GOST R 58616-2019
ГОСТ Р 58616-2019
Pipe fittings. Regulating fittings for main oil pipelines and oil product pipelines. General specifications
Арматура трубопроводная. Арматура регулирующая для магистральных нефтепроводов и нефтепродуктопроводов. Общие технические условия
Status: The document is enacted from 08/01/2020. Registration information 1075-st dated 11/01/2019 (Rosstandart official website) 08/01/2020
The standard applies to regulating and stop-regulating pipe fittings for main oil pipelines and oil product pipelines with a nominal diameter of DN 50 to DN 800 for a nominal pressure of PN 1.6 to PN 12.5 MPa (16 to 125 bar or kgf / cm2).
Стандарт распространяется на регулирующую и запорно-регулирующую трубопроводную арматуру для магистральных нефтепроводов и нефтепродуктопроводов номинальным диаметром от DN 50 до DN 800 на номинальное давление от PN 1,6 до PN 12,5 МПа (от 16 до 125 бар или кгс/см2).
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
The Product is Contained in the Following Classifiers:
SECTION III. LABOR PROTECTION AND SAFETY »
III Occupational safety requirements for production equipment and processes »
2 Safety requirements for certain types of work »
2.2 Operation of production machines and equipment »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.13 Testing and control of products of engineering industry »
4.13.1 Machinery, equipment and components for general engineering applications »
220.127.116.11 Components and assembly units for general engineering applications »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.060 Pipe fittings »
23.060.40 Control valves »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.060 Pipeline valves »
23.060.40 Control valves »
The Document References:
Federal Law 162-FZ: About standardization in the Russian Federation
GOST 1012-2013: Aviation petrols. Specifications
GOST 10227-2013: Jet fuels. Specifications
GOST 10433-75: Fuel oil for gas-turbine plants. Specifications
GOST 10585-2013: Petroleum fuel. Mazut. Specifications
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.007-76: Noxious substances. Classification and general safety requirements
GOST 12.1.010-76: Explosion safety. General requirements
GOST 12.2.063-2015: Pipeline valves. General safety requirements
GOST 12.3.009-76: Occupational safety standards system. Loading and unloading works General safety requirements
GOST 12971-67: Rectangular plates for machines and devices. Dimensions
GOST 14192-96: Cargo marking
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 16504-81: The state system of testing products. Product test and quality inspection. General terms and definitions
GOST 1667-68: Motor fuel for medium- and low-speed diesel engines
GOST 18322-2016: Maintenance and repair system of engineering. Terms and definitions
GOST 19281-2014: High strength rolled steel. General specification
GOST 21752-76: Man-machine system Control hand wheels and steering wheels General ergonomic requirements
GOST 23170-78: Packing for products of engineering industry. General requirements.
GOST 24297-2013: Verification of purchased product. Organization and methods of control
GOST 24856-2014: Pipeline valves. Terms and definitions
GOST 25573-82: Freight handling rope slings for construction
GOST 27.003-2016: Reliability in technology. Composition and general rules for setting reliability requirements
GOST 28338-89: Nominal bores (nominal sizes)
GOST 28908-91: Ball valves and disk gate valves. End-to-end (face-to-face) dimensions
GOST 305-2013: Diesel fuel. Specifications
GOST 30546.1-98: General requirements for machines, instruments and other industrial products and calculation methods for their complex structures as to seismic stability
GOST 30631-99: General requirements for machines, instruments and other industrial products as to environment mechanical stability
GOST 30852.11-2002: Explosionproof electrical apparatus. Part 12. Classification of mixtures of gases or vapours with air according to their maximum experimental safe gaps and minimum igniting currents
GOST 30852.5-2002: Explosionprotected electrical apparatus. Part 4. Method of test for ignition temperature
GOST 30852.9-2002: Electrical apparatus for explosive gas atmospheres. Part 10. Classification of hazardous areas
GOST 31378-2009: Oil. General specifications.
GOST 33257-2015: Pipeline valves. Methods of control and testing
GOST 33258-2015: Pipeline valves. Surfacing and quality control of surfaced surfaces. Technical requirements
GOST 33259-2015: Flanges for valves, fittings and pipelines for pressure to PN 250. Design, dimensions and general technical requirements
GOST 33260-2015: Pipeline valves. Мetals used in pipeline valves production. Basic requirements for choice of materials
GOST 33272-2015: System of product development and launching into manufacture. Procedure of establishment and extension of the appointed resource, service life and period of storage. Basic provisions
GOST 33857-2016: Pipe fittings. Welding and quality control of welded joints. Technical requirements
GOST 34233.1-2017: Vessels and apparatus. Norms and methods of strength calculation. General requirements
GOST 34233.2-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of cylindrical and conical shells, convex and flat bottoms and covers
GOST 34233.3-2017: Vessels and apparatus. Norms and methods of strength calculation. Strengthening the holes in the shells and bottoms at internal and external pressures. Calculation of the strength of the shells and the bottoms with external static loads on the fitting
GOST 34233.4-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of the strength and tightness of flange connections
GOST 34233.5-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of shells and bottoms from the impact of supporting loads
GOST 34233.6-2017: Vessels and apparatus. Norms and methods of strength calculation. Strength calculation with low-cycle loads
GOST 34437-2018: Pipe fittings. Methods of experimental determination of hydraulic and cavitation characteristics
GOST 4666-2015: Pipeline accessories. Requirements for marking
GOST 9.014-78: Unified system of corrosion and ageing protection. Temporary corrosion protection of products. General requirements
GOST 9.301-86: Unified system of corrosion and ageing protection. Metal and non-metal inorganic coatings. General requirements
GOST 9.302-88: Unified system of corrosion and ageing protection. Metal and non-metal inorganic coatings. Control methods
GOST 9450-76: Measurements microhardness by diamond instruments indentation
GOST 9544-2015: Pipeline valves. Leakage rates of valves
GOST R 15.301-2016: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture
GOST R 27.301-2011: Dependability in technics. Dependability management. Analysis techniques for reliability. General principles
GOST R 27.403-2009: Dependability in technics. Compliance tests plans for reliability
GOST R 51105-97: Gasoline for combustion engines. Unleaded gasoline. Specifications
GOST R 51164-98: Steel pipe mains. General requirements for corrosion protection
GOST R 51866-2002: Automotive fuels. Unleaded petrol. Specifications
GOST R 52050-2006: Aviation turbine fuel Jet A-1. Specifications
GOST R 52368-2005: Diesel fuel EVRO. Specifications
GOST R 52376-2005: Heat-resistant spiral-wound gaskets. Types. Main dimensions
GOST R 53561-2009: Pipelines valves. Jackets of oval, octagonal section, lens steel for valves flanges. Design, dimension and general technical requirements
GOST R 53674-2009: Pipeline valves. Nomenclature of characteristics. Check-lists for design and order
GOST R ISO 6507-1-2007: Metals and alloys. Vickers hardness test. Part 1. Test method
PB 03-273-99: Rules for qualification test of welders and welding production specialists
PB 03-372-00: Non-destructive test laboratory certification rules and main requirements.
PB 03-440-02: Attestation rules for nondestructive inspection personnel
RD 03-495-02: Procedures for the qualification test of welders and welding work specialists
RD 03-613-03: Procedures of use of welding materials during fabrication, installation, repair and modernization of technical systems for hazardous production facilities
RD 03-614-03: Order of welding equipment application at engineering devices production, installation, repair and reconstruction for unsafe industrial objects.
RD 03-615-03: Order of welding technologies application at engineering devices production, installation, repair and reconstruction for unsafe industrial objects.
RD 10-33-93: Slings for loading and general purposes. Requirements for arrangement and safe operation.
TR EAEU 045/2017: Technical regulations of the Eurasian Economic Union "On the safety of oil prepared for transportation and (or) use"
Customers Who Viewed This Item Also Viewed:
Ball valves and disk gate valves. End-to-end (face-to-face) dimensions
Safety valves of stream and hot-water boilers. Technical requirements
Industrial gas burners. General technical requirements
Petroleum and natural gas industries. Shell-and-tube heat eхchangers. Technical requirements
Straight and diamond knurl. Form and basic dimensions
Industrial gas burners. Test methods
Ball, lifting-plug and cylindrical cocks for nominal pressure at most PN 250. General specifications
Unified system for design documentation. Stages of designing
White sugar. Specifications
Pipeline valves. Methods of control and testing
Stainless steels and corrosion resisting, heat-resisting and creep resisting alloys. Grades
Pipeline valves. Leakage rates of valves
Graphite electrodes and nipples. Specifications
Welded steel pipes for gas and oil pipelines. Technical specifications
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.