GOST 10362-76
ГОСТ 10362-76
|
|
Pressure hoses of vulcanized rubber with thread reinforcement and without end fitting. Specifications
Рукава резиновые напорные с нитяным усилением, неармированные. Технические условия
Status: Not effective - Superseded. Registration information 546-st dated 06/15/2017 (Rosstandart official website); IUS 10-2017
The standard applies to pressure rubber hoses unreinforced with thread reinforcement used as flexible pipelines for supplying air, inert gases and liquids under pressure, operating in areas with a temperate and tropical climate at temperatures from minus 50 to plus 90 ° С, in areas with cold a climate at a temperature from minus 60 to plus 90 ° C. The standard does not apply to hoses for gas welding and cutting metals, power hydraulic system of combine harvesters, food industry and diving equipment.
Стандарт распространяется на напорные резиновые рукава неармированные с нитяным усилением, применяемые в качестве гибких трубопроводов для подачи под давлением воздуха, инертных газов и жидкостей, работоспособные в районах с умеренным и тропическим климатом при температуре от минус 50 до плюс 90 °С, в районах с холодным климатом при температуре от минус 60 до плюс 90 °С. Стандарт не распространяется на рукава для газовой сварки и резки металлов, силовой гидравлической системы зерноуборочных комбайнов, пищевой промышленности и водолазной техники.
Choose Language:
Format: Electronic (pdf/doc)
Approved: USSR State Committee for Standards,
6/14/1976
SKU: RUSS70939
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
83 Rubber, technical rubber, asbestos and plastic industries »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
018/2011 TR CU. On safety of wheeled vehicles »
Regulations and standards (to 018/2011 TR CU) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.10 Testing and monitoring products of rubber and plastics industry »
4.10.1 Rubber products »
ISO classifier »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.40 Sleeves »
National standards »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.40 Sleeves »
National Standards for KGS (State Standards Classification) »
Latest edition »
L Chemical products and rubber-asbestos products »
L6 Rubber and asbestos products »
L63 Rubber technical products »
National Standards for OKSTU »
RUBBER AND ASBESTOS PRODUCTS »
Sleeves »
The Document is Replaced With:
GOST 10362-2017: Pressure rubber hoses with thread reinforcement without end fittings. Technical conditions
As a Replacement Of:
GOST 10362-63: Hoses of rubber, pressured, with thread braiding
The Document References:
GOST 1012-72: Aviation petrol
GOST 10227-86: Jet fuels
GOST 1033-79: Fatty cup grease. Specifications
GOST 14192-96: Cargo marking
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15152-69: Unified system of corrosion and ageing protection. Industrial rubber products for tropics. General requirements
GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage
GOST 166-89: Vernier callipers. Specifications
GOST 2.124-85: Sequence of application of purchased products
GOST 2084-77: Mobile gasoline Specifications
GOST 2405-88: Pressure gauges, vacuum gauges, pressure-vacuum gauges, pressure meters, draft gauges and draft-pressure gauges
GOST 263-75: Rubber. Method for the determination of Shore A hardness
GOST 269-66: Rubber. General requirements for the physical mechanical tests
GOST 270-75: Rubber. Method of the determination elastic and tensile stress-strain properties
GOST 28084-89: Low-freezing cooling liquids. General specifications.
GOST 2930-62: Measuring instruments. Characters and signs
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 305-82: Diesel fuel. Specifications
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 5378-88: Vernier protractors. Specifications
GOST 6768-75: Rubber and rubberized fabric. Method for determination of the bond strength at ply separation
GOST 7502-89: Measuring metal tapes. Specifications
GOST 7502-98: Measuring metal tapes. Specifications
GOST 9.024-74: Unified system of corrosion and ageing protection. Rubbers. Methods of heat ageing stability determination
GOST 9.026-74: Unified system of corrosion and ageing protection. Vulcanized rubber. Method of accelerated determination to ozone and thermolightozone resistance
GOST 9.030-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing resistance to attack by corrosive media in limp state
GOST R 51105-97: Gasoline for combustion engines. Unleaded gasoline. Specifications
The Document is Referenced By:
Decision 88: About the Program for the development (amendment, revision) of interstate standards, the application of which on a voluntary basis ensures compliance with the technical regulations of the Customs Union
GOST 30154-94: Domestic gas ranges for tourists. General specifications
GOST 31562-2012: Рneumatic rock drills. General technical requirements
GOST 31563-2012: Pneumatic hammer drills. Technical requirements and testing methods
GOST 31564-2012: Pneumatic stopper drills. General technical requirements
GOST R 51246-99: Pneumatic hammer drills. Technical requirements and testing methods
GOST R 52442-2005: Pneumatic stopper drills. General technical requirements
GOST R 52443-2005: Pneumatic rock drills. General technical requirements
GOST R 53834-2010: Vehicles. Hoses for hydraulic systems. Technical requirements and test methods
Guideline 424: Guidelines for the construction of line structures for backbone and intra-zone cable communication lines (Sections 15-23. Appendices 1-11)
Guideline 424: Guidelines for the construction of line structures for backbone and intra-zone cable communication lines
RD 153-34.0-04.185-2003: Machines and equipment for construction, technical re-equipment and repair of energy facilities. Requirements for design, materials, manufacturing, acceptance and testing
RD 22-207-88: Lifting machines. General requirements and production standards
RM 2970: Device for damping the speed of the fall of waste in the garbage disposal of multifunctional high-rise buildings. Stage I
SO 153-34.10.105: Standard Sets of Equipment, Accessories, Tools, and Aids for Renovation of Smokestacks and Cooling Towers and Corrosion Protection of Equipment at Electric Power Generating Stations Administered by Minenergo USSR
|
Customers Who Viewed This Item Also Viewed:
 |
Petroleum products. Method for measurement of viscosity by automatic capillar viscosimeter
Language: English |
Greases. Method for determination of ultimate strength and thermostrengthening
Language: English |
Pipe fittings. Ball valves made of brass. General specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
