ODM 218.2.076-2019
ОДМ 218.2.076-2019
|
|
Recommendations on the use of composite structures for areas with extreme temperature conditions (below minus 40 degrees Celsius and above plus 40 degrees Celsius)
Рекомендации по применению конструкций из композитных материалов для районов с экстремальными температурными условиями (ниже минус 40 градусов Цельсия и выше плюс 40 градусов Цельсия)
Status: Effective - Introduced for the first time
The industry road guidance document sets out recommendations for the design, manufacture and repair of structures of bridge structures and pedestrian bridges made of polymer composite materials, which are located in areas with extreme temperature conditions (below -40 degrees Celsius and above +40 degrees Celsius). The lower and upper limits of extreme temperature conditions are -60 degrees Celsius and +60 degrees Celsius, due to the fact that the vast majority of the technical conditions of all manufactured and used composite structural materials (except for special carbon fiber) regulate the preservation of their physicochemical properties and performance at these temperature boundaries.
Отраслевой дорожный методический документ устанавливает рекомендации на проектирование, изготовление и ремонт конструкций мостовых сооружений и пешеходных мостов из полимерных композиционных материалов, которые расположены в областях с экстремальными температурными условиями (ниже -40 градусов Цельсия и выше +40 градусов Цельсия). Нижней и верхней границами экстремальных температурных условий являются -60 градусов Цельсия и +60 градусов Цельсия, ввиду того, что абсолютное большинство технических условий всех изготавливаемых и применяемых композиционных конструктивных материалов (кроме специальных углепластиковых) регламентирует сохранение их физико-химических свойств и работоспособность в этих температурных границах.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Highway Agency,
11/6/2019
SKU: RUSS377566
National keywords: безопасность, испытания, требования, контроль, конструктивные элементы, метод конечных элементов, пешеходные мосты, несущие конструкции, полимерные композиты, вакуумная инфузия, ламинат, метод предельных состояний.;
The Product is Contained in the Following Classifiers:
Highways (Max) »
Design, construction, repair and maintenance of roads »
1. General issues of design and construction (reconstruction) of roads »
Highways (Max) »
Design, construction, repair and maintenance of roads »
14. Security and traffic management. Arrangement and operation of roads »
14.1 General documents »
Construction (Max) »
Regulations »
Sectoral and departmental regulatory and methodological documents »
Design and construction of roads »
The Document References:
GOST 5264-80: Manual arc welding. Welding joints. Main types, design elements and dimensions
GOST 10060-2012: Concretes. Methods for the determination of frost-resistance
GOST 10180-2012: Concretes. Methods for strength determination using reference specimens
GOST 11262-2017: Plastics. Tensile test method
GOST 11371-78: Washers. Specifications
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.044-2018: Occupational safety standards system. Fire and explosion hazard of substances and materials. Nomenclature of indices and methods of their determination
GOST 13015-2012: Concrete and reinforced concrete products for construction. General technical requirements. Rules for acceptance, marking, transportation and storage
GOST 13087-2018: Concrete Abrasion Determination Methods
GOST 15139-69: Plastics. Methods for the determination of density (mass density)
GOST 15173-70: Plastics. Method for determination of mean coefficient of linear thermal expansion
GOST 16782-92: Plastics. Determination of the brittleness temperature by impact
GOST 18105-2010: Concretes. Rules of control and norm of an assessment of quality.
GOST 18197-82: Method of test for tensile creep of plastics
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 19903-2015: Hot-rolled sheet. Range
GOST 19904-90: Cold-rolled steel sheets. Dimensions
GOST 2246-70: Welding steel wire. Specifications
GOST 23630.2-79: Plastics. Method for the determination of thermal conductivity.
GOST 24297-2013: Verification of purchased product. Organization and methods of control
GOST 25.601-80: Design calculation and strength testing. Methods of mechanical testing of polymeric composite materials. Test for tensile properties on plane specimens at normal, elevated and law temperatures
GOST 25.602-80: Design calculation and strength testing. Methods of mechanical testing of polymeric composite materials. Test for compression properties at normal, elevated and low temperatures
GOST 25.604-82: Design calculation and strength testing. Methods of mechanical testing of polymeric composite materials. Test for bending properties at normal, elevated and low temperatures
GOST 26433.1-89: System of ensuring geometrical parameters accuracy in construction. Rules of measurement. Prefabricated elements
GOST 26877-2008: Metal products. Methods of measuring form variations
GOST 27017-86: Fasteners. Terms and definitions
GOST 27751-2014: Reliability for constructions and foundations. General principles
GOST 28840-90: Machines for tension, compression and bending tests of materials
GOST 30244-94: Building materials. Methods for combustibility test
GOST 30247.0-94: Elements of building constructions. Fire-resistance test methods. General requirements
GOST 30247.1-94: Elements of building constructions. Fire-resistance test methods. Load bearing and separating constructions
GOST 30402-96: Building materials Ignitability Test Meth
GOST 4648-71: Plastics. Method of static bending test
GOST 4650-80: Plastics. Methods for the determination of water absorption
GOST 4651-82: Plastics. Compression test method
GOST 535-2005: Common quality carbon steel bar and shaped sections. General specifications
GOST 5582-75: Corrosion-resistant, heat-proof, and heat-resistant thin-sheet rolled stock
GOST 5632-72: High-alloy steels and corrosion-proof, heat-resisting and heat treated alloys. Grades
GOST 5949-2018: Stainless corrosion resisting, heat-resisting and creep resisting steel and alloy on iron-nickel-based products. Specifications
GOST 6958-78: Enlarged washers. Product grades A and C. Specifications
GOST 7350-77: Plate, corrosion-resistant, heat-resistant, and high-temperature steel
GOST 8829-2018: Prefabricated reinforced concrete and concrete products. Load test methods. Rules for evaluating strength, stiffness and crack resistance
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST R 50597-2017: Automobile roads and streets. The requirements to the level of maintenance satisfied the traffic safety. Methods of testing
GOST R 52289-2004: Traffic control devices. Rules of application of traffic signs, markings, traffic lights, guardrails and delineators
Guidelines: The introduction of digital solutions in the urban planning system based on the smart city approach
Manual: Manual for impulse and low consumption fire extinguishing systems
MDS 81-35.2004: Methodology
to determine the cost of construction products in the Russian Federation
MGSN 5.02-99: Design of Urban Bridge Structures
NPB 244-97: Building materials. decorative-finishing and facing materials. Materials for cover of floor. roofing, hydro- and heat-insulating materials. parameters of fire danger
ODM 218.5.006-2008: Guidelines for the use of environmentally friendly anti-icing materials and technologies in the maintenance of bridge structures
Order 402: Classification of works on overhaul, repair and maintenance of highways
Order 402: On approval of the form and procedure for providing extracts from the state consolidated register of issued, suspended and canceled licenses for the production and circulation of ethyl alcohol, alcoholic and alcohol-containing products
SP 43.13330.2012: Structures for industrial installations
SP 79.13330.2012: Bridges and culverts. Rules of examination and test
|
Customers Who Viewed This Item Also Viewed:
 |
Controllers acting without
Language: English |
Building materials. Methods for combustibility test
Language: English |
Building materials spread flame test method
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Clear sheet glass. Specifications
Language: English |
Natural gas. Methods of calculation of physical properties. Calculation of physical properties on base information on density of standards conditions and nitrogen and carbon dioxide contents
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
