GOST 22762-77
ГОСТ 22762-77
|
|
Metals and alloys. Yield point hardness test by ball indentation
Металлы и сплавы. Метод измерения твердости на пределе текучести вдавливанием шара
Status: Effective. The limitation of the effectiveness period has been lifted: Protocol No. 3-93 of the IGU dated 03.03.93 (IUS 5-6-1993)
The standard applies to ferrous and non-ferrous metals and alloys and establishes a method for measuring hardness at a yield strength of 78.5 to 3285 MPa (8-335 kgf
Стандарт распространяется на черные и цветные металлы и сплавы и устанавливает метод измерения твердости на пределе текучести от 78,5 до 3285 МПа (8-335 кгс/мм.кв) путем вдавливания шара при температуре от 0 до плюс 40°С.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstandart of the USSR,
10/31/1977
SKU: RUSS56767
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
2 Tests for external factors »
2.2 Testing of manufacturing products »
ISO classifier »
77 METALLURGY »
77.040 Metal Testing »
77.040.10 Mechanical testing of metals »
National standards »
77 METALLURGY »
77.040 Metal Testing »
77.040.10 Mechanical testing of metals »
National Standards for KGS (State Standards Classification) »
Latest edition »
V Metals and metal products »
V0 General rules and regulations on metallurgy »
V09 Test methods. Packaging. Marking »
National Standards for OKSTU »
CAST IRON, FERRO ALLOYS, STEEL »
Control methods (testing, analysis, measurements) »
National Standards for OKSTU »
FINISHED ROLLED STEELS (INCLUDING BILL FOR EXPORT) »
Control methods (testing, analysis, measurements) »
National Standards for OKSTU »
RAW MATERIALS OF NON-FERROUS METALS, NON-FERROUS METALS AND THEIR ALLOYS »
Control methods (testing, analysis, measurements) »
The Document References:
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 3722-60: Ball bearings. Balls. Technical requirements
GOST 3722-81: Rolling bearings. Balls. Technical requirements
GOST 8.043-72: The State Measurement System. Instruments for measuring the hardness of metals and alloys using the Brinell method. Methods and means of verification
The Document is Referenced By:
GOST 29212-91: Plain bearings. Hardness testing of bearing metals. Compound materials
I 1.2.1.02.019.1121-2016: Determination of mechanical properties of metal of equipment of nuclear power plants by means of non-reference technique in terms of hardness characteristics. Instructions
I3-94: Instructions for diagnosing the technical condition of tanks of liquefied gas installations
ITNJe-93: Instruction on technical supervision and operation of pressure vessels not covered by the Rules of Gosgortechnadzor
MU 2002-2002: Methodology for examining the technical condition of cabinet elevators for drill and casing KM type and cast elevators for casing EN type to determine the possibility of their further operation
MU 9001.00.001: Diagnostic technique for Romanian fountain fittings that have worked out their standard service life
ODM 218.2.044-2014: Recommendations for the performance of instrument and instrumental measurements in assessing the technical condition of bridge structures on highways
OST 26.260.480-2003: Two-ply steel vessels and devices. Welding and weld deposition.
RD 03-380-00: Guidelines for Inspection of Spherical Tanks and Gas Holders for Storage of Liquefied Gases Under Pressure
RD 03-421-01: Guidelines for the diagnosis of the technical condition and the determination of the residual service life of vessels and apparatus
RD 08-95-95: Provision on the system for technical diagnostics of welded vertical cylindrical oil and petroleum products tanks
RD 09-244-98: Instructions for diagnostics of technical condition of vessels, pipes and compressors, industrial ammonia refrigeration plants.
RD 10-109-96: Guidelines for drawing up category IV pipeline passports
RD 153-34.1-21.530-99: Procedural Guidelines for Inspection of Structural Elements of Process Buildings and Structures of Thermal Power Stations. Part 2: Metal Structures
RD 22-326-97: Self-propelled jib cranes and loader cranes. Overhaul. General technical conditions
RD 26.260.12-99: Service life extension of liquid carbon dioxide vessels. Instructional guidelines.
RD 26.260.16-2002: Expert technical diagnostics of vessels and equipment operating under pressure at gas and gas condensate and oil production and processing facilities in the northern regions of the Russian Federation and underground gas storage facilities
RD 2-97: Regulations on the system for the technical diagnosis of autoclaves in the production of building materials
RD 34.17.435-95: Methodological instructions. Technical diagnostics of boilers with working pressure up to 4.0 MPa inclusive.
RD 34.40.601-97: Procedural Guidelines for Inspection of Hot Water Storage Tanks
RD EO 0027-2005: Instructions for determining the mechanical properties of metal of equipment of nuclear power plants using gumless methods according to hardness characteristics
RD EO 1.1.2.99.0867-2012: Methods for assessing the technical condition and residual life of building structures of nuclear power plants
RD NIIKranostroeniya 03-05: Guidelines. Jib cranes for general use and cranes; Overhaul. General specifications
RD RosJeK 05-014-98: Guidelines for expert examination of pipelines of steam and hot water of category IV, supervised by the Gosgortekhnadzor of Russia
SDA 24-2008: Rules for assessment (certification) of testing laboratories personnel
ST CKBA 125-2020: Pipe fittings. Types of control and testing
ST TsKBA 024-2006: Pipe fittings. Determination of residual life and reliability indicators
|
Customers Who Viewed This Item Also Viewed:
 |
State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 5. Measurement procedure
Language: English |
Petroleum products. Method for measurement of viscosity by automatic capillar viscosimeter
Language: English |
Greases. Method for determination of ultimate strength and thermostrengthening
Language: English |
Electric heating devices for heating rolling stock railways. Safety requirements and test methods
Language: English |
Ice cream. General technical requirements
Language: English |
Pipe fittings. Ball valves made of brass. General specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
