GOST R 55374-2012

ГОСТ Р 55374-2012

Alloyed structural rolled steel for bridge building. General specifications

Прокат из стали конструкционной легированной для мостостроения. Общие технические условия

Status: Effective - Introduced for the first time. IUS 1-2014

This standard applies to hot-rolled steel plates, broadband universal, structural and long products from structural alloyed steel, intended for the manufacture of steel structures of rail, road, combined, urban and pedestrian bridge structures operated in climatic zones corresponding to normal and northern execution, and in areas with an estimated seismicity of up to 9 points inclusive. This standard does not apply to movable bridge mechanisms. In terms of the norms of chemical composition and mechanical properties, this standard also applies to: - cold-formed profiles, made from rolled plates; - plate rolled steel grade 09G2SD, intended for the manufacture of the main layer of two-layer steel

Настоящий стандарт распространяется на горячекатаный толстолистовой, широкополосный универсальный, фасонный и сортовой прокат из конструкционной легированной стали, предназначенный для изготовления стальных конструкций железнодорожных, автодорожных, совмещенных, городских и пешеходных мостовых сооружений, эксплуатируемых в климатических зонах, соответствующих обычному и северному исполнению, и в районах с расчетной сейсмичностью до 9 баллов включительно. Настоящий стандарт не распространяется на механизмы разводных мостов. В части норм химического состава и механических свойств настоящий стандарт распространяется также на: - холодногнутые фасонные профили, изготовляемые из толстолистового проката; - толстолистовой прокат из стали марки 09Г2СД, предназначенный для изготовления основного слоя двухслойного проката

Choose Language: 
Format: Electronic (pdf/doc)
Page Count: 20

Approved: Federal Agency for Technical Regulation and Metrology, 12/27/2012

SKU: RUSS67034

Price: $138.57




The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 77 Metallurgy »

PromExpert » SECTION I. TECHNICAL REGULATION » V Testing and control » 4 Testing and control of products » 4.12 Testing and control of products of metallurgical industry » 4.12.4 Iron and steel products »

ISO classifier » 77 METALLURGY » 77.140 Iron and steel products » 77.140.50 Steel sheet products and semi-finished products »

National standards » 77 METALLURGY » 77.140 Iron and steel products » 77.140.50 Steel sheet products and semi-finished products »

ISO classifier » 77 METALLURGY » 77.140 Iron and steel products » 77.140.60 Steel bars and wire rod »

National standards » 77 METALLURGY » 77.140 Iron and steel products » 77.140.60 Steel bars and wire rod »

National Standards for KGS (State Standards Classification) » Latest edition » V Metals and metal products » V3 Steel quality and high quality (quality stock) » V32 Rolled and shaped steel »

National Standards for KGS (State Standards Classification) » Latest edition » V Metals and metal products » V3 Steel quality and high quality (quality stock) » V33 Sheets and Stripes »


The Document References:

GOST 10243-75: Steel. Methods of test and estimation of macrostructure

GOST 103-2006: Hot-rolled steel strips. Dimensions

GOST 103-41: Steel rolling strip. Range

GOST 12359-99: Carbon, alloyed and high-alloyed steels. Methods for determination of nitrogen

GOST 14019-2003: Metallic materials. Bend test method

GOST 14192-96: Cargo marking

GOST 1497-42: Metals. Tensile metal test methods

GOST 1497-84: Metals. Methods of tension test

GOST 18895-97: Steel. Method of photoelectric spectral analysis

GOST 19903-74: Hot-rolled steel sheets. Dimensions

GOST 21120-75: Round and rectangular bars and billets. Ultrasonic testing

GOST 22235-2010: Freight cars for 1520 mm gauge main line railways. General requirements for safety in loading-unloading and shunting operations

GOST 22536.0-87: Carbon steel and unalloyed cast iron. General requirements for methods of analysis

GOST 22536.10-88: Carbon steel and unalloyed cast iron. Methods for determination of alluminium

GOST 22536.11-87: Carbon steel and unalloyed cast iron. Methods for determination of titanium

GOST 22536.12-88: Carbon steel and unalloyed cast iron. Methods for determination of vanadium

GOST 22536.13-77: Carbon steel and unalloyed cast iron. Methods of spectral analysis

GOST 22536.14-88: Carbon steel and unalloyed cast iron. Methods for determination of zirconium

GOST 22536.1-88: Carbon steel and unalloyed cast iron. Methods for determination of general carbon and graphite

GOST 22536.2-87: Carbon steel and unalloyed cast iron. Methods for the determination of sulfur

GOST 22536.3-88: Carbon steel and unalloyed cast iron. Methods for determination of phosphorus

GOST 22536.4-88: Carbon steel and unalloyed cast iron. Methods for determination of silicon

GOST 22536.5-87: Carbon steel and unalloyed cast iron. Methods for determination of manganese

GOST 22536.6-88: Carbon steel and unalloyed cast iron. Methods for determination of arsenic

GOST 22536.7-88: Carbon steel and unalloyed cast iron. Methods for determination of chromium

GOST 22536.8-87: Carbon steel and unalloyed cast iron. Methods for determination of copper

GOST 22536.9-88: Carbon steel and unalloyed cast iron. Methods for determination of nickel

GOST 22727-88: Rolled sheet. Ultrasonic test methods

GOST 2590-2006: Round hot-rolled steel bars. Dimensions

GOST 2590-44: Hot rolled steel. Types and sizes

GOST 2591-2006: Square hot-rolled steel bars. Dimensions

GOST 2591-44: Hot-rolled steel square. Types and sizes

GOST 26020-83: Hot-rolled steel I-beam with parallel flange edges. Dimensions.

GOST 26877-2008: Metal products. Methods of measuring form variations

GOST 27809-95: Cast iron and steel. Methods of spectrographic analysis

GOST 28473-90: Iron, steel, ferroalloys, metal chromium and metal manganese. General requirements for methods of analysis

GOST 2879-2006: Hexagonal hot-rolled steel bars. Dimensions

GOST 2879-45: Hot-rolled hexagon steel. Assortment

GOST 28870-90: Steel. Methods tensile tests of rolled thick-plates in the thickness direction

GOST 30456-97: Metal production. Rolled steel and tubes. Methods of blow bending tests

GOST 535-2005: Common quality carbon steel bar and shaped sections. General specifications

GOST 535-45: Carbon steel, hot-rolled, of ordinary quality, sorted. Specification

GOST 7268-82: Steel. Method for determination of ability to mechanical aging by impact bend testing

GOST 7564-97: Rolled products general rules of samples, rough specimens and test pieces selection for mechanical and technological testing

GOST 7565-81: Iron, steel and alloys. Sampling for determination of chemical composition

GOST 7566-94: Metal products

GOST 8239-89: Steel hot-rolled I-beams

GOST 8240-97: Hot-rolled steel channels. Assortment

GOST 82-41: Wide-flat universal rolled steel. Assortment

GOST 82-70: Universal hot-rolled steel wide strips. Dimensions

GOST 8509-93: Hot-rolled steel equal-leg angles. Dimensions

GOST 8510-86: Hot-rolled steel unequal-leg angles. Dimensions

GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature

GOST R 1.0-2012: Standardization in the Russian Federation. Basic provisions

GOST R 50424-92: Steel and iron. Method for determination of calcium

GOST R 53845-2010: Steel rolled products. General rules of sampling, rough specimens and test pieces selection for mechanical and technological testing

GOST R 54153-2010: Steel. Method of atomic emission spectral analysis

The Document is Referenced By:

ODM 218.2.090-2017: Guidelines for the use of tubular welded grooves in the construction of roads

ODM 218.3.103-2018: Recommendations for the use of screw piles on roads

PNST 309-2018: Roads are public. Bridges and pipes road. Technical requirements

PNST 353-2019: General automobile roads. Expansion joints with rubber compensator spans for road bridges. General specifications

SP 35.13330.2011: Bridges and pipes. Updated living edition of SNiP 2.05.03-84

SP 453.1325800.2019: Artificial high-speed railway lines. Design and construction rules

SP 494.1325800.2020: Spatial metallic coatings. Design rules

Customers Who Viewed This Item Also Viewed:

Rules of Electrical Installations Design (Russian Electrical Code). 7th Edition. All sections and exhibits
Language: English
Price: $478.76
Foundation bolts. Structure and dimensions
Language: English
Price: $198.99
Hot-rolled sheet. Range
Language: English
Price: $72.27
Pipeline valves. Leakage rates of valves
Language: English
Price: $173.25
Flanges for valves, fittings and pipelines for pressure to PN 250. Design, dimensions and general technical requirements
Language: English
Price: $293.04
Stainless steels and corrosion resisting, heat-resisting and creep resisting alloys. Grades
Language: English
Price: $212.85
Electromagnetic compatibility of multimedia equipment. Emission requirements
Language: English
Price: $974.64
Non-destructive testing. Method of magnetic particle testing. Standard technological processes
Language: English
Price: $292.05
Supports for Cylindrical and Conical Upright Apparatus. Types and Basic Parameters
Language: English
Price: $573.20
Rolling stock of railways. Springs cylindrical screw. Certification requirements
Language: English
Price: $175.65
Steel structures
Language: English
Price: $297.00
Metal products from structural alloy steel. Specification
Language: English
Price: $371.25
Obosnovanie bezopasnosti oborudovaniya. Rekomendatsii po podgotovke
Language: English
Price: $67.32
Reinforcing rolled products for reinforced concrete constructions. Specifications
Language: English
Price: $298.98
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $108.90
State system for ensuring the uniformity of measurements. Verification of testing equipment. General principles
Language: English
Price: $121.77
Steel building structures. General specifications
Language: English
Price: $250.17
Fencing constructions for translucent buildings and structures. Design rules
Language: English
Price: $609.15
Tests on electric and optical cables under fire conditions. Part 3-22. Flame spread of vertically-mounted bunched wires or cables. Category A
Language: English
Price: $102.96
Hexagon head bolts. Product grades A and B
Language: English
Price: $203.94

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!