GOST 33752-2017
ГОСТ 33752-2017
|
|
Steel welded cylinders for liquefied hydrocarbon gas, used as motor fuel on automotive vehicle. Specifications
Баллоны стальные сварные для сжиженных углеводородных газов, используемых в качестве моторного топлива на механических транспортных средствах. Технические условия
Status: Effective - Introduced for the first time. IUS 11-2017
This standard establishes minimum requirements for materials, construction and quality of manufacturing steel welded cylinders without valves with a working pressure of up to 2.0 MPa and a nominal capacity of up to 350 liters inclusive, intended for liquefied hydrocarbon gases used as motor fuel in motor vehicles. The temperature of the safe operation of cylinders manufactured according to this standard should be in the range of minus 40
Настоящий стандарт устанавливает минимальные требования к материалам, конструкции и качеству изготовления стальных сварных баллонов без арматуры с рабочим давлением до 2,0 МПа, номинальной вместимостью до 350 л включительно, предназначенных для сжиженных углеводородных газов, используемых в качестве моторного топлива на механических транспортных средствах. Температура безопасной эксплуатации баллонов, изготовленных по настоящему стандарту, должна находиться в диапазоне от минус 40
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
6/30/2017
SKU: RUSS286551
The Product is Contained in the Following Classifiers:
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Welding materials »
Welding regulations »
welding equipment »
Welding regulations »
Welding staff »
Welding regulations »
Admission Testing »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Defects »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Main materials »
Non-ferrous metals »
Welding regulations »
Welding materials »
Gases »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.12 Testing and control of products of metallurgical industry »
4.12.6 Metal products »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.020 Storage tanks for liquids and gases »
23.020.30 Pressure vessels, gas cylinders »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.020 Storage tanks for liquids and gases »
23.020.30 Pressure vessels, gas cylinders »
The Document References:
GOST 10006-80: Metal pipes
GOST 1050-2013: Metal products from nonalloyed structural quality and special steels. General specification
GOST 13078-81: Sodium glass liquid. Technical conditions
GOST 14249-89: Vessels and apparatus. Norms and methods of strength calculation
GOST 14637-89: Thick sheet rolled stock of normal quality carbon steel
GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods
GOST 1497-84: Metals. Methods of tension test
GOST 15.309-98: System of product development and launching into manufacture. Test and acceptance of produced goods. Principal positions
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 16523-97: Rolled sheets from quality and ordinary carbon steel for general purposes. Specifications
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 19151-73: Red lead. Specifications
GOST 19903-2015: Hot-rolled sheet. Range
GOST 19904-90: Cold-rolled steel sheets. Dimensions
GOST 2.001-2013: Unified system for design documentation. General principles
GOST 2016-86: Thread gauges. Specifications
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 23055-78: Non-destructive testing. Fusion welding of metals. Welds classification by radiography testing results
GOST 24297-2013: Verification of purchased product. Organization and methods of control
GOST 24705-2004: Вasic norms of interchangeability. Metric screw thread. Basic dimensions
GOST 24997-2004: Gauges for metric thread. Tolerances
GOST 24998-81: Gauges for tapes thread of valves and gas-bags. Tolerances
GOST 25859-83: Steel vessels and apparatuses. Norms and methods of fatigue strength calculation under low-cyclic loads
GOST 27578-87: Liquefied hydrocarbon gases for motor transport gases
GOST 3.1001-2011: Unified system for technological documentation. General principles
GOST 3242-79: Welded joints
GOST 380-2005: Common quality carbon steel. Grades
GOST 5539-73: Litharge. Specifications
GOST 5639-82: Steel and alloys. Methods for detection and determination of grain size
GOST 6996-66: Welded joints. Methods of mechanical properties determination
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 7931-76: Natural drying oil
GOST 8253-79: Calcium carbonate precipitated. Specifications
GOST 9.032-74: Unified, system of corrosion and ageing protection. Paint coatings. Groups, technical requirements and designations
GOST 9.402-2004: Unified system of corrosion and ageing protection. Paint coatings. Metal surface preparation for painting
GOST 9.410-88: Unified system of corrosion and ageing protection. Powder polymeric coatings. Typical technological processes
GOST 9909-81: Basic norms of interchangeability. Taper screw thread of valves and gas cylinder
GOST R 55724-2013: Non-destructive Testing. Welded Joints. Ultrasonic Methods
GOST R 56512-2015: Non-destructive testing. Method of magnetic particle testing. Standard technological processes
|
Customers Who Viewed This Item Also Viewed:
 |
Jet fuels
Language: English |
State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 5. Measurement procedure
Language: English |
Molded parts of coupler and automatic coupler devices of railway rolling stock. General specifications.
Language: English |
Main-line diesel locomotives. General technical requirements.
Language: English |
Four-wheel bogies of freight cars for mainline railways gauge 1520 (1524) mm. Specifications
Language: English |
Technical ethylcellosolve. Specifications
Language: English |
Automatic coupler model SA-3 and its components. Design and dimensions
Language: English |
Railway rolling stock. Devices to prevent running gear parts from dropping to the track. Methods of controlling strength characteristics
Language: English |
Electric heating devices for heating rolling stock railways. Safety requirements and test methods
Language: English |
Ice cream. General technical requirements
Language: English |
Welded joints in steel structures of railway rolling stock. Requirements for design, implementation and quality control
Language: English |
Locomotives The method of dynamic strength tests
Language: English |
Railway rolling stock. Norms for permissible exposure of railway track and test methods
Language: English |
Locomotives. Requirements for strength and dynamic qualities
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
