной структуры на цементном вяжущем и пористом заполнителе из вспененных гранул полистирола, предназначенный для изготовления сборных изделий или монолитных конструкций, применяемых в наружных стенах, покрытиях и перекрытиях энергоэффективных жилых и общественных зданий. При технико-экономическом обосновании допускается применение полистиролбетона для конструкций промышленного, дорожного и других видов строительства. Рекомендуемые области применения полистиролбетона в ограждающих конструкциях зданий приведены в приложении А. Стандарт устанавливает технические требования к полистиролбетону и полистиролбетонным смесям, материалам для их приготовления, а также к приемке и методам контроля их технических характеристик. Требования стандарта следует учитывать в разрабатываемых новых и пересматриваемых стандартах и технических условиях на сборные изделия и монолитные конструкции из полистиролбетона.

Choose Language: 
Format: Electronic (pdf/doc)
Page Count: 24

Approved: Federal Agency for Technical Regulation and Metrology, 10/20/2016

SKU: RUSS243324

Price: $363.78




The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 91 Building materials and construction »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 2 Tests for external factors » 2.3 Testing of products in construction »

ISO classifier » 91 CONSTRUCTION MATERIALS AND CONSTRUCTION » 91.100 Building Materials » 91.100.30 Concrete and concrete products »

National standards » 91 CONSTRUCTION MATERIALS AND CONSTRUCTION » 91.100 Building Materials » 91.100.30 Concrete and concrete products »


The Document References:

GN 2.2.5.1313-03: Maximum allowable concentrations (MACs) of harmful substances in occupational air

GOST 10060-2012: Concretes. Methods for the determination of frost-resistance

GOST 10178-85: Portland cement and portland blastfurnace slag cement. Specifications

GOST 10180-2012: Concretes. Methods for strength determination using reference specimens

GOST 10181-2014: Concrete mixtures. Methods of testing

GOST 12.1.044-89: Fire and explosion hazard of substances and materials. Nomenclature of indices and methods of their determination

GOST 12730.1-78: Concretes. Methods of determination of density

GOST 12730.2-78: Concretes. Method of determination of moisture content

GOST 12730.4-78: Concretes. Methods of determination of porosity parameters

GOST 13015-2012: Concrete and reinforced concrete products for construction. General technical requirements. Rules for acceptance, marking, transportation and storage

GOST 18105-2010: Concretes. Rules of control and norm of an assessment of quality.

GOST 23732-2011: Water for concretes and cement mortars Technical specifications.

GOST 24211-2008: Admixtures for concretes and mortars. General specifications

GOST 24452-80: Concretes. Methods of prismatic compressive strengths, modulus of elasticity and Poisson ratio determination

GOST 24544-81: Concretes. Methods for determining shrinkage and creep deformations

GOST 25192-2012: Concretes. Classification and general technical requirements

GOST 25818-91: Thermal plant fly-ashes for concretes. Specifications

GOST 25898-2012: Building materials and products. Methods for determination of water vapour permeability and of steam-tightness

GOST 27005-2014: Light-weight and cellular concretes. Rules for control and assessment density

GOST 27006-86: Concretes. Rules for mix proportioning

GOST 28013-98: Mortars. General specifications

GOST 30108-94: Building materials and elements. Determination of specific activity of natural radioactive nuclei

GOST 30244-94: Building materials. Methods for combustibility test

GOST 30402-96: Building materials Ignitability Test Meth

GOST 31108-2016: General structural Portland clinker cements. Specifications

GOST 31359-2007: Cellular autoclave curing concretes. Specifications

GOST 3476-74: Slags domain and electrothermophosphoric granulated for the production of cements

GOST 4.212-80: Product-quality index system. Building. Concretes. Nomenclature of indices

GOST 5802-86: Mortars. Test methods.

GOST 6139-2003: Sand for cement testing. Specifications

GOST 7076-99: Building materials and products. Method of determination of steady-state thermal conductivity and thermal resistance

GOST 7473-2010: Fresh concrete. Specifications

GOST 8735-88: Sand for construction work. Testing methods

GOST 9758-2012: Porous inorganic aggregates for construction work. Test methods

MU 2.1.2.1829-04: Sanitary and hygienic assessment of polymer and polymer-containing building materials and structures intended for use in the construction of residential, public and industrial buildings

SanPiN 2.1.2.729-99: Polymer and polymer containing construction. Materials. Products and structures. Hygienic requirements

SanPiN 2.1.7.1322-03: Hygienic requirements regarding dumping and decontamination of industrial and consumable waste

SanPiN 2.6.1.2523-09: Norms of radiation safety

The Document is Referenced By:

SP 15.13330.2012: Masonry and reinforced masonry structures

SP 327.1325800.2017: Exterior masonry walls with brick veneer. Rules of design, operation and repair

SP 50.13330.2012: Buildings Heat Insulation. Updated living edition of SNiP 23-02-2003

GOST 19222-2019: Arbolit and products from it. General specifications

SP 434.1325800.2018: Polystyrene concrete enclosures. Design rules

Customers Who Viewed This Item Also Viewed:

Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
Language: English
Price: $262.35
Locomotive and motor rolling stock. Requirements of fire safety
Language: English
Price: $305.50
Unified system of design documentation. Operational documents
Language: English
Price: $610.13
Unified system of design documentation. Rules for the implementation of operational documents
Language: English
Price: $752.72
Noise. Admissible levels of noise in houses and public buildings
Language: English
Price: $7.52
System of building design document. Pipelines. Symbols for presentation
Language: English
Price: $10.89
Electrical equipment for a.c. voltages from 1 to 750 kV. Requirements for dielectric strength of insulation
Language: English
Price: $267.30
Electrical articles. General requirement for environment mechanical stability
Language: English
Price: $28.20
Machines for the pulp and paper industry
Language: English
Price: $207.58
Unified system for design documentation. Rules for making exploitative documents
Language: English
Price: $183.15
Electrical insulation system. Thermal evalution and classification
Language: English
Price: $54.45
Fire hazard of textiles. Decorative textiles. Flammability test method and classification
Language: English
Price: $49.50
Loads and impacts
Language: English
Price: $338.40
Direct-acting safety valves. General specifications
Language: English
Price: $346.50
Technical regulations of Customs Union. On the safety of agricultural and forestry tractors and trailers
Language: English
Price: $98.40
Seamless cold-deformed pipes from alloys based on titanium. Specifications
Language: English
Price: $147.44
Flame arrestors and spark arrestors. General technical requirements. Test methods
Language: English
Price: $128.70
Production conditions analysis for product attestation
Language: English
Price: $285.18
Vibration. Technological equipment of pulp and paper production. Protection methods and means
Language: English
Price: $299.73
Steel. Methods of test and estimation of macrostructure
Language: English
Price: $148.50

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message live-chat-up-arrow live-chat-down-arrow

Leave your message in the form below, and we will write back by e-mail!