GOST 28232-89
ГОСТ 28232-89
|
|
Basic environmental testing procedures. Part 2. Tests. Guidance on the application of the tests of IEC publication 68 to simulate the effects of storage
Основные методы испытаний на воздействие внешних факторов. Часть 2. Испытания. Руководство по применению испытаний стандартов МЭК 68 (ГОСТ 28198-89 - ГОСТ 28236-89) для имитации воздействий хранения
Status: Effective - Introduced for the first time. IUS 12-1989
The storage test is intended to simulate the phenomena that occur as a result of the action of one or several external factors on the product during the normal storage period and in cases where the accumulation of fatigue phenomena is likely
Испытание на хранение предназначено для имитации явлений, возникающих в результате воздействия одного или нескольких внешних факторов на изделия в течение нормального срока хранения и в тех случаях, когда вероятно накопление усталостных явлений
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
8/15/1989
SKU: RUSS56899
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
2 Tests for external factors »
2.1 General requirements for tests on external factors »
ISO classifier »
19 TESTS »
19.040 Climatic tests »
National standards »
19 TESTS »
19.040 Climatic tests »
ISO classifier »
31 ELECTRONICS »
31.020 Electronic components in general »
National standards »
31 ELECTRONICS »
31.020 Electronic components in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
E Electronic engineering, electronics and communications »
E2 Elements of electronic equipment »
E29 Test methods. Packaging. Marking »
National Standards for OKSTU »
ELECTRONIC EQUIPMENT PRODUCTS. RESISTORS »
National Standards for OKSTU »
ELECTRONIC EQUIPMENT PRODUCTS. CONDENSERS »
National Standards for OKSTU »
ELECTRONIC EQUIPMENT PRODUCTS. SEMICONDUCTOR DEVICES AND INTEGRAL MICROCIRCUITS »
National Standards for OKSTU »
ELECTRONIC PRODUCTS, EXCEPT RESISTORS, CAPACITORS, SEMICONDUCTOR DEVICES AND INTEGRAL MICROCIRCUITS »
The Document References:
GOST 28198-89: Basic environmental testing. Part 1. General and quidance
GOST 28199-89: Basic environmental, testing procedures. Part 2. Tests. Test A: Cold
GOST 28200-89: Basic environmental testing procedures. Part 2. Tests. Test B: Dry heat
GOST 28201-89: Basic environmental testing procedures. Part 2. Tests. Test Ca: Damp heat, steady state
GOST 28202-89: Basic environmental testing. Part 2. Tests. Test Sa: Simulated solar radiation at ground level
GOST 28203-89: Basic environmental testing procedures. Part 2. Tests. Test Fc and guidance: Vibration ( sinusoidal )
GOST 28204-89: Basic environmental testing procedures. Part 2. Tests. Test Ga and quidance: Acceleration, steady state
GOST 28205-89: Basic environmental testing procedures. Part 2. Tests. Guidance for solar radiation testing
GOST 28206-89: Basic environmental testing procedures. Part 2. Tests. Test J. and quidance: Mould growth
GOST 28207-89: Basic environmental testing procedures. Part 2. Tests. Test Ka: Salt mist
GOST 28208-89: Basic environmental testing procedures. Part 2. Tests. Test M: Low air pressure
GOST 28209-89: Basic environmental testing procedures. Part 2. Tests. Test N: Change of temperature
GOST 28210-89: Basic environmental testing procedures. Part 2. Tests. Test Q: Sealing
GOST 28211-89: Basic environmental testing procedures. Part 2. Tests. Test T: Soldering
GOST 28212-89: Basic environmental testing procedures. Part 2. Tests. Test U: Robustness of terminations and integral mounting devices
GOST 28213-89: Basic environmental testing prosedures. Part 2. Tests. Test Ea and guidance: Shock
GOST 28214-89: Basic environmental testing procedures. Part 2: Tests. Guidance for damp heat tests
GOST 28215-89: Basic environmental testing procedures. Part 2. Tests. Test Eb and quidance: Bump
GOST 28216-89: Basic environmental testing procedures. Part 2. Tests. Test Db and guidance: damp heat, cyclic (12 + 12 hour cycle)
GOST 28217-89: Basic environmental testing. Part 2. Tests. Test Ec: Drop and Topple, primarily for equipment-type specimens
GOST 28218-89: Basic environmental testing procedures. Part 2. Tests. Test Ed: Free fall
GOST 28220-89: Basic environmental testing procedures. Part 2. Tests. Test Fd: Random vibration wide band. General requirements
GOST 28221-89: Basic environmental testing procedures. Part 2. Tests. Test Fda: Wide band random vibration. High reproducibility
GOST 28222-89: Basic environmental testing procedures. Part 2. Tests. Test Fdb: Random vibration wide band. Reproducibility medium
GOST 28223-89: Basic environmental testing procedures. Part 2. Tests. Test Fdc: Random vibration, wide band. Reproducibility low
GOST 28224-89: Basic environmental testing procedures. Part 2. Test Z/AD. Composite temperature and humidity cyclic test
GOST 28225-89: Basic environmental testing procedures. Part 2. Tests. Test Z/AMD: Combined sequential cold, low air pressure and damp heat test
GOST 28226-89: Basic environmental testing procedures. Part 2. Tests. Test Kc: Sulphur dioxide test for contacts and connections
GOST 28227-89: Basic environmental testing procedures. Part 2. Tests. Test Kd: Hydrogen sulphide test for contacts and connections
GOST 28228-89: Basic environmental testing procedures. Part 2. Tests. Guidance on test T: Soldering
GOST 28229-89: Basic environmental testing procedures. Part 2. Tests. Test XA and guidance. Immersion in cleaning solvents
GOST 28230-89: Basic environmental testing. Part 2. Tests. Guidance to test Kd: Hydrogen sulphide test for contacts and connections
GOST 28231-89: Basic environmental testing procedures. Part 2. Tests. Mounting of components, equipment and other articles for dynamic tests including shock (Ea), bump (Eb), vibration (Fc and Fd) and steady-state acceleration (Ga) and guidance
GOST 28233-89: Basic environmental testing procedures. Part 2. Tests. Guidance to test Kc: Sulphur dioxide test for contacts and connections
GOST 28234-89: Basic environmental testing procedures. Part 2. Tests. Test Kb: Salt mist, cyclic (sodium chloride solution)
GOST 28235-89: Basic environmental testing procedures. Part 2. Tests. Test Ta: Soldering. Solderability testing by the wetting balance method
GOST 28236-89: Basic environmental testing procedures. Part 3. Background information. Section 1. Cold and dry heat tests
The Document is Referenced By:
GOST 14014-91: Digital instruments and measuring transducers of voltage, current and resistance
GOST 28198-89: Basic environmental testing. Part 1. General and quidance
GOST 28578-90: Semiconductor devices. Mechanical and climatic test methods
GOST 30012.1-2002: Direct acting indicating analogue electrical measuring instruments and their accessories. Part 1. Definitions and general requirements common to all parts
GOST 30012.1-93: Direct acting indicating analogue electrical measuring instruments and their accessories. Part 1. Definitions and general requirements common to all parts
GOST IEC 62040-3-2009: Guaranteed power supply systems. Uninterruptible power supply units. Part 3. General technical requirements. Test methods
GOST R 50736-95: Antenna-feeder devices of systems of land mobile radiocommunication. Types, basic parameters, technical requirements and methods of measurements
GOST R 56462-2015: Systems of the prevention automatic about penetration into objects of transport infrastructure and vehicles. Electronic sealing devices. General requirements
GOST R IEC 60945-2007: Maritime navigation and radiocommunication equipment and systems. General requirements. Methods of testing and required test results
GOST R IEC 61969-1-2013: Mechanical structures for electronic equipment. Outdoor enclosures. Design guidelines
GOST R IEC 61969-3-2015: Mechanical structures for electronic equipment. Outdoor enclosures. Part 3. The environmental demands concern, testing and safety
|
Customers Who Viewed This Item Also Viewed:
 |
Jet fuels
Language: English |
State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 5. Measurement procedure
Language: English |
Molded parts of coupler and automatic coupler devices of railway rolling stock. General specifications.
Language: English |
Main-line diesel locomotives. General technical requirements.
Language: English |
Four-wheel bogies of freight cars for mainline railways gauge 1520 (1524) mm. Specifications
Language: English |
Technical ethylcellosolve. Specifications
Language: English |
Automatic coupler model SA-3 and its components. Design and dimensions
Language: English |
Railway rolling stock. Devices to prevent running gear parts from dropping to the track. Methods of controlling strength characteristics
Language: English |
Electric heating devices for heating rolling stock railways. Safety requirements and test methods
Language: English |
Ice cream. General technical requirements
Language: English |
Welded joints in steel structures of railway rolling stock. Requirements for design, implementation and quality control
Language: English |
Locomotives The method of dynamic strength tests
Language: English |
Railway rolling stock. Norms for permissible exposure of railway track and test methods
Language: English |
Locomotives. Requirements for strength and dynamic qualities
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
