imgalt

GOST 8.326-89

ГОСТ 8.326-89

State system for ensuring the uniformity of measurements. Metrological certification measuring instruments

Государственная система обеспечения единства измерений. Метрологическая аттестация средств измерений

Status: Not effective - Canceled in the Russian Federation

The standard applies to: working and exemplary measuring instruments, as well as calibration facilities that are not subject to state testing according to GOST 8.001; measuring channels included in the system of automatic or automated measurement, control, management and other systems (complexes), not intended for mass production; single copies of serial production measuring instruments used in conditions and modes that differ from conditions and modes for which their metrological characteristics are normalized, or in the design of which changes have been made that affect these characteristics experimental (head) and experimental samples of measuring instruments (with the exception of samples that have passed state acceptance tests with positive results), made in the process of performing experimental design and research works, transferred to operation; measuring instruments purchased by import in single copies or in small batches. This standard establishes the general requirements for the organization and procedure for metrological certification of measuring instruments, as a type of state metrological supervision and departmental control.

Стандарт распространяется на: рабочие и образцовые средства измерений, а также поверочные установки, не подлежащие государственным испытаниям по ГОСТ 8.001; измерительные каналы, входящие в системы автоматического или автоматизированного измерения, контроля, управления и другие системы (комплексы), не предназначенные для серийного производства; единичные экземпляры средств измерений серийного выпуска, применяемые в условиях и режимах, отличающихся от условий и режимов, для которых нормированы их метрологические характеристики, либо в конструкцию которых внесены изменения, влияющие на эти характеристики; опытные (головные) и экспериментальные образцы средств измерений (за исключением образцов, прошедших государственные приемочные испытания с положительными результатами), изготовленные в процессе выполнения опытно-конструкторских и научно-исследовательских работ, передаваемые в эксплуатацию; средства измерений, приобретаемые по импорту в единичных экземплярах или мелкими партиями. Настоящий стандарт устанавливает общие требования к организации и порядку проведения метрологической аттестации средств измерений, как разновидности государственного метрологического надзора и ведомственного контроля

Choose Language: 
Format: Electronic (pdf/doc)

Approved: USSR State Committee for Product Quality and Standards Management, 12/5/1989

SKU: RUSS62753

Price: $267.00



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 17 Metrology and measurements. Physical phenomena »

ISO classifier » 17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA » 17.020 Metrology and measurements in general »

National standards » 17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA » 17.020 Metrology and measurements in general »

National Standards for KGS (State Standards Classification) » Latest edition » T General technical and organizational and methodological standards » T8 State measurement system » T80 Rules, norms, regulations infield of ensuring uniformity of measurements »

National Standards for OKSTU » SYSTEMS OF GENERAL TECHNICAL AND ORGANIZATIONAL-METHODOLOGICAL STANDARDS » State system for ensuring the uniformity of measurements (GSI) »


As a Replacement Of:

GOST 8.326-78: The State Measurement System. Metrological assurance of development, manufacturing and operation of unstandardized measuring instruments. General principles

The Document References:

GOST 16263-70: State system for ensuring the uniformity of measurements. Metrology. Terms and definitions

GOST 2.601-68: Unified system for design documentation. Exploitative documents

GOST 2.601-95: Operational documents

GOST 28.001-83: System of technical maintenance and repair of equipment. Basic provisions

GOST 8.001-80: State system of ensuring the unity of measurements. Rules for conducting the state tests of measuring means

GOST 8.009-84: State system for ensuring the uniformity of measurements. Standardized metrological characteristics of measuring instruments

GOST 8.513-84: State system for ensuring the uniformity of measurements. Verification of measuring instruments. Organization and procedure

MI 1314-86: State system for ensuring uniformity of measurements. The order of the metrological examination of technical tasks for the development of measuring instruments. Methodical instructions

MI 202-80: State system for ensuring uniformity of measurements. Metrological characteristics of measuring systems. Principles of regulation and control. Main provisions

RD 50-660-88: Instructions. State system for ensuring uniformity of measurements. Documents on methods of calibration of measuring instruments

The Document is Referenced By:

GOST 10180-2012: Concretes. Methods for strength determination using reference specimens

GOST 10180-90: Concretes. Methods for strength determination using reference specimens

GOST 10181-2000: Concrete Mixtures Test method

GOST 10181-2014: Concrete mixtures. Methods of testing

GOST 10574-91: Meat products. Determination of starch content

GOST 10629-88: Prestressed reinforced concrete sleepers for 1520 mm gauge railways. Specifications

GOST 10702-78: Steel bars, carbon and alloy, structural, for cold extruding and upsetting. Specifications

GOST 10922-90: Welded reinforcing products and inserts, welded joints of reinforcement and inserts for reinforced concrete structures. General specifications

GOST 11030-93: Motor graders

GOST 11268-76: Structural thin sheets of special purpose alloyed high quality steel

GOST 11269-76: Universal rolled plates and wide strips made of special purpose structural high-grade Alloy steel

GOST 11310-90: Asbestos cement pipes and couplings. Methods of test

GOST 12.0.005-84: Occupational safety standards system. Metrological support of occupational safety. General

GOST 12.3.016-87: Occupational safety standards system. Building construction anticorrosive protective works. Safety requirements

GOST 12252-86: Angle modulation radio stations of land mobile service. Types. Basic parameters. Technical requirements. Methods of measurement

GOST 1293.15-90: Antimonous lead alloys. Spectrographical method for determination of nickel

GOST 1293.16-93: Lead-antimony alloys. Methods for determination of sulphur

GOST 12997-84: SSI Products. General specifications

GOST 13348-74: Antimonous antimonides. Method of spectral analysis

GOST 13822-82: Generating sets and moving diesel-power stations. General specifications

GOST 13938.13-93: Copper. Methods of determination of oxygen

GOST 13981-87: Forms for reinforced concrete pressure pipes made by vibrohydropressed method. Specifications

GOST 14050-93: Limestone meal (dolomite)

GOST 14080-78: Precision alloy strip with specified temperature coefficient of linear expansion. Specifications

GOST 14162-79: Steel tubes of small dimensions (capillary)

GOST 1435-99: Bars, strips and reels of tool unalloyed steel. General specifications

GOST 14657.0-78: Bauxite. General requirements for methods of chemical analysis

GOST 14657.0-96: Bauxite. General requirements for methods of chemical analysis

GOST 14662-83: Radiotelegraph channel receiving-transmitting equipment

GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods

GOST 14896-84: Rubber u-packing seals for hydraulic devices

GOST 14959-79: Spring carbon and alloy steel bars. Specifications

GOST 1577-93: Plate and broadband roll stock of construction fine steel.

GOST 15848.0-90: Chromium ores and concentrates. General requirements for methods of chemical analysis

GOST 16312-97: Electric motor frequency convertors with rated power up to 200 kW and frequency to 20000 Hz. Test methods

GOST 16765-87: General-purpose self-propelled boom cranes. Acceptance and testing methods

GOST 17152-89: Steel hot-rolled shapes for cutting blades of earth-moving machines. General specifications

GOST 17623-87: Concrete. Radioisotope method of average density determination

GOST 19277-73: Seamless steel tubes for oil and fuel lines. Specifications

GOST 19347-99: Copper sulfate. Technical conditions

GOST 20068.1-79: Tintess bronze. Method of spectral analysis of metal standard specimens with spectrum photographic record

GOST 20068.2-79: Tints bronze. Method of spectral analysis of metal standard specimens with spectrum photo-electric record

GOST 20068.3-79: Tints bronze. Method of spectral analysis of oxide standard specimens with spectrum photographic record

GOST 21395.0-75: Resistors. Method of control of requirements for design. General

GOST 21520-89: Small-sized wall blocks of cellular concrete. Specifications

GOST 21792-89: Shipboard diesel installations. Acceptance and methods of ship trials

GOST 22011-95: Passenger and freight elevators

GOST 22261-94: Measuring instruments for electrical

GOST 22343-90: Clamp for indirect rail fastening of railways. Specifications

GOST 22579-86: Single-sideband modulation radio stations of land mobile service. Types, basic parameters, technical requirements and methods of measurement

GOST 22598-93: Nickel and low nickel base alloys. Method of determination of oxygen

GOST 22663-77: Thermoelectrode materials for low-temperature thermocouples. Method of homogeneity test

GOST 22690-88: Concretes. Determination of strength by mechanical methods of nondestructive testing

GOST 22904-93: Reinforced concrete structures. Magnetic method for determining the thickness of the protective layer of concrete and the location of reinforcement

GOST 23117-91: Semiautomatic grips for tensioning of the steel in prestressed concrete structures. Specifications

GOST 23189-78: Primary aluminium. Spectrochemical method for the determination of arsenic and lead

GOST 24018.0-90: Nickel-based high-temperature strong alloys

GOST 24282-86: Flexible-way electric powered vehicles. Testing methods

GOST 24282-97: Floor-mounted flexible electrified vehicles. Testing methods

GOST 24607-88: Semiconductor frequency converters

GOST 24940-96: Buildings and structures. Methods of measuring luminance

GOST 25051.2-82: The state system of testing products. Test chambers of heat and cold. Certification methods

GOST 25051.4-83: Electrodynamic vibration testing equipment. General specifications

GOST 25086-87: Nonferrous metals and their alloys. General requirements for methods of analysis

GOST 25542.0-93: Alumina. General requirement for methods of chemical analysis

GOST 25792-85: Radio receivers for marine mobile service

GOST 25804.4-83: Atomic power station technological processes control system equipment. General design-constructional requirements

GOST 25932-83: Portable radioisotope soil and concrete moisture and density gauges. General specifications

GOST 25959-83: Tractor and combine diesels. Acceptance

GOST 26.203-81: Measure-computering complexes. Classification. General requirements

GOST 26318.0-84: Non-metallic ore materials. General requirements for methods of analysis

GOST 2642.0-86: Refractories and refractory raw materials. General requirements for methods of analysis

GOST 26602.4-99: Windows and doors. Method of determination of total light transmittance

GOST 26712-94: Organic fertilizers. General requirements for methods of analysis

GOST 26807-86: Airborne digital apparatus for aircraft and helicopters. Standing test methods for working capacity under electromagnetic action conditions

GOST 26897-86: Single-sideband modulation radio stations of marine mobile service. Types, basic parameters, technical requirement and methods of measurement

GOST 26980-95: Single bucket excavators. General specifications

GOST 27173-86: Spectrometric units and devices for detection of ionizing radiation

GOST 27338-93: Concrete mixing plant

GOST 27339-93: Mixer trucks

GOST 27445-87: Neutron flux monitoring systems for control and protection of nuclear reactors. General technical requirements

GOST 27598-94: Running rollers road vibration self-moving

GOST 27614-93: Cement carriers

GOST 27809-95: Cast iron and steel. Methods of spectrographic analysis

GOST 27811-95: Tar pavers

GOST 27816-88: Asphalt paver. Test methods

GOST 27945-95: Asphalt mixing plants

GOST 28052-97: Titanium and titanium alloys. Methods of oxygen determination

GOST 28089-89: Wall masonry constructions. Test method for bond strength of facing tiles with the base

GOST 28276-89: Surface acoustic wave devices. Types, main parameters and methods of measurements

GOST 28393-89: PM bars and strips of high-speed steel. General specifications

GOST 28439-90: Equipment of digital, fiber optic transmission systems over power lines

GOST 28570-2019: Concrete Methods for determining the strength of samples taken from structures

GOST 28570-90: Concretes. Methods of strength evaluation on cores drilled from structures

GOST 28871-90: Line transmission path equipment of digital optical-fibre transmission systems. Methods of measuring basic parameters

GOST 28944-91: Welding mechanical equipment. Test methods

GOST 29075-91: Nuclear instrumentation systems for nuclear power stations. General requirements

GOST 29234.0-91: Moulding sands. General requirements for test methods

GOST 29269-91: Soils. General requirements for the fulfilment of analyses

GOST 30035-93: Scrapers. General specifications

GOST 30062-93: Bar reinforcement for reinforced concrete structures

GOST 30067-93: Universal single bucket full turning excavators

GOST 30082-93: Zinc-aluminium alloys. Spectral method of analysis

GOST 30108-94: Building materials and elements. Determination of specific activity of natural radioactive nuclei

GOST 30109-94: Wooden doors. Test methods for the breaking resistance

GOST 30336-95: Electromagnetic compatibility of technical equipment. Immunity to pulse magnetic field. Technical requirements and test methods

GOST 30379-95: Electromagnetic compatibility of technical means of protection fire-alarm and fire-protection systems. Requirements, standards and methods of tests on interference immunity and industrial interference

GOST 30421-96: Electrical capacitance, pure resistance and dissipation factor high-voltage meters. General specifications

GOST 30585-98: Electromagnetic compatibility of engineering facilities. Resistance to the action of lightning discharges. Technical requirements and test methods.

GOST 30605-98: Digital voltage and current measuring converters. General specifications

GOST 30646-99: Central conditioners of general use. General specifications.

GOST 310.5-88: Cements. Test method for heat of hydration

GOST 31817.1.1-2012: Alarm systems. Part 1. General requirements. Section 1. General

GOST 3221-85: Primary aluminium. Methods of spectral analysis

GOST 32320-2013: Anti-theft protection technical means and systems. General requirements and test methods

GOST 32321-2013: Alarms guarding surface shock-contact glass break detectors for use in buildings. General requirements and test methods

GOST 3519-91: Optical materials. Methods of determination of birefringence

GOST 3594.0-93: Moulding refractory clays. Generals requirements for tests

GOST 4543-71: Structural alloyed steel

GOST 5267.0-90: Hot-rolled sections for car building. General specifications

GOST 535-88: Common quality carbon bar and shaped sections. General specifications

GOST 5382-91: Cements and materials for cement production. Chemical analysis methods

GOST 5496-78: Rubber technical tubes. Specifications

GOST 6051-76: Hollow rubberfabric gaskets. Specifications

GOST 6678-72: Rubber sealing cups for pneumatic apparatus. Specifications

GOST 7338-90: Rubber and rubber-fabric sheets. Specifications

GOST 8.315-97: Standard samples for composition and properties of substances and materials

GOST 8.519-84: State system for ensuring the uniformity of measurements. Dielcometric moisture meters for construction materials. Calibration methods

GOST 8.560-94: State system for ensuring the uniformity of measurements. State verification schedule for measure of electric field intensity measuring within frequency range 0.0003-1000 MGz

GOST 8269.0-97: Mauntainous rock road-metal and gravel, industrial waste products for construction works. Methods of physical and mechanical tests

GOST 8269.1-97: Mauntainous rock road-metal and gravel, industrial waste products for construction works Methods clicmical analysis

GOST 8478-81: Welded meshes for reinforced concrete structures. Specifications

GOST 8558.1-78: Meat products. Methods for determination of nitrite

GOST 8735-88: Sand for construction work. Testing methods

GOST 8747-88: Asbestos-cement sheet products. Test methods

GOST 9.030-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing resistance to attack by corrosive media in limp state

GOST 9038-90: Gauge blocks. Specifications

GOST 9716.1-79: Copper-zinc alloys. Method of spectral analysis of metal standard specimens with photographic registration of spectrum

GOST 9716.2-79: Copper-zinc alloys. Method spectral analysis of metal standard specimens with photoelectric registration of spectrum

GOST R 50009-92: Electromagnetic compatibility of technical means of protection fire-alarm and fire-protection systems. Requirements, standards and methods of tests on interference immunity and industrial interference

GOST R 50015-92: Electromagnetic compatibility for consumer video tape recorders. Immunity to electromagnetic disturbance. Test methods

GOST R 50084-92: Truck mixer. General specifications

GOST R 50414-92: Electromagnet compatibility of technical means. Test equipment. Shielded chambers. Classes, general parameters, technical requirements and test methods

GOST R 50513-93: Refrigerating chambers for storage of table grapes. Certification methods

GOST R 50648-94: Electromagnetic compatibility of technical equipment. Immunity to power frequency magnetic field. Technical requirements and test methods

GOST R 50649-94: Electromagnetic compatibility of technical equipment. Immunity to pulse magnetic field. Technical requirements and text methods

GOST R 50730.1-95: Microwave ferrite devices. General requirements for measurement of parameters at high power level

GOST R 50950-96: Front end loaders with telescopic boom. General specifications

GOST R 51036-97: Electrooptical elements. Methods for measurement of electrooptical parameters

GOST R 51063-97: Inert powder. Methods of testing

GOST R 51106-97: Lasers injection, laser heads, lasers diodes matiсes, lasers diodes. Methods for measurement of parameters

GOST R 51363-99: Vibration hammers and pile extractors. General specifications

GOST R 51558-2000: Television systems of security. General technical requirements and test methods

GOST R 51601-2000: Building single-bucket loaders. Specifications

GOST R 51602-2000: Pile driving rigs. General specifications

GOST R 51666-2000: Cold self-propelled planers for road building purpose. General specifications

GOST R 51724-2001: Shielded facilities, spaces, installations. Reduced geomagnetic field. Measuring methods and assessment of field intensity compliance with technical requirements and hygiene standards

GOST R 51795-2001: Cements. Methods for determination of content of mineral additives

GOST R 51838-2001: Safety of machinery. Electrical equipment for industrial machines. Test methods

GOST R 57587-2017: Products obtained by additive processes. Methods of control and testing

Manual: Manual for impulse and low consumption fire extinguishing systems

MDS 12-1.98: Recommended Practice for Development of Quality Systems in Construction and Installation Organizations (Based on ISO 9000 Standards)

MDS 12-22.2005: Recommendations for the application in the construction industry of the requirements of regulatory legal and other regulatory acts containing state regulatory labor protection requirements

MI 1272-86: Guidelines. Thickness gauge ultrasonic UT-93P. Method of verification

MI 1619-87: State system for ensuring uniformity of measurements. PH meter and ionomer converter, pH meter kits. Method of verification

MI 1771-87: State system for ensuring uniformity of measurements. Ion-selective electrodes to determine the activity of ions in aqueous solutions. Method of verification

MI 1772-87: State system for ensuring uniformity of measurements. Auxiliary electrodes for potentiometric measurements. Method of verification

MI 1786-87: Guidelines. State system for ensuring uniformity of measurements. The main parameters of receiving acoustic emission transducers. Measurement Technique

MI 1862-88: Guidelines. State system of measurement uniformity. Measuring channels of dispatching telecontrol systems of oil and gas production facilities. Typical methodology and program of metrological certification

MI 1864-88: State system for ensuring uniformity of measurements. Fuel dispensers. Method of verification

MI 1985-89: Recommendation. State system for ensuring uniformity of measurements. Measures of inductance and mutual inductance. Method of verification

MI 2000-89: State system for ensuring uniformity of measurements. Aerodynamic pipes of small subsonic speeds. Methodology of metrological certification

MI 2002-89: State system for ensuring uniformity of measurements. Information measuring systems. Organization and procedure for metrological certification

MI 2079-90: Measures of length plane-end exemplary 3 and 5th digits and working classes of accuracy 1-5 up to 100mm.

MI 2116-90: Recommendations. GSE. Analysis and evaluation of metrological support in the implementation of ISO 9000 standards

MI 2186-92: Recommendation. GSOEI. Length measures are terminal flat-parallel model 3 and 4th digits and working classes of accuracy 1 - 5 with a length in excess of 100 to 1000 mm. Method of verification

MI 858-85: Guidelines. Metrological support of environmental monitoring. Certified mixtures of substances. Main provisions

NPB 192-2000: Fire engineering. Communnication and lighting truck. General technical requirements. Test methods

ODM 218.2.044-2014: Recommendations for the performance of instrument and instrumental measurements in assessing the technical condition of bridge structures on highways

ODM 218.3.042-2014: Recommendations for determining the parameters and assignment of categories of defects in assessing the technical condition of bridges on highways

Order 1815: The procedure for verification of measuring instruments, requirements for the verification mark and the content of the verification certificate

Order 2510: On approval of the procedure for verification of measuring instruments, requirements for the verification mark and the content of the verification certificate

OST 1-02557-85: Information and measuring systems for statistical breaking strength and endurance checkout. General requirements.

OST 108.030.124-85: Details and prefabricated units made of pearlitic steels for pipelines with environment pressure P>2.2 MPa (22 kg/cm2) in nuclear power plants. General Specifications.

OST 13-26.1-82: System for development and launch of new products. Production of woodworking industries

OST 24.125.60-89: Details and prefabricated units of steam and hot water in thermal power plants. General Specifications.

OST 45.90-96: Interfaces for digital channels and paths of basic interconnection Telecommunication network of Russian Federation. Measuring techniques for basic parameters

OST 45.91-96: Error performance measuring equipment for digital paths and channels. Technical requirements. Measuring techniques

OST 45.92-96: Metrological Service of the Ministry of Communications of the Russian Federation. Organizational structure. Tasks and interaction of structural units

OST 48-41-91: Engineering products of non-ferrous metallurgy. General Specifications.

OST 95 10575-2002: Equipment and pipelines of separation plants. Weld joints and deposits. Control rules

OTT 08042462: Instruments and automation equipment for nuclear power plants. General technical requirements

PNAE G-7-010-89: Equipment and pipelines of nuclear energy facilities. Welded joints and beads. Testing rules

POT R M-003-97: Intersectoral rules on labor protection when performing forging and pressing

R 50.4.004-2000: Accreditation of test labs for food products and raw material

R 50-54-80-88: Recommendations. Reliability in technology. Complex testing of engineering products for reliability. General provisions

R 50-609-48-88: Recommendations. Control of technological discipline. General provisions

RD 03-299-99: Requirements for acoustic emission equipment used to control hazardous production facilities

RD 10-117-95: Requirements for Installation and Safe Operation of Rail Tracks of Gantry Cranes

RD 153-34.0-03.504-00: Guidelines on Organization and Performance of Psychophysiological Examinations of Energy Facility Personnel

RD 153-34.0-21.529-98: Method for Inspection of Reinforced Concrete Tanks for Liquid Fuel Storage

RD 153-34.1-003-01: Welding, heat treatment and control of copper pipe systems and pipelines at power equipment installation and repair.

RD 153-39.4-056-00: Main crude pipeline. Operations rules.

RD 22-207-88: Lifting machines. General requirements and production standards

RD 22-322-02: Lifting cranes. Technical specifications for overhaul, complete and overhaul repairs

RD 24.020.11-93: Welded joints of stationary steam, gas and hydraulic turbines. Testing rules and quality evaluation standards.

RD 2730.940.103-92: Steam and hot water boilers, steam and hot-water-pipelines. Welding. General requirements.

RD 31.3.3-97: Guidelines on technical control of waterworks in maritime transport. Ministry of Transport, DMT Soyuzmorniiproekt, 1997

RD 31.3.4-97: Provision on organization of technical inspection of hydraulic facilities of marine transport

RD 31.44.01-97: Rules of technical operation of lifting and transport equipment of sea trading ports

RD 34.11.111-89: Methodology instructions. State analysis of metrological industrial support at energy providers and sectoral research institutes

RD 34.11.408-91: Model Program for Metrological Certification of Telemetry Channels of Operational Information Complex of Automated Dispatch Control System

RD 34.17.402: Guidelines for Surface Inspection of Cast Housing Components of Steam Turbines for Electric Power Generating Stations Prior to Operation

RD 39-5-649-81: Rules of industrial commissioning of petroleum quantity measuring systems

RD 45.023-98: Telecommunication Measurement Instruments. Methodical instructions for calibrating a digital signal analyzer of the Interceptor 147 type, an PCM-30 analyzer of the K4304 type, a PCM-1 type telephone channel meter Collection № 1. Methodological guidelines

RD 50-283-81: Guidelines. Certification of measuring hydrophones in the operating temperature range

RD 50-293-81: Guidelines. Oil and petroleum products. Certification of analyzers of composition and properties

RD 50-674-88: Methodological instructions. Measurement assurance of quantitative chemical analysis. Main provisions.

RD 50-700-91: Guidelines. Industrial particle accelerators. General requirements for the measurement of parameters

RD 52.08.15-97: Guidelines. Hydrometer river curlers type GR-21M, GR-55, GR-99, ISP-1 and VG-1-120/70 of the kit IST-1-0, 06/120/70. Work standards. Methods of metrological certification in a rectilinear calibration pool. State Hydrological Institute (GGI)

RD 52.10.324-92: Guidelines. Hydrological observations and work on the hydrometeorological network in the estuary areas of the rivers. State Oceanographic Institute (GOIN)

RD 52.18.191-89: Guidelines. Methods for measuring the mass fraction of acid-soluble forms of metals (copper, lead, zinc, nickel, cadmium) in soil samples by atomic absorption analysis

RD 52.18.289-90: Guidelines. Methods for measuring the mass fraction of mobile forms of metals (copper, lead, zinc, nickel, cadmium, cobalt, chromium, manganese) in soil samples by atomic absorption analysis. NGO "Typhoon"

RD 52.18.578-97: Guidelines. Mass fraction of the amount of polychlorbiphenyl isomers in soil samples. Methodology for measurement using gas-liquid chromatography

RMD 32-18-2012 Sankt-Peterburg: Recommendations for the use of paving in the paving of residential and public business areas

RTM 393-94: Technical Guides for welding and quality control of the joints of reinforcement and embedded items of concrete elements

Rules 2001: Rules for operation of technical means of television and radio broadcasting. Part 1. Television

Rules 2001: Rules for operation of technical means of television and radio broadcasting. Part 2. Broadcasting

Rules 2001: Rules for operation of technical means of television and radio broadcasting. Part 3. General safety requirements

SanPiN 2.6.1.012-94: Production of consumer goods on the factories of the atomic industry

SP 11-105-97: Engineering and geological survey for construction

SP 11-109-98: Prospecting for soil building materials

TU 14-2-767-88: Hot-rolled steel strip with improved quality. Technical conditions

TU 21-31-69-89: Gypsum fiber sheets. Technical conditions

TU 34-38-20219-94: Economizers smooth tube steam stationary boilers. Technical conditions for major repairs

TU 34-38-20220-94: Smooth tube steam stationary boilers with natural circulation screens. Technical conditions for major repairs

TU 34-38-20222-94: Steam superheaters of stationary steam boilers. Technical conditions for major repairs

VMU-20-90: Temporary guidelines for the development of technical specifications for the creation of automated process control systems

VRD 39-1.10-006-2000*: Rules for the technical operation of gas pipelines

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English
Price: $283.00
imgalt
Clear sheet glass. Specifications
Language: English
Price: $250.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!