GOST 17066-80
ГОСТ 17066-80
|
|
Low-alloyed structural steel sheets and strips in coils. Marks and technical requirements
Прокат тонколистовой из конструкционной низколегированной стали. Технические условия
Status: Not effective - Superseded. IUS 4-1996
This standard applies to hot-rolled and cold-rolled sheet metal from low-alloy structural steel with a thickness of 0.5 to 3.9 mm, a minimum width of 500 mm, produced in rolls and sheets. The technical level indicators established by this standard are provided for the first category of quality. 1. Stamps 2. Assortment 3. Technical requirements 4. Acceptance rules 5. Test methods 6. Packaging, labeling, transportation and storage
Настоящий стандарт распространяется на горячекатаный и холоднокатаный листовой прокат из конструкционной низколегированной стали толщиной от 0,5 до 3,9 мм, шириной не менее 500 мм, изготовляемый в рулонах и листах. Показатели технического уровня, установленные настоящим стандартом, предусмотрены для первой категории качества. 1. Марки 2. Сортамент 3. Технические требования 4. Правила приемки 5. Методы испытаний 6. Упаковка, маркировка, транспортирование и хранение
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
3/27/1980
SKU: RUSS51047
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.12 Testing and control of products of metallurgical industry »
4.12.4 Iron and steel products »
ISO classifier »
77 METALLURGY »
77.140 Iron and steel products »
77.140.50 Steel sheet products and semi-finished products »
National standards »
77 METALLURGY »
77.140 Iron and steel products »
77.140.50 Steel sheet products and semi-finished products »
National Standards for KGS (State Standards Classification) »
Latest edition »
V Metals and metal products »
V2 Carbon steel of ordinary quality (ordinary stock) »
V23 Sheets and Stripes »
National Standards for OKSTU »
FINISHED ROLLED STEELS (INCLUDING BILL FOR EXPORT) »
Thin-sheet steel with a thickness of 1 to 1.8 mm »
The Document is Replaced With:
GOST 17066-94: Thin sheet rolled stock of high strength steel
As a Replacement Of:
GOST 17066-71: Sheets and coils of structural low-alloy steel. Grades and technical requirements
The Document References:
GOST 11701-84: Metals. Methods of tensile testing of thin sheets and strips
GOST 12344-88: Alloyed and high-alloyed steels. Methods of carbon determination
GOST 12345-88: Alloyed and high-alloyed steels. Methods of sulphur determination
GOST 12346-78: Alloyed and high-alloyed steels. Methods of silicon determination
GOST 12347-77: Alloyed and high-alloyed steels. Methods for determination of phosphorus
GOST 12348-78: Alloyed and high-alloyed steels. Methods of manganese determination
GOST 12349-83: Alloyed and high-alloyed steels. Methods for determination of tungsten
GOST 12350-78: Alloyed and high-alloyed steels. Methods of chromium determination
GOST 12351-81: Steels alloyed and highalloyed. Methods for the determination of vanadium
GOST 12352-81: Steels alloyed and highalloyed. Methods for the determination of nickel
GOST 12353-78: Alloyed and high-alloyed steels. Methods of cobalt determination
GOST 12354-81: Steels alloyed and highalloyed. Methods for the determination of molybdenum
GOST 12355-78: Alloyed and high-alloyed steels. Methods of copper determination
GOST 12356-81: Steels alloyed and highalloyed. Methods of the determination of titanium
GOST 12357-84: Steels alloyed and highalloyed. Methods for the, determination of aluminium
GOST 12358-82: Steels alloyed and highalloyed. Methods for the determination of arsinic
GOST 12359-81: Steels carbon, alloyed and highalloyed. Methods for the determination of nitrogen
GOST 14019-80: Metals. Methods of bend tests
GOST 16523-89: Rolled sheets from carbon quality and ordinary steel for general purposes
GOST 18895-81: Steel. Method of photoelectric spectral analysis
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 19903-74: Hot-rolled steel sheets. Dimensions
GOST 19904-90: Cold-rolled steel sheets. Dimensions
GOST 28473-90: Iron, steel, ferroalloys, metal chromium and metal manganese. General requirements for methods of analysis
GOST 7564-73: Steel. General rules of samples, blanks and test pieces for mechanical and technological tests
GOST 7565-81: Iron, steel and alloys. Sampling for determination of chemical composition
GOST 7566-81: Rolled stock and products for further treatment
The Document is Referenced By:
GOST 10551-75: Steel roll-formed corrugated sections. Range
GOST 17066-94: Thin sheet rolled stock of high strength steel
GOST 17380-83: Seamless welded steel pipeline components for Pn £ 10 MPa (£ 100 kgf/cm2). Specifications
GOST 27702-88: Steel and alloys. Unified grades
Manual for SNiP II-23-81*: Manual on the design of steel structures of overhead power lines (VL) power transmission towers and outdoor switchgears (outdoor switchgear) of substations with voltages above 1 kV
Manual for SNiP II-23-81*: Strength Design Guide for Steel Structures
Manual for SNiP II-23-81*: Steel Structural Engineering Tutorial
OST 26-01-1512-76: Axial lens compensators for PN <= 2,5 MPa (25 kgf / cm2). Technical requirements
OST 26-01-66-86: cap trays for steel columns. Parameters, design and dimensions.
OST 36-146-88: Bearings for steel industrial pipelines for P 10 MPa. Specifications.
OST 36-60-81: Welding at installation of steel building constructions. Main provisions.
RD 24.030.142-88: Methodological instructions. Selection of steel products for construction of stationary boilers.
RD 24.031.15-88: Methodological instructions. Designing stationary boilers steelworks.
RD 34.10.353: Specified Quantity Allowances for Materials for Repair of Electric Motors
RD 34.10.354-88: Transformers Consumption of materials for repair
RST RSFSR 91-78: Percussion musical instruments. General technical requirements
TU 36-2287-80: Bent closed welded square and rectangular profiles
TU 67-18-163-93: Three-layer wall frameless panels with steel cladding and mineral wool insulation. Technical conditions
TU 67-18-172-94: Roofing and wall three-layer frame panels with steel linings and mineral wool insulation. Technical conditions
TU 67-411-82: 10HNDP and 10HDP steel profiles, cold-formed with trapezoidal corrugation for construction. Technical conditions. Experimental batch 15000 t
VSN 10-83/Minhimprom: Instruction on designing of oxygen gas pipelines
Customers Who Viewed This Item Also Viewed:
 |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
High strength rolled steel. General specification
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads
Language: English |
Articulated connector devices with cast male and female parts for freight cars of articulated type. General technical specifications
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.