imgalt

GOST 34011-2016

ГОСТ 34011-2016

Gas distribution systems. Block gas delivery stations. Cabinet gas delivery stations. General technical requirements

Системы газораспределительные. Пункты газорегуляторные блочные. Пункты редуцирования газа шкафные. Общие технические требования

Status: Effective - Introduced for the first time. IUS 8-2017

This standard applies to gas control block and gas reduction points cabinet (hereinafter referred to as gas reduction points), designed to reduce the pressure of natural gas from the input value (up to 1.2 MPa inclusive) to the required values, as well as to perform the following functions: -automatic maintaining a given output pressure regardless of the change in flow rate and gas inlet pressure (in a given range of their values), -automatically stop the flow of gas with increasing or decreasing output a pressure in excess of or below the permissible set values, -Cleaning gas from mechanical impurities -Accounting gas. This standard establishes general technical requirements for gas reduction points intended for use in gas distribution networks and gas consumption in the transportation of combustible gases according to GOST 5542. This standard does not apply to gas control units, stationary gas control points, as well as gas reduction points that have been commissioned before date of entry into force of this standard

Настоящий стандарт распространяется на пункты газорегуляторные блочные и пункты редуцирования газа шкафные (далее-пункты редуцирования газа), предназначенные для редуцирования давления природного газа с входного значения (до 1,2 МПа включительно) до требуемых значений, а также для выполнения следующих функций: -автоматического поддержания заданного выходного давления независимо от изменения расхода и входного давления газа (в заданном диапазоне их значений), -автоматического прекращения подачи газа при повышении или понижении выходного давления сверх или ниже допустимых заданных значений, -очистки газа от механических примесей, -учета газа. Настоящий стандарт устанавливает общие технические требования к пунктам редуцирования газа, предназначенным для применения в сетях газораспределения и газопотребления при транспортировании горючих газов по ГОСТ 5542. Настоящий стандарт не распространяется на газорегуляторные установки, стационарные газорегуляторные пункты, а также на пункты редуцирования газа, принятые в эксплуатацию до дня вступления в силу настоящего стандарта

Choose Language: 
Format: Electronic (pdf/doc)

Approved: Federal Agency for Technical Regulation and Metrology, 4/13/2017

SKU: RUSS286623

Price: $398.00



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 75 Extraction and processing of oil, gas and related production »

Welding regulations » Welding work »

Welding regulations » Main materials »

Welding regulations » Pipelines »

Welding regulations » Metal structures »

Welding regulations » Welding materials »

Welding regulations » welding equipment »

Welding regulations » Documentation »

Welding regulations » Non-destructive control »

Welding regulations » Defects »

Welding regulations » Welding work » Dusting »

Welding regulations » Main materials » Steel, cast iron »

Welding regulations » Welding materials » Gases »

ISO classifier » 75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION » 75.180 Equipment for oil and gas industry » 75.180.99 Other equipment for oil and gas industry »

National standards » 75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION » 75.180 Equipment for oil and gas industry » 75.180.99 Other equipment for oil and gas industry »


The Document is Replaced With:

GOST 34011-2024: Gas distribution systems. Gas regulator units. Closet gas reducing units. General technical requirements

The Document References:

GOST 5264-80: Manual arc welding. Welding joints. Main types, design elements and dimensions

GOST 10549-80: Screw thread runout. Washout threads, total thread runouts, undercuts and chamfers

GOST 11534-75: Hand arc welding. Acute and blunt weld joints. Main types, design elements and dimensions

GOST 11881-76: Controllers acting without

GOST 12.1.004-91: Fire safety. General requirements

GOST 12.1.010-76: Explosion safety. General requirements

GOST 12.1.019-79: Occupational safety standards system. Electric safety. General requirements and nomenclature of kinds of protection

GOST 12.2.003-91: Industrial equipment. General safety requirements

GOST 12.2.063-81: Occupational safety standards system. Industrial pipeline valves. General safety requirements

GOST 12.2.091-2012: Safety requirements for electrical equipment for measurement, control and laboratory use. Part 1. General requirements

GOST 12815-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). Types. Connecting dimensions and dimensions of sealing surfaces

GOST 12816-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). General technical requirements

GOST 12817-80: Cast grey iron flanges for Pnom from 0,1 to 1,6 MPa (from 1 to 16 kgf/sq sm). Design and dimensions

GOST 12818-80: Cast malleable iron flanges for Pnom from 1,6 to 4,0 MPa (from 16 to 40 kgf/cm2). Design and dimensions

GOST 12819-80: Cast steel flanges for Pnom from 1,6 to 20,0 MPa (from 16 to 200 kgf/sq sm). Design and dimensions

GOST 12820-80: Steel plane welded flanges for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/cm2). Design and dimensions

GOST 12821-80: Steel butt-welded flanges for Pnom from 0,1 to 20,0 MPa (from 1 to 200 kgf/cm2). Design and dimensions

GOST 12822-80: Steel loose flanges with welded ring for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/sq sm). Design and dimensions

GOST 14192-96: Cargo marking

GOST 14776-79: Arc welding. Button welds. Main types, design elements and dimensions

GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods

GOST 15.309-98: System of product development and launching into manufacture. Test and acceptance of produced goods. Principal positions

GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence

GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage

GOST 16037-80: Welded joints in steel pipelines. Main types, design elements and dimensions

GOST 16093-2004: Basic norms of interchangeability. Metric screw thread. Tolerances. Clearance fits

GOST 17375-2001: Carbon and low-alloy steel butt-welding fittings. Sharply curved bends type 3D (R=1,5 DN). Design

GOST 17376-2001: Carbon and low-alloy steel butt-welding fittings. Tees. Design

GOST 17378-2001: Carbon and low-alloy steel butt-welding fittings. Reducers. Design

GOST 17379-2001: Carbon and low-alloy steel butt-welding fittings. Elliptical caps. Design

GOST 17380-2001: Carbon and low-alloy steel butt-welding fittings. General specifications

GOST 21130-75: Electrical articles. Grounding terminals and grounding signs

GOST 24597-81: Unitized tared and piece goods cargoes. Main parameters and dimensions

GOST 24705-2004: Вasic norms of interchangeability. Metric screw thread. Basic dimensions

GOST 30331.3-95: Electrical installations of buildings. Part 4. Protection for safety. Protection against electric shock

GOST 30546.1-98: General requirements for machines, instruments and other industrial products and calculation methods for their complex structures as to seismic stability

GOST 30753-2001: Carbon and low-alloy steel butt-weldings fittings. Sharply curved bends type 2D (R=DN). Design

GOST 30852.0-2002: Explosionproof electrical apparatus. Part 0. General requirements

GOST 4666-75: Valves. Marking and distinctive painting

GOST 5542-87: Natural fuel gases for industrial and domestic use

GOST 6357-81: Basic norms of interchangeability pipe cylindrical thread

GOST 6527-68: Female ends with pipe cylindrical thread. Dimensions

GOST 7512-82: Nondestructive testing. Welded joints. Radiography method

GOST 8969-75: Pipe steel connections with cylindrical thread for pipelines P=1,6 МPа. Adapter couplings. Basic dimensions

GOST 9150-2002: Basic norms of interchangeability. Metric screw threads. Profile

GOST 9544-2005: Pipeline gate valves. Classes and rates of gates sealibility

GOST R 12.1.019-2009: Occupational safety standards system. Electrical safety. General requirements and nomenclature of kinds of protection

GOST R 50571.29-2009: Electrical installations of buildings. Part 5-55. Selection and erection of electrical equipment. Other equipment

GOST R 50571.3-2009: Low-voltage electrical installations. Part 4-41. Requirements for safety ensuring. Protection against electric shock

GOST R 52350.14-2006: Electrical apparatus for explosive gas atmospheres. Part 14. Electrical installations in hazardous areas (other than mines)

GOST R 52760-2007: Pipeline valves. Requirements for the marking and distinctive painting

GOST R 53672-2009: Pipeline valves. General safety requirements

GOST R 54808-2011: Pipeline valves. Leakage rates of valves.

GOST R 55724-2013: Non-destructive Testing. Welded Joints. Ultrasonic Methods

The Document is Referenced By:

GOST 34670-2020: Gas distribution systems. Gas reduction points. Basic Provisions

GOST 34715.0-2021: Gas distribution systems. Design, construction and liquidation of natural gas distribution networks. Part 0. General requirements

GOST R 55472-2019: Gas distribution systems. Gas distribution networks of natural gas. Part 0. General

GOST R 58095.0-2018: Gas distribution systems. Requirements for gas consumption networks. Part 0. General

GOST R 58423-2019: Gas pressure regulators for inlet pressure not higher than 10 MPa

SP 282.1325800.2023: Apartment heating systems based on individual gas heat generators. Design and construction rules

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English
Price: $745.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English
Price: $349.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English
Price: $414.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!