GOST R 52152-2003
ГОСТ Р 52152-2003
|
|
Long wall powered roof chocks. Basic parameters. General technical requirements. Test methods
Крепи механизированные для лав. Основные параметры. Общие технические требования. Методы испытаний
Status: Not effective - Canceled. Registration information 1089-st dated 11/22/2012
The standard applies to mechanized supports for lavas, designed for work in sewage treatment plants with narrow-grained combines or plow installations in lavas with a removable power from 0.8 to 6.0 m in one layer and tilt angles of 0 ° - 30 ° along the lava and 0 ° - 10 ° along the pole with the output power: - from 0.8 to 3.5 m inclusive - by the fall or uprising of the pole; - St. 3.5 to 6.0 m inclusive - by the dip of the reservoir. The standard establishes the nomenclature of quality indicators and their applicability, basic parameters and general technical requirements (including design, manufacturability, reliability, safety), hygienic and ergonomic requirements for materials, purchased products and fluids, as well as test methods for supports. The standard does not apply to complete lining and lining coal-mining units.
Стандарт распространяется на механизированные крепи для лав, предназначенные для работы в очистных комплексах с узкозахватными комбайнами или струговыми установками в лавах с вынимаемой мощностью от 0,8 до 6,0 м в один слой и углами наклона 0° - 30° вдоль лавы и 0° - 10° вдоль столба при вынимаемой мощности: - от 0,8 до 3,5 м включительно - по падению или восстанию столба; - св. 3,5 до 6,0 м включительно - по падению пласта. Стандарт устанавливает номенклатуру показателей качества и их применяемость, основные параметры и общие технические требования (в том числе к конструкции, технологичности, надежности, безопасности), гигиенические и эргономические требования к материалам, покупным изделиям и рабочим жидкостям, а также методы испытаний крепей. Стандарт не распространяется на комплектные крепи и крепи угледобывающих агрегатов.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstandart of Russia,
12/9/2003
SKU: RUSS70783
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
73 Mining and minerals »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.13 Testing and control of products of engineering industry »
4.13.2 Machines and equipment for special purposes »
4.13.2.4 Machines and equipment for mining, oil industry and quarrying »
ISO classifier »
73 MINING AND MINERAL PRODUCTS »
73.100 Mining equipment »
73.100.30 Equipment for drilling and excavation »
National standards »
73 MINING AND MINERAL PRODUCTS »
73.100 Mining equipment »
73.100.30 Equipment for drilling and excavation »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G4 Machinery and equipment for heavy industry »
G41 Exploration, mining and mineral processing equipment »
The Document References:
Federal Law 184-FZ: About technical regulation
GN 2.2.5.686-98: Maximum Allowable Concentrations (PDK) of Hazardous Substances in Workplace Air. Hygienic Standards
GOST 12.1.003-83: Noise. General safety requirements
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.2.003-91: Industrial equipment. General safety requirements
GOST 12.3.009-76: Occupational safety standards system. Loading and unloading works General safety requirements
GOST 15.309-98: System of product development and launching into manufacture. Test and acceptance of produced goods. Principal positions
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 16504-81: The state system of testing products. Product test and quality inspection. General terms and definitions
GOST 17108-86: Positive-displacement hydraulic drive and lubricating systems. Methods of parameters measurement
GOST 21753-76: Man -machine system control levers
GOST 22613-77: Man-machine system. Rotary switches and commutators. General ergonomic requirements
GOST 22614-77: «Man-machine» system. Key-actuated and push-button switches and commutators. General ergonomic requirements
GOST 24054-80: Engineering and instrument production items. Leak detection methods. General requirements
GOST 2405-88: Pressure gauges, vacuum gauges, pressure-vacuum gauges, pressure meters, draft gauges and draft-pressure gauges
GOST 9.032-74: Unified, system of corrosion and ageing protection. Paint coatings. Groups, technical requirements and designations
GOST 9.104-79: Unified system corrosion of corrosion and ageing protection. Paint coatings. Croups of operation conditions
GOST R 15.201-2000: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture
GOST R 8.568-97: State system for ensuring the uniformity of measurements. Verification of testing equipment. General principles
PB 05-618-03: Coal Mine Safety Regulations
PR 50.2.002-94: Procedure for Government Metrological Inspection of the Manufacturing, Condition, and Application of Measuring Devices Certified Using Measurement Procedures, Standards, and Compliance with Metrological Standards and Codes
PR 50.2.006-94: Procedure for calibration of measurement equipment
PR 50.2.009-94: The testing and approval procedure for the measurement instrumentation
The Document is Referenced By:
GOST R 54775-2011: Powered support pumping stations. General technical requirements. Test methods
GOST R 55157-2012: Mining equipment. Hydraulic jacks. General technical requirements and test methods
GOST R 55160-2012: Mining equipment. Mine face conveyers jacks. General technical requirements and test methods
GOST R 55729-2013: Mining equipment. Hydraulic props for roof of supports. General specifications
Customers Who Viewed This Item Also Viewed:
 |
Building materials. Methods for combustibility test
Language: English |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Building materials spread flame test method
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.