GOST R ISO 6157-1-2009
ГОСТ Р ИСО 6157-1-2009
|
|
Fasteners. Surface discontinuities. Part 1. Bolts, screws and studs for general requirements
Изделия крепежные. Дефекты поверхности. Часть 1. Болты, винты и шпильки общего назначения
Status: Not effective - Canceled. Registration information 690-st dated 06/27/2016 (official website of Rosstandart); IUS 1-2017
1.1 This standard establishes permissible limit values for various types of defects in the surface of bolts, screws and studs for general use: - with a nominal thread diameter of at least 5 mm; - accuracy classes A and B; - strength classes up to 10.9 inclusive, unless otherwise defined by the relevant product standards or by agreement between the manufacturer and the customer. 1.2. The allowable limit values for surface defects for bolts, screws and studs for special purposes (for example, for automatic assembly) are specified in ISO 6157-3. For defects in the surfaces of bolts, screws and studs for engineering purposes, it is necessary to conduct a more thorough inspection, which is determined by the relevant product standards, or the customer must determine the allowable acceptance limits in the application and upon the purchase order. 1.3 For products in which acceptable surface defects are found, given in Clause 3, the requirements for the minimum values of mechanical and functional properties specified in ISO 898-1 shall be met.
1.1 Настоящий стандарт устанавливает допустимые предельные значения для различных типов дефектов поверхности болтов, винтов и шпилек общего назначения: - с номинальным диаметром резьбы не менее 5 мм; - классов точности A и B; - классов прочности до 10.9 включительно, если иначе не определено соответствующими стандартами на продукцию или соглашением между изготовителем и заказчиком. 1.2 Допустимые предельные значения дефектов поверхности болтов, винтов и шпилек специального назначения (например, для автоматической сборки) установлены в ИСО 6157-3. Для дефектов поверхностей болтов, винтов и шпилек машиностроительного назначения необходимо проводить более тщательный контроль, который определен соответствующими стандартами на продукцию, или заказчик должен сам определить допустимые пределы приемки в заявке и при заказе на поставку. 1.3 Для изделий, в которых обнаружены допустимые дефекты поверхности, приведенные в разделе 3, должны выполняться требования к минимальным значениям механических и функциональных свойств, указанных в ИСО 898-1
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/10/2009
SKU: RUSS63311
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
21 Mechanical systems and general purpose devices »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
Standards for pipe fittings (TPA) »
13. Standards for basic components and parts of injection molding machines »
13.2 Fasteners »
ISO classifier »
21 MECHANICAL SYSTEMS AND GENERAL PURPOSE DEVICES »
21.060 Fasteners »
21.060.10 Bolts, screws, studs »
National standards »
21 MECHANICAL SYSTEMS AND GENERAL PURPOSE DEVICES »
21.060 Fasteners »
21.060.10 Bolts, screws, studs »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G3 Fasteners for general engineering applications »
G32 Screws. Studs »
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 52627-2006: Bolts, screws and studs. Mechanical properties and test methods
GOST R ISO 3269-2009: Fasteners. Acceptance inspection
The Document is Referenced By:
GOST 11530-2014: Rail joint bolts. Specifications
GOST 16016-2014: Clamp bolts for rail track fastenings. Specifications
GOST 16017-2014: Inserted bolts for rail track fastenings. Specifications
GOST 22032-76: Studs with threaded end of 1d. Product grade B. Construction and dimensions
GOST 24379.0-2012: Foundation bolts. General specifications
GOST 32484.3-2013: High-strength structural bolting assemblies for preloading. System HR - Hexagon bolt and nut assemblies
GOST 32484.4-2013: High-strength structural bolting assemblies for preloading. System HV - Hexagon bolt and nut assemblies
GOST ISO 4162-2014: Hexagonal bolts with reduced head with flange. Precision class A to class of precision B
GOST ISO 7380-1-2014: Round head screw. Part 1. Round head screw with hexagon socket
GOST ISO 7380-2-2014: Round head screw. Part 2. Round head screw with hexagon socket and rim
GOST ISO 898-5-2014: Mechanical properties of fasteners made of carbon and alloyed steels. Part 5. Setting screws and similar threaded fasteners of established classes of hardness with large and small thread pitch
GOST R 52643-2006: High-strength screws and nuts washers for metal structures. General specifications
GOST R 52644-2006: Hexagon bolts for high-strength structural bolting with large width across flats. Specifications.
GOST R 53664-2009: High-strength cheese-head and conical bolts for bridge building. Nuts and washers for them. Specifications
GOST R 53682-2009: Fired heaters for refineries. General technical requirements
GOST R 53819-2010: Vehicles. Fastenings wheels. Technical requirements and test methods
GOST R 54786-2011: Fastening parts for detachable connections of nuclear power plants. Specifications.
GOST R 55738-2013: Studs and ceramic ferrules for stud welding
GOST R 58249-2018: Machines for planting, harvesting, post-harvest processing of potatoes. Technical requirements
GOST R ISO 10642-2012: Hexagon socket countersunk head screws
GOST R ISO 1207-2013: Slotted cheese head screws. Product grade A
GOST R ISO 12474-2012: Hexagon socket head cap screws with metric fine pitch thread
GOST R ISO 14580-2012: Hexalobular socket cheese head screws
GOST R ISO 14584-2012: Star type socket raised countersunk head screws
GOST R ISO 1580-2013: Slotted pan head screws. Product grade A
GOST R ISO 2009-2013: Slotted raised countersunk head screws. Product grade A
GOST R ISO 2010-2013: Slotted raised countersunk head screws. Product grade A
GOST R ISO 3269-2009: Fasteners. Acceptance inspection
GOST R ISO 4014-2013: Hexagon head bolts. Product grades A and B
GOST R ISO 4017-2013: Hexagon head screws. Product grades A and B
GOST R ISO 4026-2013: Hexagon socket set screws with flat point
GOST R ISO 4027-2013: Hexagon socket set screws with cone point
GOST R ISO 4028-2013: Hexagon socket set screws with dog point
GOST R ISO 4029-2013: Hexagon socket set screws with cup point
GOST R ISO 4762-2012: Hexagon socket head screws
GOST R ISO 4766-2013: Slotted set screws with flat point
GOST R ISO 7045-2013: Pan head screws with type H or type Z cross recess. Product grade A
GOST R ISO 7046-1-2013: Countersunk flat head screws (common head style) with type H or type Z cross recess. Product grade A. Part 1. Steel screws of property class 4.8
GOST R ISO 7046-2-2013: Countersunk flat head screws (common head style) with type H or type Z cross recess. Product grade A. Part 2. Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws
GOST R ISO 7047-2013: Raised countersunk head screws with type H or type Z cross recess. Product grade A
GOST R ISO 7048-2013: Cross-recessed cheese head screws
GOST R ISO 8676-2013: Hexagon head screws with metric fine pitch thread. Product grades A and B
GOST R ISO 8765-2013: Hexagon head bolts with metric fine pitch thread. Product grades A and B
GOST R ISO 898-1-2011: Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1. Bolts, screws and studs of specified property classes with coarse thread and fine pitch thread
GOST R ISO 8992-2011: Fasteners. General requirements for bolts, screws, studs and nuts
ST TsKBA 037-2006: Pipe fittings. Packing glands. Construction, main dimensions and technical requirements
|
Customers Who Viewed This Item Also Viewed:
 |
Liquid lubricating and plastic materials. Method of test for lubricating properties on four ball machine
Language: English |
Armour clothes. Classification and general technical requirements
Language: English |
Food products. Methods for detection and quantity determination of coliformes
Language: English |
Natural gas. Methods of calculation of physical properties. Calculation of physical properties on base information on density of standards conditions and nitrogen and carbon dioxide contents
Language: English |
Hotels design
Language: English |
Railroad rails. General specifications
Language: English |
Potassium chloride
Language: English |
Controllers acting without
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
