SP 118.13330.2011
СП 118.13330.2011
|
|
Public buildings and works
Общественные здания и сооружения
These norms and rules apply to the design of new, reconstructed and overhaul public buildings up to 55 m high * with a basement and multi-level parking for cars designed in accordance with SNiP 21-02. The requirements of these standards also apply to public premises built into residential buildings and other facilities that comply with the sanitary and epidemiological requirements for public buildings that are built into these facilities. For public premises built into residential buildings and built-in attached to them, the requirements of SNiP 31-01 should also be considered. Accommodation in public buildings and structures for other purposes is allowed subject to environmental, sanitary and epidemiological and safety requirements corresponding to public buildings. The provisions of these rules should be observed when designing buildings and premises of institutions and enterprises of various forms of ownership and various legal forms. These standards do not apply to the design of seasonal and mobile buildings and public facilities
Настоящие нормы и правила распространяются на проектирование новых, реконструируемых и капитально ремонтируемых общественных зданий высотой до 55 м* с подвальным этажом и многоуровневыми стоянками для автомобилей, проектируемыми по СНиП 21-02. Требования настоящих норм распространяются также на помещения общественного назначения, встроенные в жилые здания и другие объекты, соответствующие санитарно-эпидемиологическим требованиям к общественным зданиям, встраиваемым в эти объекты. Для помещений общественного назначения, встроенных в жилые здания и встроенно-пристроенных к ним, следует учитывать также требования СНиП 31-01. Размещение в общественных зданиях и сооружениях помещений иного назначения допускается при условии соблюдения экологических, санитарно-эпидемиологических и требований по безопасности, соответствующих общественным зданиям. Положения настоящих норм следует соблюдать при проектировании зданий и помещений учреждений и предприятий различных форм собственности и различных организационно-правовых форм. Настоящие нормы не распространяются на проектирование сезонных и мобильных зданий и сооружений общественного назначения
Choose Language:
Format: Electronic (pdf/doc)
SKU: RUSS366421
The Document is Replaced With:
SP 118.13330.2012: Public buildings and facilities
The Document References:
GN 2.2.5.1313-03: Maximum allowable concentrations (MACs) of harmful substances in occupational air
NPB 105-03: Determination of categories of rooms, buildings and external installations on explosion and fire hazard
NPB 110-03: The list of buildings, constructions, rooms and equipment subject to protection by automatic extinguishing units and automatic fire alarm
PB 03-576-03: Regulations of design and safe operation of pressure vessels
PPB 01-03: On Approval Of Fire Safety Standards In The Russian Federation
PUE: Electrical Installation Rules (PUE). Chapter 1.1 General (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.2 Electricity supply and electrical networks (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.7 Grounding and Electrical Safety Precautions (Seven Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.9 Insulation of electrical installations (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.6 Electric Welding Machines (Seven Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.10. Electrolysis Plants and Plating Plants (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.8. Acceptance Test Standards (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.1. Switchgears up to 1 kV AC and up to 1.5 kV DC (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.1. General part (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.2. Electricity supply and electrical networks (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.3. Selection of conductors by heating, economic current density and by corona conditions (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.4. Selection of electrical devices and conductors for short circuit conditions (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.5. Electricity metering (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.6. Electrical Measurements (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.7. Grounding and Electrical Safety Precautions (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.1. Electrical Wiring (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.2. Busducts up to 35 kV (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.3. Cable lines with voltage up to 220 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.4. Overhead power lines with voltage up to 1 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.5. Overhead power lines with voltage above 1 kV (Beginning) (with Amendments and additions) (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.1. Protection of electrical networks with voltage up to 1 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.2. Relay Protection (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.3. Automation and telemechanics (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 3.4. Secondary Circuits (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.2. Switchgears and substations with voltages above 1 kV (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.3. Converter substations and installations (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.4. Battery Units (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.1. Electrical machine rooms (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.2. Generators and Synchronous Compensators (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.3. Electric motors and their switching devices (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.4. Crane Electrical Equipment (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.5. Elevator Electrical Equipment (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 5.6. Condensing Units (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.1. General part (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.1. Electrical equipment of residential, public, administrative and domestic buildings (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.2. Interior lighting (seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.3. Outdoor lighting (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.4. Advertising Lighting (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.5. Lighting fixtures, installation devices (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.2. Electrical installations of entertainment enterprises, clubs and sports facilities (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.3. Electrical Installations in Hazardous Areas (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.4. Electrical Installations in Fire Hazardous Zones (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.5. Electrothermal Plants (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.6. Electric welding machines (sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.7. Peat electrical installations (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.5. Overhead power lines with voltages above 1 kV (End) (Sixth edition)
PUE: Electrical Installation Rules (PUE). Applications
PUE: Electrical Installation Rules (PUE). Chapter 6.6. Lighting devices and wiring devices (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.1. General part (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.2. Interior lighting (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.3. Outdoor Lighting (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.4. Advertising Lighting (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 6.5. Lighting fixtures, installation devices (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.1. Electrical Equipment for Residential and Public Buildings (Sixth Edition)
PUE: Electrical Installation Rules (PUE). Chapter 7.2. Electrical equipment for entertainment enterprises, clubs and sports facilities (Sixth edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.4. Overhead power lines with voltage up to 1 kV (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 2.5. Overhead power lines with voltage above 1 kV (Seventh edition) (with Amendment)
PUE: Electrical Installation Rules (PUE). Chapter 4.1. Switchgears up to 1 kV AC and up to 1.5 kV DC (Seventh Edition)
PUE: Electrical Installation Rules (PUE). Chapter 4.2. Switchgears and substations with voltages above 1 kV (Seventh edition)
PUE: Electrical Installation Rules (PUE). Chapter 1.8. Acceptance test standards (Seventh edition)
RD 78.36.003-2002: Engineering and technical consolidation. Technical means of protection. Requirements and design standards for the protection of facilities from criminal attacks. The guidance.
SanPiN 2.1.2.1188-03: Swimming pools. Hygienic requirements for arrangement, operation and quality of water, quality control
SanPiN 2.1.2.1199-03: Hairdresser's Shops. Sanitation and Disease Control Regulations for Design, Equipment, and Maintenance
SanPiN 2.1.2.1331-03: Hygienic Requirements on the Design, Operation, and Water Quality of Water Parks
SanPiN 2.1.3.1375-03: Hygienic requirements for placement, arrangement, equipment and operation of hospitals, maternity homes and other health facilities
SanPiN 2.1.7.728-99: Soil inhabited localities purification domestic and industrial wastes. Sanitary protection of soil
SanPiN 2.2.1/2.1.1.1076-01: Hygienic requirements for sun effect and solar protection of domestic and public buildings and areas. Sanitary regulations and standards
SanPiN 2.2.1/2.1.1.1278-03: Health requirements for natural, artificial and mixed lighting of residential and public buildings
SanPiN 2.2.2.1332-03: Hygienic Requirements for Organization of Work at Copying and Reproducing Equipment
SanPiN 2.2.2/2.4.1340-03: Hygienic requirements for personal electronic computers and work organization
SanPiN 2.2.4.548-96: Hygienic requirements to occupational microclimate
SanPiN 2.3.6.1079-01: Hygiene and Epidemiology Criteria for Public Catering Establishments and for the Preparation and Circulation By Them of Food Products and Raw Foodstuffs
SanPiN 2.4.1.1249-03: Sanitary andepidemiological requirements for organization, content and operating mode of preschool educational institutions
SanPiN 2.4.2.1178-02: Hygienic requirements to training conditions in educational institutions
SanPiN 2.4.3.1186-03: Sanitary and epidemiological requirements for organization of training process in educational institutions of primary professional education
SanPiN 2.4.4.1204-03: Sanitation and Disease Control Regulations for Design, Maintenance, and Management of the Operation of Suburban Stationary Facilities for Child Recreation and Health Improvement
SN 2.2.4/2.1.8.562-96: Noise exposure in work environment, residential premises, premises of public buildings and in dwellings zones
SN 2.2.4/2.1.8.566-96: Industrial vibration. Vibration in premises of residential and public buildings
SN 2.2.4/2.1.8.583-96: Infrasound on work sites, in residential and public premises, and in housing estate territory
SNiP 2.02.01-83: Footing of buildings and structures
SNiP 2.04.01-85: Domestic water supply and plumbing system
SNiP 2.06.15-85: Inundation & under-flooding. Area protection engineering
SNiP 2.07.01-89: Urban planning. Planning and development of urban and rural areas
SNiP 2.09.04-87: Administrative and accessory buildings
SNiP 21-02-99: Car parking
SNiP 23-01-99: Building climatology
SNiP 23-02-2003: Buildings Heat Insulation
SNiP 23-05-95: Natural and artificial lighting
SNiP 31-01-2003: Multicompartment residential buildings
SNiP 31-03-2001: Production buildings
SNiP 31-05-2003: Public office buildings
SNiP 35-01-2001: Buildings accessibility for disabled population
SNiP 41-01-2003: Heating, Ventilation and Air Conditioning (HVAC)
SNiP 42-01-2002: State committee of Russian Federation for construction and residential-utility complex (GOSSTROY OF Russia)
SNiP II-11-77: Civil defense protective facilities
SNiP II-35-76: Design norms Steam generating units
SO 153-34.21.122-2003: Instruction on lightning protection for buildings, constructions and industrial communications
SP 2.5.1198-03: Sanitary regulations for the organization of passenger transportation by rail
SP 3.13130.2009: Systems of fire protection. System of annunciation and management of human evacuation at fire. Requirements of fire safety
SP 31-108-2002: Refuse ducts for residential and public buildings and structures.
SP 31-110-2003: Design and installation of electrical facilities of residential and public buildings. To replace VSN 59-88
SP 31-112-2004: Gyms and sports facilities, (Parts 1 and 2)
SP 35-101-2001: Designing of buildings and facilities, taking into account accessibility for people with limited mobility. General provisions
SP 35-103-2001: Public buildings and facilities accessible to visitors with limited mobility
SP 41-101-95: Designing heat supply stations (to the SNiP 2.04.07-86)
SP 5.13130.2009: Fire protection systems. Automated fire alarm and fire extinguishing installations. Design norms and regulations
VMR 2.1.3.2365-08: Temporary recommended practice for the placement, arrangement and equipment of centers of high medical technologies
The Document is Referenced By:
SP 30.13330.2012: Domestic water supply and sewerage of buildings.
Customers Who Viewed This Item Also Viewed:
|
Liquid lubricating and plastic materials. Method of test for lubricating properties on four ball machine
Language: English |
Armour clothes. Classification and general technical requirements
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Food products. Methods for detection and quantity determination of coliformes
Language: English |
Natural gas. Methods of calculation of physical properties. Calculation of physical properties on base information on density of standards conditions and nitrogen and carbon dioxide contents
Language: English |
Hotels design
Language: English |
Railroad rails. General specifications
Language: English |
Potassium chloride
Language: English |
Controllers acting without
Language: English |
|
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.