GOST R 54960-2012
ГОСТ Р 54960-2012
|
|
Gas distribution systems. Block gas delivery stations. Cabinet gas delivery stations. General technical requirements
Системы газораспределительные. Пункты газорегуляторные блочные. Пункты редуцирования газа шкафные. Общие технические требования
Status: Not effective - Canceled. Registration information 281-st dated 04/13/2017 (Rosstandart official website); IUS 8-2017
This standard applies to block gas control points and cupboard gas reduction points designed to reduce the pressure of natural gas from an input value (up to 1.2 MPa inclusive) to the required values, as well as to perform the following functions: - automatically maintain a given output pressure regardless of the change gas flow and inlet pressure (in a given range of their values); - automatic cessation of gas supply when the output pressure rises or falls above or below the permissible target values; - gas cleaning from mechanical impurities; - gas metering. This standard establishes general technical requirements for gas reduction points intended for use in gas distribution networks during the transportation of combustible gases according to GOST 5542, used as fuel for industrial and household purposes. This standard does not apply to gas control installations, stationary gas control points, as well as to gas reduction points taken into operation before the day of entry into force of this standard.
Настоящий стандарт распространяется на блочные газорегуляторные пункты и шкафные пункты редуцирования газа, предназначенные для редуцирования давления природного газа с входного значения (до 1,2 МПа включительно) до требуемых значений, а также для выполнения следующих функций: - автоматического поддержания заданного выходного давления независимо от изменения расхода и входного давления газа (в заданном диапазоне их значений); - автоматического прекращения подачи газа при повышении или понижении выходного давления сверх или ниже допустимых заданных значений; - очистки газа от механических примесей; - учета газа. Настоящий стандарт устанавливает общие технические требования к пунктам редуцирования газа, предназначенным для применения в сетях газораспределения при транспортировании горючих газов по ГОСТ 5542, используемых в качестве топлива для промышленного и коммунально-бытового назначения. Настоящий стандарт не распространяется на газорегуляторные установки, стационарные газорегуляторные пункты, а также на пункты редуцирования газа, принятые в эксплуатацию до дня вступления в силу настоящего стандарта
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
8/22/2012
SKU: RUSS67866
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
75 Extraction and processing of oil, gas and related production »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.180 Equipment for oil and gas industry »
75.180.99 Other equipment for oil and gas industry »
National standards »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.180 Equipment for oil and gas industry »
75.180.99 Other equipment for oil and gas industry »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G4 Machinery and equipment for heavy industry »
G43 Machines and equipment for oil producing, oil refining and gas industry »
The Document References:
GOST 5264-80: Manual arc welding. Welding joints. Main types, design elements and dimensions
GOST 10549-80: Screw thread runout. Washout threads, total thread runouts, undercuts and chamfers
GOST 11534-75: Hand arc welding. Acute and blunt weld joints. Main types, design elements and dimensions
GOST 11881-76: Controllers acting without
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.1.010-76: Explosion safety. General requirements
GOST 12.2.003-91: Industrial equipment. General safety requirements
GOST 12815-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). Types. Connecting dimensions and dimensions of sealing surfaces
GOST 12816-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). General technical requirements
GOST 12817-80: Cast grey iron flanges for Pnom from 0,1 to 1,6 MPa (from 1 to 16 kgf/sq sm). Design and dimensions
GOST 12818-80: Cast malleable iron flanges for Pnom from 1,6 to 4,0 MPa (from 16 to 40 kgf/cm2). Design and dimensions
GOST 12819-80: Cast steel flanges for Pnom from 1,6 to 20,0 MPa (from 16 to 200 kgf/sq sm). Design and dimensions
GOST 12820-80: Steel plane welded flanges for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/cm2). Design and dimensions
GOST 12821-80: Steel butt-welded flanges for Pnom from 0,1 to 20,0 MPa (from 1 to 200 kgf/cm2). Design and dimensions
GOST 12822-80: Steel loose flanges with welded ring for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/sq sm). Design and dimensions
GOST 14192-96: Cargo marking
GOST 14776-79: Arc welding. Button welds. Main types, design elements and dimensions
GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods
GOST 15.309-98: System of product development and launching into manufacture. Test and acceptance of produced goods. Principal positions
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage
GOST 16037-80: Welded joints in steel pipelines. Main types, design elements and dimensions
GOST 16093-2004: Basic norms of interchangeability. Metric screw thread. Tolerances. Clearance fits
GOST 17375-2001: Carbon and low-alloy steel butt-welding fittings. Sharply curved bends type 3D (R=1,5 DN). Design
GOST 17376-2001: Carbon and low-alloy steel butt-welding fittings. Tees. Design
GOST 17378-2001: Carbon and low-alloy steel butt-welding fittings. Reducers. Design
GOST 17379-2001: Carbon and low-alloy steel butt-welding fittings. Elliptical caps. Design
GOST 17380-2001: Carbon and low-alloy steel butt-welding fittings. General specifications
GOST 21130-75: Electrical articles. Grounding terminals and grounding signs
GOST 24597-81: Unitized tared and piece goods cargoes. Main parameters and dimensions
GOST 24705-2004: Вasic norms of interchangeability. Metric screw thread. Basic dimensions
GOST 30753-2001: Carbon and low-alloy steel butt-weldings fittings. Sharply curved bends type 2D (R=DN). Design
GOST 5542-87: Natural fuel gases for industrial and domestic use
GOST 6357-81: Basic norms of interchangeability pipe cylindrical thread
GOST 6527-68: Female ends with pipe cylindrical thread. Dimensions
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 8969-75: Pipe steel connections with cylindrical thread for pipelines P=1,6 МPа. Adapter couplings. Basic dimensions
GOST 9150-2002: Basic norms of interchangeability. Metric screw threads. Profile
GOST 9544-2005: Pipeline gate valves. Classes and rates of gates sealibility
GOST R 12.1.019-2009: Occupational safety standards system. Electrical safety. General requirements and nomenclature of kinds of protection
GOST R 50571.29-2009: Electrical installations of buildings. Part 5-55. Selection and erection of electrical equipment. Other equipment
GOST R 50571.3-2009: Low-voltage electrical installations. Part 4-41. Requirements for safety ensuring. Protection against electric shock
GOST R 51330.0-99: Explosionproof electrical apparatus. Part 0. General requirements
GOST R 51350-99: Safety requirements for electrical equipment for measurement, control, and laboratory use. Part 1. General requirements
GOST R 52350.14-2006: Electrical apparatus for explosive gas atmospheres. Part 14. Electrical installations in hazardous areas (other than mines)
GOST R 52750-2007: Panic and emergency exit devices. Specifications
GOST R 52760-2007: Pipeline valves. Requirements for the marking and distinctive painting
GOST R 53672-2009: Pipeline valves. General safety requirements
GOST R 54808-2011: Pipeline valves. Leakage rates of valves.
SNiP 41-02-2003: Heat networks
SP 42-102-2004: Design and construction of gas pipelines from metal pipes. To replace SP 42-102-96
SP 5.13130.2009: Fire protection systems. Automated fire alarm and fire extinguishing installations. Design norms and regulations
The Document is Referenced By:
GOST R 55472-2013: Gas distribution systems. Requirements for gas distribution networks. Part 0. General
GOST R 56019-2014: Gas distribution systems. Gas pressure regulating stations. Functional requirements
Order 498: List of questions proposed in the qualification examination for certification of experts in the field of industrial safety
Order 5214: The list of documents in the field of standardization, the application of which on a voluntary basis to ensure compliance with the requirements of application and execution of the Government of the Russian Federation of October 29, 2010 № 870 "On approval of technical regulations on the safety of gas distribution and gas consumption networks" (as amended on June 23, 2011) and implementation of conformity assessment
Order 5214: On approval of the List of documents in the field of standardization, the application of which on a voluntary basis to ensure compliance with the requirements of technical regulations "On safety of gas distribution and gas consumption networks" approved by the Government of the Russian Federation on October 29, 2010 N 870 (as amended on April 22, 2013) (lost force from 01.04.2022 on the order of Rosstandart from 10.01.2022 N 3)
SP 253.1325800.2016: High-rise buildings utilities
SP 267.1325800.2016: High rise buildings and complexes. Design rules
Customers Who Viewed This Item Also Viewed:
 |
Building materials. Methods for combustibility test
Language: English |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Building materials spread flame test method
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.