GOST R 54772-2011
ГОСТ Р 54772-2011
|
|
Supple mining main vents and shaped components for them. General technical requirements and test methods
Трубы вентиляционные гибкие шахтные и фасонные части к ним. Общие технические требования и методы испытаний
Status: Effective - Introduced for the first time. IUS 10-2012
This standard applies to flat (smooth), spiral and reinforced flexible ventilation shaft pipes and fittings to them from tubular materials based on artificial leather with their welding connected, for air transportation in ventilation systems of dead-end workings of mining enterprises and underground construction in the following conditions: - coal mines and mines, including hazardous gas and / or dust; - relative humidity of air at a temperature of 25 degrees. With up to 98%; - ambient temperature from + 40 degrees. C to minus 20 degrees. C. This standard establishes the basic indicators and test methods for ventilation flexible shaft pipes.
Настоящий стандарт распространяется на плоские (гладкие), спиральные и армированные гибкие вентиляционные шахтные трубы и фасонные части к ним из трубных материалов на основе искусственных кож с соединением их сваркой, предназначенные для транспортирования воздуха в системах проветривания тупиковых выработок горно-добывающих предприятий и подземном строительстве в следующих условиях: - угольные шахты и рудники, включая опасные по газу и/или пыли; - относительная влажность воздуха при температуре 25 град. С до 98 %; - температура окружающей среды от плюс 40 град. С до минус 20 град. С. Настоящий стандарт устанавливает основные показатели и методы испытаний вентиляционных гибких шахтных труб
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/13/2011
SKU: RUSS70023
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
73 Mining and minerals »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.13 Testing and control of products of engineering industry »
4.13.2 Machines and equipment for special purposes »
4.13.2.4 Machines and equipment for mining, oil industry and quarrying »
ISO classifier »
73 MINING AND MINERAL PRODUCTS »
73.100 Mining equipment »
73.100.20 Equipment for ventilation, air conditioning and lighting »
National standards »
73 MINING AND MINERAL PRODUCTS »
73.100 Mining equipment »
73.100.20 Equipment for ventilation, air conditioning and lighting »
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 10354-82: Polyethylene film Specifications
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.044-89: Fire and explosion hazard of substances and materials. Nomenclature of indices and methods of their determination
GOST 12.2.003-91: Industrial equipment. General safety requirements
GOST 12.4.152-85: Occupational safety standards system. Artificial leather. Methods for determining mould resistance
GOST 12302-83: Bags made of polymeric and composite materials. General specifications
GOST 14192-96: Cargo marking
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage
GOST 166-89: Vernier callipers. Specifications
GOST 17074-71: Artificial leather. Method for the determination of tear strength
GOST 17316-71: Artificial leather. Measuring method of tearing load and elongation of break
GOST 17317-71: Soft artificial leather. Method for determining the bond strength of a film coating with a substrate
GOST 17317-88: Artificial leather. Method for determination of interlayer bonding strength
GOST 17318-71: Artificial leather. Method of measuring of thermal sticking
GOST 1770-74: Laboratory volumetric glassware. Cylinders, beakers, measuring flasks, test tubes. General specifications
GOST 2.114-95: Unified system for design documentation. Specifications
GOST 2.601-2006: Unified system for design documentation. Exploitative documents
GOST 2405-88: Pressure gauges, vacuum gauges, pressure-vacuum gauges, pressure meters, draft gauges and draft-pressure gauges
GOST 24297-87: Input inspection of products. General provisions.
GOST 28498-90: Liquid-in-glass thermometers
GOST 29104.5-91: Industrial fabrics. Methods for determination of test strength
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 5378-88: Vernier protractors. Specifications
GOST 6376-74: Hand anemometer accounting device. Specifications
GOST 7502-89: Measuring metal tapes. Specifications
GOST 7502-98: Measuring metal tapes. Specifications
GOST 9.303-84: Unified system of corrosion and ageing protection. Metallic and non-metallic inorganic coatings. General requirements for selection
GOST 9389-75: Carbon steel spring wire
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 52274-2004: Static electricity spark safety. General technical requirements and test methods
GOST R 53228-2008: Non-automatic weighing instruments. Part 1. Metrological and technical requirements. Tests
GOST R 54772-2011: Supple mining main vents and shaped components for them. General technical requirements and test methods
GOST R EN 13463-1-2009: Non-electrical equipment for potentially explosive atmospheres. Part 1. Basic method and requirements
PB 05-618-03: Coal Mine Safety Regulations
RD 03-423-01: Safety standards for conveyor belts for hazardous production facilities and test methods
The Document is Referenced By:
GOST R 54772-2011: Supple mining main vents and shaped components for them. General technical requirements and test methods
GOST R 57071-2016: Mining equipment. Regulations of safe use of machinery and mechanisms in coal mines and cut for the dust factor
Customers Who Viewed This Item Also Viewed:
 |
Building materials. Methods for combustibility test
Language: English |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Building materials spread flame test method
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.