GOST 18829-73
ГОСТ 18829-73
|
|
Rubber o-ring seals for hydraulic and pneumatic equipment. Specifications
Кольца резиновые уплотнительные круглого сечения для гидравлических и пневматических устройств. Технические условия
Status: Not effective - Superseded. Registration information 496-st dated 06.06.2017 (official website of Rosstandart); IUS 10-2017
The standard applies to rubber o-rings for hydraulic, fuel, lubricating and pneumatic devices designed to operate at temperatures from minus 60 to plus 200 degrees. C depending on the rubber group and under pressure: up to 50 MPa - in stationary compounds and up to 32 MPa - in mobile connections in mineral oils, liquid fuels, emulsions, lubricants, fresh and sea water; up to 40 MPa - in fixed joints and up to 10 MPa - in mobile joints in compressed air.
Стандарт распространяется на резиновые уплотнительные кольца круглого сечения для гидравлических, топливных, смазочных и пневматических устройств, предназначенные для работы при температуре от минус 60 до плюс 200 град. С в зависимости от группы резины и при давлении: до 50 МПа - в неподвижных соединениях и до 32 МПа - в подвижных соединениях в минеральных маслах, жидких топливах, эмульсиях, смазках, пресной и морскилй воде; до 40 МПа - в неподвижных соединениях и до 10 МПа - в подвижных соединениях в сжатом воздухе.
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
5/25/1973
SKU: RUSS70512
The Product is Contained in the Following Classifiers:
Evidence base (TR CU, Technical Regulation of the Customs Union) »
018/2011 TR CU. On safety of wheeled vehicles »
Regulations and standards (to 018/2011 TR CU) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.10 Testing and monitoring products of rubber and plastics industry »
4.10.1 Rubber products »
ISO classifier »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.50 Seals »
National standards »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.50 Seals »
National Standards for KGS (State Standards Classification) »
Latest edition »
L Chemical products and rubber-asbestos products »
L6 Rubber and asbestos products »
L63 Rubber technical products »
National Standards for OKSTU »
RUBBER AND ASBESTOS PRODUCTS »
Shaped products for seals »
The Document is Replaced With:
GOST 18829-2017: Rubber o-ring seals for hydraulic and pneumatic equipment. Specifications
The Document References:
GOST 11358-89: Dial-type thickness gauges and dial-type wall thickness gauges graduated in 0,01 and 0,1 mm. Specifications
GOST 12301-81: Cartons made from cardboard, paper
GOST 12433-83: Standard isooctanes. Specifications
GOST 13808-79: Rubber. Method for the determination of low temperature resistance according to elastic rebound after compression
GOST 14192-77: Marking of cargoes
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15152-69: Unified system of corrosion and ageing protection. Industrial rubber products for tropics. General requirements
GOST 16295-82: Packing anticorrosive paper. Specifications
GOST 19795-82: Measuring projectors
GOST 2.303-68: Unified system for design documentation. Lines
GOST 20363-88: Transparent drawing paper. Specifications
GOST 20403-75: Rubber. Method for determination hardness in international units (30 to 100 IRHD)
GOST 263-75: Rubber. Method for the determination of Shore A hardness
GOST 269-66: Rubber. General requirements for the physical mechanical tests
GOST 270-75: Rubber. Method of the determination elastic and tensile stress-strain properties
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 426-77: Rubber. Method for the determination of abrasion resistance under slipping
GOST 5789-78: Reagents. Toluene. Specifications
GOST 5959-80: Uncollapsable wooden sheet material boxes for weights to 200 kg mass. General specifications
GOST 8.051-81: State system for ensuring the uniformity measurements. Permissible errors of measurement of linear dimensions to 500 mm
GOST 892-89: Tracing paper. Specifications
GOST 9.024-74: Unified system of corrosion and ageing protection. Rubbers. Methods of heat ageing stability determination
GOST 9.029-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing of resistance to ageing under static deformation of compression
GOST 9.030-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing resistance to attack by corrosive media in limp state
GOST 9396-88: Boxes wooden reusable
GOST 9569-79: Paraffin paper
GOST 9833-73: Rubber toroidal sealing rings for hydraulic and pneumatic equipment. Construction and dimensions
The Document is Referenced By:
Decision 88: About the Program for the development (amendment, revision) of interstate standards, the application of which on a voluntary basis ensures compliance with the technical regulations of the Customs Union
GOST 11614-94: Semi-automatic flushing valves. Specifications
GOST 15763-2005: Threaded and flange pipe connections for PN to 63 MPa (to 630 kgf/sq sm). General specifications
GOST 15880-96: Electric drills. General specifications
GOST 18058-80: Three-phase asynchronous squirrel-cage submersible electric motors series ПЭД. Specifications
GOST 19535-74: Flange joints for hydraulic and lubricating systems. Specifications
GOST 19681-2016: Sanitary and technical water fittings. General specifications
GOST 19681-83: Water mixing and distribution accessories for sanitary and laboratory applications. General technical requirements
GOST 19681-94: Sanitary technical water mixing and distributing accessories. General specifications
GOST 25065-81: Fittings made on the thread. The ends of choke unions, screwed with a seal of rubber rings of round section and sockets for them. Design and dimensions
GOST 25065-90: Threaded pipe fittings. Screwed-in ends of case components sealed with rubber. O-rings and their sockets. Design
GOST 26340-84: Fittings made on the thread. The ends of the body parts, adjustable in direction, screw-in with sealing rubber rings of circular cross-section. Design and dimensions
GOST 28016-89: Threaded pipeline connections. Welded conical nipple. Construction
GOST 30852.1-2002: Explosionproof electrical equipment. Part 1. Flameproof enclusure type explosion protection
GOST 31.0151.01-90: Universal and special-purpose setters
GOST 31.121.42-84: Elements and assemblies of universal built-up and re-adjustable equipment for metal-cutting machines
GOST 32591-2013: Fittings of copper and copper alloys with compression ends for use with copper tubes. Specifications
GOST ISO 14310-2014: Oil and gas industry. Downhole equipment. The packers and bridge plugs. General specifications
GOST R 50073-92: Pipelines flange types joint fittings. Specifications
GOST R 51330.1-99: Electrical apparatus for explosive gas atmospheres. Part 1. Construction and verification test of flameproof enclosures of electrical apparatus
GOST R 52948-2008: Fittings from copper and copper alloys with compression ends for use with copper tubes. Specifications
GOST R 53820-2010: Motor vehicles. Details of sealing and protective. Technical requirements and test methods
GOST R 54482-2011: Piping connections for general-use hydraulic fluid power. Hose fittings with metric stud ends and O-ring. Technical requirements
GOST R 55735-2013: Mining equipment. High pressure mine rubber hoses with metallic tapings and metallic braidings with fitting. Safety requirements and test methods
GOST R 56629-2015: Electric Connectors for diving works. General specifications
GOST R ISO 17078-3-2013: Petroleum and natural gas industries. Drilling and production equipment. Part 3. Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels. General technical requirements
RD 22-207-88: Lifting machines. General requirements and production standards
RD 36-62-00: Hoisting equipment. General technical requirements.
TU 3645-002-16989527-99: PKN-03 Cutter for manual oxygen cutting
Customers Who Viewed This Item Also Viewed:
|
Controllers acting without
Language: English |
Building materials. Methods for combustibility test
Language: English |
Building materials spread flame test method
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Clear sheet glass. Specifications
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
|
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.