The supporting structures of the elements of nuclear plants with water-cooled power reactors. General technical requirements
Опорные конструкции элементов атомных станций с водо-водяными энергетическими реакторами. Общие технические требования
Status: Effective - Introduced for the first time
The document establishes the requirements for the purpose, design (construction), materials, manufacturing, installation, testing, operation (including operational control), repair, extension of the service life and decommissioning of supporting structures of elements of power units of WWER nuclear power plants. The document is intended for organizations involved in the design (construction), construction, operation, extension of operation and decommissioning of nuclear power units with VVER, as well as for organizations involved in the above works
В документе установлены требования к назначению, проектированию (конструированию), материалам, изготовлению, монтажу, испытаниям, эксплуатации (включая эксплуатационный контроль), ремонту, продлению срока службы и выводу из эксплуатации опорных конструкций элементов энергоблоков АЭС с ВВЭР. Документ предназначен для организаций, осуществляющих проектирование (конструирование), сооружение, эксплуатацию, продление эксплуатации и вывод из эксплуатации энергоблоков АЭС с ВВЭР, а также для организаций, привлекаемых к перечисленным работам
Format: Electronic (pdf/doc)
Approved: Rosenergoatom Concern OJSC,
The Product is Contained in the Following Classifiers:
Construction (Max) »
Sectoral and departmental regulatory and methodological documents »
Design and construction of energy facilities »
SECTION IV. INDUSTRIAL SAFETY »
III Nuclear and radiation safety »
3 Atomic stations »
ISO classifier »
27 ENERGY AND HEATING TECHNOLOGY »
27.120 Nuclear power engineering »
27.120.99 Nuclear energy, other aspects »
The Document References:
GOST 10157-79: Gaseous and liquid argon. Specifications
GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications
GOST 10706-76: Electrically welded steel line-weld tubes. Technical requirements
GOST 11371-78: Washers. Specifications
GOST 12344-2003: Alloyed and high-alloyed steels. Methods for determination of carbon
GOST 12352-81: Steels alloyed and highalloyed. Methods for the determination of nickel
GOST 12353-78: Alloyed and high-alloyed steels. Methods of cobalt determination
GOST 12354-81: Steels alloyed and highalloyed. Methods for the determination of molybdenum
GOST 12356-81: Steels alloyed and highalloyed. Methods of the determination of titanium
GOST 12357-84: Steels alloyed and highalloyed. Methods for the, determination of aluminium
GOST 12361-2002: Alloyed and highalloyed steels. Methods for determination of niobium
GOST 12365-84: Steels alloyed and highalloyed. Methods for the determination of zirconium
GOST 13764-86: Cylindrical helical compression (tension) springs made of round steel. Classification
GOST 14637-89: Thick sheet rolled stock of normal quality carbon steel
GOST 14771-76: Gas-shielded arc welding. Welded joints. Main types, design elements and dimensions
GOST 14959-79: Spring carbon and alloy steel bars. Specifications
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 1577-93: Plate and broadband roll stock of construction fine steel.
GOST 16523-97: Rolled sheets from quality and ordinary carbon steel for general purposes. Specifications
GOST 1759.0-87: Bolts, screws, studs and nuts. Specifications.
GOST 1759.4-87: Bolts, screws and studs. Mechanical properties and test methods
GOST 1759.5-87: Nuts. Mechanical properties and test methods
GOST 1778-70: Steel. Metallographic methods for the determination of non-metallic inclusions
GOST 18300-87: Technical rectified ethyl alcohol. Specifications
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 19903-74: Hot-rolled steel sheets. Dimensions
GOST 19904-74: Cold-rolled sheet. Range
GOST 20072-74: Heat-resistant steel
GOST 20700-75: Bolts, studs, nuts and washers for flanged and anchor connections, corks and yokes with medium temperature from 0 to 650 °C. Specifications
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 2246-70: Welding steel wire. Specifications
GOST 22536.0-87: Carbon steel and unalloyed cast iron. General requirements for methods of analysis
GOST 22536.1-88: Carbon steel and unalloyed cast iron. Methods for determination of general carbon and graphite
GOST 22536.5-87: Carbon steel and unalloyed cast iron. Methods for determination of manganese
GOST 22536.7-88: Carbon steel and unalloyed cast iron. Methods for determination of chromium
GOST 23304-78: Bolts, studs, nuts and washers for flanged connections for atomic power plants. Technical requirements. Acceptance. Test methods. Marking, packing, transportation and storage
GOST 24030-80: Seamless pipes from corrosion-resistant steel for power plant industry
GOST 25.506-85: Design, calculation and strength testing. Methods of mechanical testing of metals. Determination of fracture toughness characteristics under the static loading
GOST 25054-81: Forgings made of corrosion-resistant steels and alloys
GOST 2590-2006: Round hot-rolled steel bars. Dimensions
GOST 2601-84: Welding of metals. Terms and definitions of basic concepts
GOST 27809-95: Cast iron and steel. Methods of spectrographic analysis
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 380-2005: Common quality carbon steel. Grades
GOST 4543-71: Structural alloyed steel
GOST 4986-79: Cold-rolled band from corrosion-resistant and heat-resistant steel
GOST 5264-80: Manual are welding. Welding joints. Main types, design elements and dimensions
GOST 535-2005: Common quality carbon steel bar and shaped sections. General specifications
GOST 5520-79: Carbon, low-alloy and alloy sheet steel for boilers and pressure vessels. Specifications
GOST 5582-75: Corrosion-resistant, heat-proof, and heat-resistant thin-sheet rolled stock
GOST 5583-78: Industrial and medical gaseous oxygen
GOST 5632-72: High-alloy steels and corrosion-proof, heat-resisting and heat treated alloys. Grades
GOST 5781-82: Hot-rolled steel for reinforcement of ferroconcrete structures. Specifications
GOST 5949-75: Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
GOST 6996-66: Welded joints. Methods of mechanical properties determination
GOST 7350-77: Plate, corrosion-resistant, heat-resistant, and high-temperature steel
GOST 8.002-86: State system for ensuring the uniformity of measurements. State supervision and department control of measuring instruments. Basic regulations
GOST 8.376-80: State system for ensuring the uniformity of measurements. Universal instruments for measuring solvents. Methods and means of verification
GOST 8050-85: Carbon dioxide,
GOST 8240-97: Hot-rolled steel channels. Assortment
GOST 8479-70: Structural carbon and alloy steel forgings
GOST 8509-93: Hot-rolled steel equal-leg angles. Dimensions
GOST 8510-86: Hot-rolled steel unequal-leg angles. Dimensions
GOST 9087-81: Welding melted fluxes
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST 9940-81: Seamless hot-deformed tubes made from corrosion-resistant steel
GOST 9941-81: Seamless cold- and warm-deformed tubes made from corrosion-resistant steel
OST 108.030.113-87: Carbon and alloy steel forgings for thermal and nuclear power stations equipment and pipelines. Technical specifications.
OST 108.109.01-92: Basic part billets made of corrosion-resistant steels of austenitic class. Technical conditions.
OST 153-34.0-972-99A: Assembly units and support parts for station pipelines of nuclear power plants Py <= 1.6 MPa (16 kgf/cm2). Support welded sliding, directing and motionless. Design and dimensions
OST 153-34.0-972-99А: Assembling units and support station pipeline details of nuclear power plants. Nominal pressure is no more than 1,6 MPa. The support is welded and sliding, guide rail and fixed. Design and dimensions.
OST 153-34.0-973-99A: Assembly units and parts of the supports of the station pipelines of nuclear power plants Py <= 2.5 MPa (25 kgf/cm2). Welded sliding bearing, guide and fixed. Design and dimensions
OST 153-34.0-973-99А: Assembling units and support station pipeline details of nuclear power plants. Nominal pressure is no more than 2,5 MPa. Sliding support is welded guide rail and the fixed. Design and dimensions.
OST 153-34.0-974-99A: Assembly units and support parts for station pipelines of nuclear power plants Py <= 4.0 MPa (40 kgf/cm2). Support clamp sliding, guide and fixed. Design and dimensions
OST 24.125.151-01: Fixed support for thermal and nuclear power plants piping. Design and dimensions.
OST 24.125.154-01: Slide bearings for pipelines thermal and nuclear power plants. Design and dimensions.
OST 24.125.156-01: Welded sliding guide supports for piping thermal and nuclear power plants. Design and dimensions.
OST 3-1686-90: Billets made of structural steel for engineering. General Specifications.
OST 34-10-735-93: Clip for horizontal pipelines. Design and dimensions.
OST 34-10-736-93: Clip for vertical pipelines. Design and dimensions.
OST 95-29-72: Billets made of corrosion-resistant steels of 12Х18Н9Т, 12Х18Н10Т, 08Х18Н10Т, 10Х17Н13М2Т, 12Х18Н12Т and 03Х21Н32М3Б types.
PB 03-440-02: Attestation rules for nondestructive inspection personnel
PNAE G-01-011-97: General Safety Regulations for nuclear thermal power plants (SSB 88/97). Also known as NP-001-97.
PNAE G-7-003-87: Certification Requirements for Welders of Equipment and Piping for Nuclear Power Plants
PNAE G-7-008-89: Regulations for design and safe operation of equipment and piping of atomic power plants
PNAE G-7-009-89: Equipment and pipelines of nuclear power installations. Welding and overlaying, general provisions
PNAE G-7-010-89: Equipment and pipelines of nuclear energy facilities. Welded joints and beads. Testing rules
PNAE G-7-015-89: Uniform methods of inspection of main materials (semi-finished products), welded joints and building-up of the equipment and piping of nuclear power units. Magnetic particle inspection
PNAE G-7-016-89: Standardized methods of control of basic materials (semifinished products), welded joints and cladding of equipment and of pipelines of NPP. Visual and a measuring control
PNAE G-7-017-89: Unified technique of inspection of base materials (semifinished products), welded joints and deposits of equipment and pipelines of atomic power plants. Ultrasonic inspection
PNAE G-7-018-89: Safety guidelines. Standardized methods of control of basic materials (semi-finished products), welded joints and surfacing of NPP equipment and piping. Dye penetrant inspection
PNAE G-7-032-91: Uniform control methods for basic materials (semi-finished materials), welded joints and weldings on of equipment and pipelines of nuclear power plants. Ultrasonic testing. Part IV. Examination of welded joints of austenitic steels
PNAJe G-7-002-86: Standards for calculating the strength of equipment and pipelines of nuclear power plants
RD 3-3-85: Model provision of procedure examination rules, regulations and safety instructions in the nuclear industry managing directors and professionals.
SP 1009-73: Sanitary regulations for welding, weld deposition and metal cutting
TU 13.03-011-00212179-2003: Spiral-welded electric-welded pipes made of carbon steel 20 for pipelines of nuclear power plants. Technical conditions
TU 14-3-190-82: Seamless steel pipes for boiler plants and pipelines
TU 14-3R-197-2001: Seamless pipes made of corrosion-resistant steel with high surface quality. Technical conditions
TU 95.349-2000: Longitudinal electric-welded pipes from steel grades 08X18H10T, 12X18H10T for atomic electric and thermal stations. Technical specifications
The Document is Referenced By:
I 1.2.1.02.019.1121-2016: Determination of mechanical properties of metal of equipment of nuclear power plants by means of non-reference technique in terms of hardness characteristics. Instructions
Customers Who Viewed This Item Also Viewed:
Occupational safety standards system Electric welding works. Safety requirements
Steel and alloys. Methods for detection and determination of grain size
Involute toothed (splined) joints
Gas-consuming thermal units. Industrial gas burners. Limiting concentration rates of NOx in combustion products
Horns and signal whistles. General specifications
Steel. Microstructure standards
Steel. Metallographic methods for the determination of non-metallic inclusions
Textiles and articles. Method for the determination of air permeability
Containers for blood and its components. Requirements for chemical and biological safety and methods of testing
Construction and rolling stock clearance diagrams
Automobile roads of general use. Traffic load models, application of the load models
Medical devices. Biological evaluation of medical devices. Part 12. Sample preparation and reference materials
Medical devices. Safety requirements. Methods of sanitation-chemical and toxicological tests
Feedstuffs, compound feeds, feed raw materials. Determination of mass fraction of choline chloride by capillary electrophoresis
Distilled water. Specifications
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.