GOST 34233.1-2017

ГОСТ 34233.1-2017

Vessels and apparatus. Norms and methods of strength calculation. General requirements

Сосуды и аппараты. Нормы и методы расчета на прочность. Общие требования

Status: Effective - Introduced for the first time. IUS 3-2018

This standard establishes norms and methods for calculating the strength of vessels and apparatus made of carbon and alloyed steels, alloys on iron-nickel base, non-ferrous metals (aluminum, copper, titanium and their alloys) used in chemical, petrochemical, oil refining and other industries conditions of single and multiple static loads under internal overpressure, vacuum or external pressure, under the action of axial and lateral forces and bending moments, inertial loads straps and so forth., and sets the safety factor and stability, allowable stress and strength coefficients welds. Norms and methods of strength calculation are applicable if the properties of materials, requirements for the design, manufacture and control of vessels and apparatus meet the requirements of GOST 34347. If deviations from the geometric shape, inaccuracies or quality, the material characteristics differ from the requirements of normative technical documents, then when calculating for strength, these deviations should be taken into account by adjusting the safety factors and allowable stresses, as well as using other methods of calculation

Настоящий стандарт устанавливает нормы и методы расчета на прочность сосудов и аппаратов из углеродистых и легированных сталей, сплавов на железоникелевой основе, цветных металлов (алюминия, меди, титана и их сплавов), применяемых в химической, нефтехимической, нефтеперерабатывающей и других отраслях промышленности, работающих в условиях однократных и многократных статических нагрузок под внутренним избыточным давлением, вакуумом или наружным давлением, под действием осевых и поперечных усилий и изгибающих моментов, инерционных нагрузок и пр., а также устанавливает значения коэффициентов запаса прочности и устойчивости, допускаемых напряжений и коэффициентов прочности сварных швов. Нормы и методы расчета на прочность применимы, если свойства материалов, требования к конструкции, изготовлению и контролю сосудов и аппаратов отвечают требованиям ГОСТ 34347. Если отклонения от геометрической формы, неточности или качество изготовления, характеристики материала отличаются от требований нормативных технических документов, то при расчете на прочность эти отступления должны быть учтены корректировкой коэффициентов запаса и допускаемых напряжений, а также использованием иных методов расчета

Choose Language: 
Format: Electronic (pdf/doc)

Approved: Federal Agency for Technical Regulation and Metrology, 12/14/2017

SKU: RUSS353578

Price: $178.20




The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 71 Chemical industry »

Construction (Max) » Standards » Other state standards used in construction » 75 Extraction and processing of oil, gas and related production »

Evidence base (TR CU, Technical Regulation of the Customs Union) » 032/2013 TR CU. On safety of overpressure equipment » Regulations and standards (to 032/2013 TR CU) »

Standards for pipe fittings (TPA) » 8. Piping valves (TPA) design » 8.2 Calculations » 8.2.1 Strength calculations »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.13 Testing and control of products of engineering industry » 4.13.1 Machinery, equipment and components for general engineering applications » 4.13.1.9 Equipment for centrifugal and gravity separation of liquid and non-uniform systems »

ISO classifier » 71 CHEMICAL INDUSTRY » 71.120 Equipment for chemical industry » 71.120.01 Equipment for chemical industry as a whole »

National standards » 71 CHEMICAL INDUSTRY » 71.120 Equipment for chemical industry » 71.120.01 Equipment for chemical industry as a whole »

ISO classifier » 75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION » 75.200 Equipment for oil refining, oil products and natural gas » 75.200.01 Transportation and storage in general »

National standards » 75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION » 75.200 Equipment for oil refining, oil products and natural gas » 75.200.01 Transportation and storage in general »

National Standards for KGS (State Standards Classification) » Latest edition » G Machines, equipment and tools » G0 General rules and regulations for engineering » G02 Norms of calculation and design »


The Document References:

GOST 19281-2014: High strength rolled steel. General specification

GOST 25054-81: Forgings made of corrosion-resistant steels and alloys

GOST 34233.10-2017: Vessels and apparatus. Norms and methods of strength calculation. Vessels and apparatus working with hydrogen sulfide media

GOST 34233.11-2017: Vessels and apparatus. Norms and methods of strength calculation. Method of strength calculation of shells and heads according to weld misalignment, angular misalignment and shell nonroundness

GOST 34233.12-2017: Vessels and apparatus. Norms and methods of strength calculation. Requirements for the form of submission of strength calculations performed on a computer

GOST 34233.2-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of cylindrical and conical shells, convex and flat bottoms and covers

GOST 34233.3-2017: Vessels and apparatus. Norms and methods of strength calculation. Strengthening the holes in the shells and bottoms at internal and external pressures. Calculation of the strength of the shells and the bottoms with external static loads on the fitting

GOST 34233.4-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of the strength and tightness of flange connections

GOST 34233.5-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of shells and bottoms from the impact of supporting loads

GOST 34233.6-2017: Vessels and apparatus. Norms and methods of strength calculation. Strength calculation with low-cycle loads

GOST 34233.7-2017: Vessels and apparatus. Norms and methods of strength calculation. Heat exchangers

GOST 34233.8-2017: Vessels and apparatus. Norms and methods of strength calculation. Shirts and apparatus

GOST 34233.9-2017: Vessels and apparatus. Norms and methods of strength calculation. Column type apparatus

GOST 34283-2017: Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads

GOST 34347-2017: Steel welded vessels and apparatus. General technical conditions

GOST 5949-75: Gauged corrosion-resistant, heat-resistant and high-temperature steel shape

GOST 8479-70: Structural carbon and alloy steel forgings

The Document is Referenced By:

GOST 34233.10-2017: Vessels and apparatus. Norms and methods of strength calculation. Vessels and apparatus working with hydrogen sulfide media

GOST 34233.11-2017: Vessels and apparatus. Norms and methods of strength calculation. Method of strength calculation of shells and heads according to weld misalignment, angular misalignment and shell nonroundness

GOST 34233.12-2017: Vessels and apparatus. Norms and methods of strength calculation. Requirements for the form of submission of strength calculations performed on a computer

GOST 34233.2-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of cylindrical and conical shells, convex and flat bottoms and covers

GOST 34233.3-2017: Vessels and apparatus. Norms and methods of strength calculation. Strengthening the holes in the shells and bottoms at internal and external pressures. Calculation of the strength of the shells and the bottoms with external static loads on the fitting

GOST 34233.4-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of the strength and tightness of flange connections

GOST 34233.5-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of shells and bottoms from the impact of supporting loads

GOST 34233.6-2017: Vessels and apparatus. Norms and methods of strength calculation. Strength calculation with low-cycle loads

GOST 34233.7-2017: Vessels and apparatus. Norms and methods of strength calculation. Heat exchangers

GOST 34233.8-2017: Vessels and apparatus. Norms and methods of strength calculation. Shirts and apparatus

GOST 34233.9-2017: Vessels and apparatus. Norms and methods of strength calculation. Column type apparatus

GOST 34283-2017: Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads

GOST 34347-2017: Steel welded vessels and apparatus. General technical conditions

GOST 34473-2018: Pipe fittings. Cranes spherical steel all-welded for water thermal networks. General technical conditions

PNST 305-2018: Rolling stock working on liquefied natural gas. Methods for taking samples and analyzing the content of oils and impurities in the used liquefied natural gas

Decision 18: About the Program for the development (amendment, revision) of interstate standards, the application of which on a voluntary basis ensures compliance with the technical regulations of the Customs Union "On the safety of equipment operating under excessive pressure" (TR TS 032/2013), and interstate standards containing the rules and methods of research (testing) and measurements, including the rules for sampling, necessary for the application and implementation of the requirements of the technical regulations of the Customs Union "О pretensioners equipment operating under excess pressure "(TR CU 032/2013) and of conformity assessment of technical regulation objects

GOST R 58616-2019: Pipe fittings. Regulating fittings for main oil pipelines and oil product pipelines. General specifications

GOST R 58622-2019: The main pipeline transport of oil and oil products. Methodology for assessing the strength, stability and durability of a vertical steel tank

GOST R 58773-2019: Oil and gas industry. Offshore oil and gas facilities. Floating Positioning Systems

GOST R 58819-2020: Pipe fittings for trunk oil pipelines and oil product pipelines. Rules for assessing the technical condition and extension of assigned indicators

Customers Who Viewed This Item Also Viewed:

Electromagnetic compatibility of technical equipment. Immunity of equipment for general lighting purposes to electromagnetic disturbance. Requirements and test methods
Language: English
Price: $218.25
Unified system for design documentation. Exploitative documents
Language: English
Price: $150.48
Еlectromagnetic compatibility of technical equipment. Harmonic current emissions (equipment input current <= 16 A per phase). Limits and test methods
Language: English
Price: $410.31
Еlectromagnetic compatibility of technical equipment. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems. Equipment with rated current <= 16 A and not subject to conditional connection. Limits and test methods
Language: English
Price: $359.87
Pipeline valves. General safety requirements
Language: English
Price: $213.84
Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
Language: English
Price: $714.89
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $108.90
Obosnovanie bezopasnosti oborudovaniya. Rekomendatsii po podgotovke
Language: English
Price: $67.32
Aviation turbine fuels. Determination of lubricity by the ball-on-cylinder lubricity evaluator (BOCLE)
Language: English
Price: $309.43
Aviation turbine fuel. Determination of acidity
Language: English
Price: $218.25
Petroleum products. Determination of color by Saybolt chromometer
Language: English
Price: $218.25
Passenger cars on locomotive traction. Requirements for structural strength and dynamic qualities
Language: English
Price: $595.58
Aviation fuels. Calculating net calorific value
Language: English
Price: $179.45
Aviation fuels. Calculating net calorific value
Language: English
Price: $192.06
Conformity assessment system for the use of nuclear energy. Personnel in the non-destructive and destructive testing of metal. Requirements and qualification procedure Дата введения в действие 15.03.2018
Language: English
Price: $207.90
Security of Financial (banking) Operations. Information Protection of Financial Organizations. Basic Set of Organizational and Technical Measures
Language: English
Price: $843.90
Construction in seismic regions of Ukraine
Language: English
Price: $5,909.85
Aviation turbine fuels and kerosine. Determination of smoke point
Language: English
Price: $270.63
Distillate fuels. Determination of free water and particulate contamination by visual inspection method
Language: English
Price: $165.87
Unified system of corrosion and ageing protection. Paint coatings. Groups of operation conditions
Language: English
Price: $158.40

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!