GOST R 55473-2019
ГОСТ Р 55473-2019
|
|
Gas distribution systems. Gas distribution networks of natural gas. Part 1. Polyethylene gas pipelines
Системы газораспределительные. Сети газораспределения природного газа. Часть 1. Полиэтиленовые газопроводы
Status: The document is enacted from 01.09.2019. Registration information 121-st dated 04/04/2019 (Rosstandart official website) 09/01/2019
The provisions of this standard apply to the design, construction, reconstruction and operation of gas pipelines from polyethylene pipes of gas distribution networks with a maximum working pressure of not more than 1.2 MPa, inclusive, at pipe wall temperatures from minus 20 ° C to 40 ° C, transporting natural gas in accordance with GOST 5542 .
Положения настоящего стандарта распространяются на проектирование, строительство, реконструкцию и эксплуатацию газопроводов из полиэтиленовых труб сетей газораспределения с максимальным рабочим давлением не более 1,2 МПа включительно, при температуре стенки трубы от минус 20 °C до 40 °C, транспортирующих природный газ по ГОСТ 5542.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
4/4/2019
SKU: RUSS373876
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
23 Hydraulic and pneumatic systems and components for general use. »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.01 Pipelines and their components in general »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.01 Pipelines and their components in general »
As a Replacement Of:
GOST R 55473-2013: Gas distribution systems. Requirements for gas distribution networks. Part 1. Polyethylene gas pipelines
The Document References:
Code 190-FZ: Town Planning Code of the Russian Federation
Federal Law 184-FZ: About technical regulation
Federal Law 7-FZ: Environmental Protection
GOST 10198-91: Wooden boxes for weights of mass over 200 up to 20000 kg. General specifications
GOST 12.2.063-2015: Pipeline valves. General safety requirements
GOST 13841-79: Corrugated board boxes for chemical products. Specifications
GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage
GOST 17811-78: Polyethylene bags for chemical products. Specifications
GOST 18599-2001: Polyethylene pressure pipes. Specifications
GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements
GOST 22235-2010: Freight cars for 1520 mm gauge main line railways. General requirements for safety in loading-unloading and shunting operations
GOST 2226-2013: Bags made of paper and composite materials. General specifications
GOST 24105-80: Plastics products. Terms and definitions of defects
GOST 24297-2013: Verification of purchased product. Organization and methods of control
GOST 26653-2015: Preparation of general cargoes for transportation. General requirements
GOST 26663-85: Transport packets. Formation by packaging means. General technical requirements
GOST 2930-62: Measuring instruments. Characters and signs
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 30090-93: Sacks and fabric for sacks
GOST 5542-2014: Natural fuel gases for commercial and domestic use. Specifications
GOST 5959-80: Uncollapsable wooden sheet material boxes for weights to 200 kg mass. General specifications
GOST 9.602-2016: Unified system of corrosion and ageing protection. Underground constructions. General requirements for corrosion protection
GOST ISO 161-1-2004: Thermoplastics pipes for the conveyance of fluids. Nominal outside diameters and nominal pressures. Metric series
GOST R 53865-2010: Gas distribution systems. Terms and definitions
GOST R 54983-2012: Gas distribution systems. Natural gas distribution networks. General requirements for operation. Operational documentation
GOST R 55276-2012: Plastics pipes and fittings. Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems
GOST R 55472-2019: Gas distribution systems. Gas distribution networks of natural gas. Part 0. General
GOST R 55474-2013: Gas distribution systems. Requirements for gas distribution networks. Part 2. Steel gas pipelines
GOST R 56290-2014: Gas distribution systems. Requirements to gas distribution networks. Part 3. Renovation
GOST R 58121.2-2018: Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 2. Pipes
GOST R 58121.3-2018: Plastic pipings for the supply of gaseous fuels. Polyethylene (PE). Part 3. Fittings
GOST R ISO 12176-1-2011: Plastics pipes and fittings. Equipment for fusion jointing polyethylene systems. Part 1. Butt fusion
GOST R ISO 12176-2-2011: Plastics pipes and fittings. Equipment for fusion jointing polyethylene systems. Part 2. Electrofusion
GOST R ISO 3126-2007: Plastics piping systems. Plastics components of piping systems. Determination of dimensions
SP 11-110-99: Code of standards on design and construction Designer’s supervision over construction of building and facilities
SP 246.1325800.2016: Code practice. Regulation on the supervision of authors for construction of buildings and structures
SP 42-103-2003: Design and construction of polyethilene gas pipelines and renovation of underground gas pipelines
SP 45.13330.2017: Earthworks, grounds and footings
SP 48.13330.2011: Organization of construction
SP 62.13330.2011: Gas distribution systems
The Document is Referenced By:
GOST R 55472-2019: Gas distribution systems. Gas distribution networks of natural gas. Part 0. General
Customers Who Viewed This Item Also Viewed:
|
Liquid lubricating and plastic materials. Method of test for lubricating properties on four ball machine
Language: English |
Armour clothes. Classification and general technical requirements
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Food products. Methods for detection and quantity determination of coliformes
Language: English |
Natural gas. Methods of calculation of physical properties. Calculation of physical properties on base information on density of standards conditions and nitrogen and carbon dioxide contents
Language: English |
Hotels design
Language: English |
Railroad rails. General specifications
Language: English |
Potassium chloride
Language: English |
Controllers acting without
Language: English |
|
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.