imgalt

GOST R 58121.1-2018

ГОСТ Р 58121.1-2018

Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 1. General

Пластмассовые трубопроводы для транспортирования газообразного топлива. Полиэтилен (ПЭ). Часть 1. Общие положения

Status: Effective - Introduced for the first time. IUS 8-2018; the date of introduction was postponed from 01/01/2019 to 01/01/2019 (Rosstandart order of November 8, 2018 No. 948); IUS 1-2019

This standard establishes the general characteristics of compositions of polyethylene (PE) used for the manufacture of pipes, fittings intended for the transportation of gaseous fuels. Together with GOST R 58121.2, GOST R 58121.3, this standard is applicable to pipes, fittings made of PE, their connections and connections with other elements made of PE and other materials intended for use under the following conditions: - the maximum working pressure (MOR), determined on the basis of the calculated stress obtained by dividing the minimum long-term strength of the composition (MRS) by the factor of safety C and taking into account the results of tests for the rapid propagation of cracks (BRT), if the value obtained is less than the calculated value by Nove MRS; - temperature of 20 ° С is taken as a base when designing

Настоящий стандарт устанавливает общие характеристики композиций из полиэтилена (ПЭ), применяемых для изготовления труб, фитингов, предназначенных для транспортирования газообразного топлива. Совместно с ГОСТ Р 58121.2, ГОСТ Р 58121.3 настоящий стандарт применим к трубам, фитингам из ПЭ, их соединениям и соединениям с другими элементами из ПЭ и других материалов, предназначенных для применения при следующих условиях: - максимальное рабочее давление (МОР), определенное исходя из расчетного напряжения, полученного путем деления минимальной длительной прочности композиции (MRS) на коэффициент запаса прочности С и с учетом результатов испытаний по быстрому распространению трещин (БРТ), если полученное значение меньше, чем рассчитанное на основе MRS; - температура 20 °С принимается в качестве базовой при проектировании

Choose Language: 
Format: Electronic (pdf/doc)

Approved: Federal Agency for Technical Regulation and Metrology, 5/31/2018

SKU: RUSS354085

Price: $731.00



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 23 Hydraulic and pneumatic systems and components for general use. »

Construction (Max) » Standards » Other state standards used in construction » 83 Rubber, technical rubber, asbestos and plastic industries »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.10 Testing and monitoring products of rubber and plastics industry » 4.10.2 Plastic Products »

ISO classifier » 23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS » 23.040 Pipelines and their components » 23.040.20 Plastic pipes »

National standards » 23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS » 23.040 Pipelines and their components » 23.040.20 Plastic pipes »

ISO classifier » 23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS » 23.040 Pipelines and their components » 23.040.45 Plastic fittings »

National standards » 23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS » 23.040 Pipelines and their components » 23.040.45 Plastic fittings »

ISO classifier » 83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY » 83.140 Rubber and plastic products » 83.140.30 Plastic pipes, fittings not for liquids »

National standards » 83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY » 83.140 Rubber and plastic products » 83.140.30 Plastic pipes, fittings not for liquids »


The Document References:

GOST 11262-2017: Plastics. Tensile test method

GOST 11645-73: Plastics method of determination of melt flow index for thermoplastics

GOST 12423-2013: Plastics. Standard atmospheres for conditioning and testing specimens

GOST 14192-96: Cargo marking

GOST 14870-77: Reagents. Methods for determination of water

GOST 15139-69: Plastics. Methods for the determination of density (mass density)

GOST 16338-85: Low-pressure polyethylene. Specifications

GOST 26277-84: Plastics. Preparation of test specimens by machining

GOST 26311-84: Polyolefins. Method of determination of black content

GOST 26359-84: Polyethylene. Method for determination of volatile matters content

GOST 32794-2014: Polymer composites. Terms and definitions

GOST 33366.1-2015: Plastics. Symbols and abbreviated terms. Part 1. Basic polymers and their special characteristics

GOST 8032-84: Preferred numbers and series of preferred numbers

GOST 9.708-83: Unified system of corrosion and ageing protection. Plastics. Ageing test methods on exposure to natural and artificial climatic factors

GOST ISO 1167-1-2013: Thermoplastics pipes, fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Part 1. General method

GOST ISO 1167-2-2013: Thermoplastics pipes, fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Part 2. Preparation of pipe test pieces

GOST ISO 12162-2017: Thermoplastic materials for pressure pipes and fittings. Classification, designation and safety factor

GOST ISO 4065-2005: Thermoplastics pipes. Universal wall thickness table

GOST R 15.301-2016: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture

GOST R 53652.1-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 3. General requirement

GOST R 53652.3-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 3. Polyolefin pipes

GOST R 54866-2011: Thermoplastics pipes. Determination of the long-term hydrostatic strength on pipe samples by extrapolation method

GOST R 56756-2015: Plastics. Differential scanning calorimetry (DSC). Part 6. Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)

GOST R 58121.2-2018: Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 2. Pipes

GOST R 58121.3-2018: Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 3. Fittings

GOST R ISO 11413-2014: Plastics pipes and fittings. Preparation of test piece assemblies between a polyethylene pipe and an electrofusion fitting

GOST R ISO 11414-2014: Plastics pipes and fittings. Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

GOST R ISO 18553-2013: Polyolefin pipes, fittings and compounds. Method for the assessment of the degree of pigment or carbon black dispersion

GOST R ISO 3126-2007: Plastics piping systems. Plastics components of piping systems. Determination of dimensions

The Document is Referenced By:

GOST R 58121.2-2018: Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 2. Pipes

GOST R 58121.3-2018: Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 3. Fittings

GOST R 59417-2021: Biological safety. Determination of the biogas potential of municipal solid waste landfills with the pumping of biogas from vertical wells and utilization in a flare unit. General specifications

GOST R 59910-2021: Polymeric pipes reinforced with a metal framework, and connecting parts to them. General technical conditions

GOST R 70628.1-2023: Plastic pipelines for water supply, drainage and pressure sewerage. Polyethylene (PE). Part 1. General requirements

GOST R 70628.2-2023: Plastic pipelines for water supply, drainage and pressure sewerage. Polyethylene (PE). Part 2. Pipes

GOST R 70628.3-2023: Plastic pipelines for water supply, drainage and pressure sewerage. Polyethylene (PE). Part 3. Fittings

GOST R 70628.5-2023: Plastic pipelines for water supply, drainage and pressure sewerage. Polyethylene (PE). Part 5. Conformity with the intended use of the system

GOST R 70751-2023: Heat-resistant polymeric pipes for laying power cables with a voltage of 1 to 500 kV. General specifications

Resolution 2425: On approval of the single list of products subject to mandatory certification and the single list of products subject to declaration of conformity, amending the decree of the Government of the Russian Federation of December 31, 2020 N 2467 and repealing certain acts of the Government of the Russian Federation

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English
Price: $745.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English
Price: $349.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English
Price: $414.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!