GOST R 53682-2009
ГОСТ Р 53682-2009
|
|
Fired heaters for refineries. General technical requirements
Установки нагревательные для нефтеперерабатывающих заводов. Общие технические требования
Status: Effective - Introduced for the first time. IUS 4-2011
This standard applies to heating installations for oil refineries in the oil, oil refining, petrochemical and gas industries operating at a coil pipe wall temperature of up to 760 ° C. This standard establishes the minimum technical requirements for the design, materials, manufacture, acceptance, testing, preparation for shipment and installation of fire heaters and general-purpose burners for oil refining. This standard does not apply to steam reforming furnaces and pyrolysis furnaces. In addition to the requirements of this standard, you should follow the rules and regulations on industrial safety.
Настоящий стандарт распространяется на нагревательные установки для нефтеперерабатывающих заводов нефтяной, нефтеперерабатывающей, нефтехимической и газовой промышленности, работающие при температуре стенки трубы змеевика до 760 °С. Настоящий стандарт устанавливает минимальные технические требования к проектированию, материалам, изготовлению, приемке, испытанию, подготовке к отправке и монтажной сборке огневых нагревателей и горелок общего назначения для нефтепереработки. Настоящий стандарт не распространяется на печи парового риформинга и печи пиролиза. В дополнение к требованиям настоящего стандарта следует руководствоваться нормами и правилами по промышленной безопасности
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/15/2009
SKU: RUSS69496
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
75 Extraction and processing of oil, gas and related production »
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Metal structures »
Welding regulations »
Welding materials »
Welding regulations »
welding equipment »
Welding regulations »
Admission Testing »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Welding work »
Automatic welding »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Welding materials »
Wire »
Welding regulations »
Welding materials »
Gases »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
032/2013 TR CU. On safety of overpressure equipment »
Regulations and standards (to 032/2013 TR CU) »
ISO classifier »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
National standards »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
ISO classifier »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
71.120.01 Equipment for chemical industry as a whole »
National standards »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
71.120.01 Equipment for chemical industry as a whole »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
National standards »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
75.200.01 Transportation and storage in general »
National standards »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.200 Equipment for oil refining, oil products and natural gas »
75.200.01 Transportation and storage in general »
As a Replacement Of:
RD 3688-00220302-003-04: The leading document. Pipe heating furnaces. Requirements to design, production and operation.
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications
GOST 12.1.003-83: Noise. General safety requirements
GOST 12865-67: Expanded vermiculits.
GOST 1759.0-87: Bolts, screws, studs and nuts. Specifications.
GOST 1759.1-82: Bolts, screws, studs and nuts. Tolerance, monitoring methods of dimensions and deviations of shape and surface orientation
GOST 1759.2-82: Bolts, screws, and studs. Surface imperfections and monitoring methods
GOST 1759.3-83: Nuts. Surface defects and methods of control
GOST 1759.4-87: Bolts, screws and studs. Mechanical properties and test methods
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 2.601-2013: Unified system for design documentation. Exploitative documents
GOST 20072-74: Heat-resistant steel
GOST 20415-82: Non-destructive testing. Acoustic methods. General principles
GOST 20910-90: Refractory concretes. Specifications
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 21204-97: Industrial gas burners. General technical requirements
GOST 23619-79: Refractory heat-insulating mullite-silica glass-fibrous materials and products. Specifications
GOST 23732-2011: Water for concretes and cement mortars Technical specifications.
GOST 23829-85: Acoustical non-destructive testing. Terms and definitions
GOST 24522-80: Capillary non-destructive inspection. Terms and definitions
GOST 27824-2000: Industrial burners for liquid fuel. General technical requirements
GOST 3242-79: Welded joints
GOST 380-2005: Common quality carbon steel. Grades
GOST 390-96: Fireclay and semiacidic refractory articles general-purpose and mass production. Specifications
GOST 4543-71: Structural alloyed steel
GOST 535-2005: Common quality carbon steel bar and shaped sections. General specifications
GOST 550-75: Seamless steel tubes for petroleum processing and petrochemical industry. Specifications
GOST 5632-72: High-alloy steels and corrosion-proof, heat-resisting and heat treated alloys. Grades
GOST 7350-77: Plate, corrosion-resistant, heat-resistant, and high-temperature steel
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 8479-70: Structural carbon and alloy steel forgings
GOST 8691-73: General-purpose refractory articles. Form and dimensions
GOST 8731-74: Seamless hot-deformed steel pipes. Specifications
GOST 8733-74: Cold-formed and heat-formed seamless steel pipes. Technical requirements
GOST 9.402-2004: Unified system of corrosion and ageing protection. Paint coatings. Metal surface preparation for painting
GOST 9757-90: Artificial porous gravel, crushed stone and sand artificially produced expanded/foamed gravel, crushed rock and sand]. Specifications
GOST 977-88: Steel castings. General specifications
GOST 9940-81: Seamless hot-deformed tubes made from corrosion-resistant steel
GOST 9941-81: Seamless cold- and warm-deformed tubes made from corrosion-resistant steel
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 1.0-2012: Standardization in the Russian Federation. Basic provisions
GOST R 53383-2009: Hot-deformed seamless steel pipes. Specifications
GOST R 54159-2010: Seamless and welded cold deformed steel pipes for general purposes. Specifications
GOST R 54808-2011: Pipeline valves. Leakage rates of valves.
GOST R 55724-2013: Non-destructive Testing. Welded Joints. Ultrasonic Methods
GOST R 55776-2013: Radiation non-destructive inspection. Terms and definitions
GOST R ISO 4161-2013: Hexagon nuts with flange, style 2. Coarse thread
GOST R ISO 4759-1-2009: Tolerances for fasteners. Part 1: bolts, screws, studs and nuts. Product grades A, B and C
GOST R ISO 6157-1-2009: Fasteners. Surface discontinuities. Part 1. Bolts, screws and studs for general requirements
GOST R ISO 6157-2-2009: Fasteners - Surface discontinuities - Part 2: Nuts
GOST R ISO 898-1-2011: Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1. Bolts, screws and studs of specified property classes with coarse thread and fine pitch thread
Order 96: Federal norms and rules in the field of industrial safety "General rules of explosion safety for explosion and fire hazardous chemical, petrochemical and oil refining industries"
PB 09-563-03: Industrial Safety Regulations for Refinery Plants
RD 26-02-80-2004: The leading document. Welded coils for pipe furnaces. Requirements to design, production and delivery.
RTM 26-02-67-84: Method of strength design of furnace elements working under pressure
Safety Guide: Recommendations on arrangement and safe operation of process pipelines
Safety Guide: Recommendations on technical diagnostics of welded vertical cylindrical tanks for oil and petroleum products
TU 14-3-1128-2000: Seamless hot-deformed steel pipes for gas pipelines of gas-lift systems and gas field equipment. Technical conditions
TU 14-3R-55-2001: Seamless steel pipes for steam boilers and pipelines
VUPP-88: Departmental instructions for the fire-prevention design of enterprises, buildings and structures of the oil refining and petrochemical industry
The Document is Referenced By:
Decision 96: On the list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis to ensure compliance with the requirements of technical regulations of the Customs Union "On safety of equipment operating under excess pressure" (TR TS 032/2013), and the list of international and regional (interstate) standards, and in their absence - national (state) standards, containing rules and methods of research (tests) and
SP 157.1328500.2014: Rules for technological design of refineries and petrochemical complexes
|
Customers Who Viewed This Item Also Viewed:
 |
Preservative oil K-17
Language: English |
Jet fuels
Language: English |
Chill moulds. Ventilation channels. Dimensions
Language: English |
Additive АКОР-1. Specifications
Language: English |
Vibration. Evaluation of machine vibration by measurements on non-rotating parts. Part 3. Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15000 r/min
Language: English |
Ceramic brick and stone. General specifications
Language: English |
Microbiology of food and animal feeding stuffs. Methods for detection and enumeration of sulphite-reducing bacteria growing under anaerobic conditions
Language: English |
Maximum admissible amounts of chemical substances, emitting from the packaging materials into food products
Language: English |
System of design documents for construction. Rules for execution of the working documentation of architectural and construction solutions
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.