GOST 28204-89
ГОСТ 28204-89
|
|
Basic environmental testing procedures. Part 2. Tests. Test Ga and quidance: Acceleration, steady state
Основные методы испытаний на воздействие внешних факторов. Часть 2. Испытания. Испытание Gа и руководство: Линейное ускорение
Status: Effective - Introduced for the first time. IUS 12-1989
The purpose of this test is to check the suitability of the design and performance of elements, equipment and other electrical products in the presence of forces arising from the effects of linear acceleration (other than acceleration of gravity), which take place in moving vehicles, in particular in aircraft, rotating parts and shells, as well as the development of methods for testing structural strength for some elements
Целью настоящего испытания является проверка пригодности конструкции и работоспособности элементов, аппаратуры и других электротехнических изделий при наличии сил, возникающих при воздействии линейного ускорения (отличного от ускорения силы тяжести), которые имеют место в движущихся транспортных средствах, в частности в летательных аппаратах, вращающихся деталях и снарядах, а также разработка методики испытания конструктивной прочности для некоторых элементов
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
8/15/1989
SKU: RUSS61456
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
2 Tests for external factors »
2.1 General requirements for tests on external factors »
ISO classifier »
19 TESTS »
19.040 Climatic tests »
National standards »
19 TESTS »
19.040 Climatic tests »
ISO classifier »
31 ELECTRONICS »
31.020 Electronic components in general »
National standards »
31 ELECTRONICS »
31.020 Electronic components in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
E Electronic engineering, electronics and communications »
E2 Elements of electronic equipment »
E29 Test methods. Packaging. Marking »
National Standards for OKSTU »
ELECTRONIC EQUIPMENT PRODUCTS. RESISTORS »
National Standards for OKSTU »
ELECTRONIC EQUIPMENT PRODUCTS. CONDENSERS »
National Standards for OKSTU »
ELECTRONIC EQUIPMENT PRODUCTS. SEMICONDUCTOR DEVICES AND INTEGRAL MICROCIRCUITS »
National Standards for OKSTU »
ELECTRONIC PRODUCTS, EXCEPT RESISTORS, CAPACITORS, SEMICONDUCTOR DEVICES AND INTEGRAL MICROCIRCUITS »
The Document References:
GOST 28198-89: Basic environmental testing. Part 1. General and quidance
GOST 28231-89: Basic environmental testing procedures. Part 2. Tests. Mounting of components, equipment and other articles for dynamic tests including shock (Ea), bump (Eb), vibration (Fc and Fd) and steady-state acceleration (Ga) and guidance
The Document is Referenced By:
GOST 14014-91: Digital instruments and measuring transducers of voltage, current and resistance
GOST 28198-89: Basic environmental testing. Part 1. General and quidance
GOST 28232-89: Basic environmental testing procedures. Part 2. Tests. Guidance on the application of the tests of IEC publication 68 to simulate the effects of storage
GOST 28578-90: Semiconductor devices. Mechanical and climatic test methods
GOST 30012.1-2002: Direct acting indicating analogue electrical measuring instruments and their accessories. Part 1. Definitions and general requirements common to all parts
GOST 30012.1-93: Direct acting indicating analogue electrical measuring instruments and their accessories. Part 1. Definitions and general requirements common to all parts
GOST 33897-2016: Railway telecommunications. Safety requirement control methods
GOST IEC 61810-7-2013: Electromechanical elementary relays. Part 7. Test and measurement procedures
GOST R 50736-95: Antenna-feeder devices of systems of land mobile radiocommunication. Types, basic parameters, technical requirements and methods of measurements
GOST R 54958-2012: Railway telecommunications. Safety requirement control methods
GOST R IEC 1007-96: Transformers and inductors for use in electronic and telecommunication equipment. Measuring methods and test procedures
GOST R IEC 60122-1-2009: Quartz crystal units of assessed quality. Part 1. Generic specification
GOST R IEC 61969-1-2013: Mechanical structures for electronic equipment. Outdoor enclosures. Design guidelines
GOST R IEC 61969-3-2015: Mechanical structures for electronic equipment. Outdoor enclosures. Part 3. The environmental demands concern, testing and safety
OST 32.146-2000: Devices of railway automation, telemechanics and telecommunications. General specification requirements
|
Customers Who Viewed This Item Also Viewed:
 |
State system for ensuring the uniformity of measurements. Measurements of liquids and gases flow rate and quantity by means of orifice instruments. Part 5. Measurement procedure
Language: English |
Petroleum products. Method for measurement of viscosity by automatic capillar viscosimeter
Language: English |
Greases. Method for determination of ultimate strength and thermostrengthening
Language: English |
Electric heating devices for heating rolling stock railways. Safety requirements and test methods
Language: English |
Ice cream. General technical requirements
Language: English |
Pipe fittings. Ball valves made of brass. General specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
