GOST R 51753-2001
ГОСТ Р 51753-2001
|
|
High pressure cylinders for the compressed natural gas as a fuel for automotive vehicles. General specifications
Баллоны высокого давления для сжатого природного газа, используемого в качестве моторного топлива на автомобильных транспортных средствах. Общие технические условия
Status: Not effective - Canceled. Registration information 563-st dated 06/20/2017 (official website of Rosstandart); IUS 11-2017
This standard applies to cylinders with a capacity of 20 to 500 liters, designed for a working pressure of not more than 40.0 MPa, installed on motor vehicles and intended for transportation, storage and use of compressed natural gas as a motor fuel according to GOST 27577. The standard applies to cylinders: seamless steel; consisting of a metal liner and a shell made of composite material on the cylindrical surface of the liner; consisting of a metal liner and a shell made of composite material on the entire surface of the liner; consisting of non-metallic liner, shells made of composite material on the entire surface of the liner and metal embedded elements. The standard does not apply to cylinders: all-metal welded; all-metal from aluminum alloys; all-metal from corrosion steels; with corrosion resistant steel liner
Настоящий стандарт распространяется на баллоны вместимостью от 20 до 500 л, рассчитанные на рабочее давление не более 40,0 МПа, устанавливаемые на автомобильные транспортные средства и предназначенные для транспортирования, хранения и использования в качестве моторного топлива сжатого природного газа по ГОСТ 27577. Стандарт распространяется на баллоны: стальные бесшовные; состоящие из металлического лейнера и оболочки из композиционного материала на цилиндрической поверхности лейнера; состоящие из металлического лейнера и оболочки из композиционного материала на всей поверхности лейнера; состоящие из неметаллического лейнера, оболочки из композиционного материала на всей поверхности лейнера и металлических закладных элементов. Стандарт не распространяется на баллоны: цельнометаллические сварные; цельнометаллические из алюминиевых сплавов; цельнометаллические из коррозионных сталей; с лейнером из коррозионностойких сталей
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstandart of Russia,
5/29/2001
SKU: RUSS71004
The Product is Contained in the Following Classifiers:
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Metal structures »
Welding regulations »
Welding materials »
Welding regulations »
welding equipment »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Welding work »
Surfacing »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Main materials »
Non-ferrous metals »
Welding regulations »
Welding materials »
Gases »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
018/2011 TR CU. On safety of wheeled vehicles »
Regulations and standards (to 018/2011 TR CU) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
032/2013 TR CU. On safety of overpressure equipment »
Regulations and standards (to 032/2013 TR CU) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.14 Testing and monitoring of vehicles and equipment »
4.14.1 Motor vehicles and equipment »
ISO classifier »
43 ROAD TRANSPORT TECHNOLOGY »
43.020 Road vehicles in general »
National standards »
43 ROAD TRANSPORT TECHNOLOGY »
43.020 Road vehicles in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
V Metals and metal products »
V6 Pipes metal and pipe products »
V66 Steel Cylinders »
National Standards for KGS (State Standards Classification) ��
Latest edition »
D Vehicles and packaging »
D2 Cars, tractors and tow trucks »
D24 automotive engines and parts for them »
National Standards for OKSTU »
PRODUCTS OF THE AUTOMOTIVE INDUSTRY »
Unified units and parts used in the automotive industry »
The Document References:
GOST 10006-80: Metal pipes
GOST 11262-80: Plastics. Tensile strength test method.
GOST 12247-80: Large seamless steel gas cylinders for operating pressure of 31,4 and 39,2 MPa (320 and 400 kgf/cm sq.). Specifications
GOST 14249-89: Vessels and apparatus. Norms and methods of strength calculation
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 17410-78: Non-destructive testing of seamless cylindrical metal pipes and tubes. Methods of ultrasonic imperfection detection.
GOST 21553-76: Plastics. Methods for determination of melting temperature
GOST 24297-87: Input inspection of products. General provisions.
GOST 24705-2004: Вasic norms of interchangeability. Metric screw thread. Basic dimensions
GOST 24705-81: Basic norms of interchangeability. Metric screw thread. Basic dimensions
GOST 27577-2000: Compressed natural fuel gas for internal-combustion engines. Specifications
GOST 27577-87: Compressed natural fuel gas for gas-driven vehicles
GOST 30432-96: Metal tubes. Selection of samples, tube stocks and specimens for mechanic and technological tests
GOST 4784-97: Aluminium and wrought aluminium alloys. Grades
GOST 6611.2-73: Textile threads. Methods for determination of breaking load and elongation at rupture
GOST 6943.10-79: Glass textile products. Method for determination of breaking load and elogation at rupture
GOST 6996-66: Welded joints. Methods of mechanical properties determination
GOST 9.019-74: Unified system of corrosion and ageing protection. Aluminium and magnesium alloys. Accelerated test methods for corrosion crocking
GOST 9.021-74: Unified system of corrosion and ageing protection. Aluminium and aluminium alloys. Accelerated test methods for intercrystalline corrosion
GOST 9012-59: Metals. Method of Brinell hardness measurement
GOST 9150-2002: Basic norms of interchangeability. Metric screw threads. Profile
GOST 9150-81: Basic norms of interchangeability. Metric screw thread. Profile
GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature
GOST 9731-79: Large capacity seamless steel gas-cylinders for operation pressure 4.5 MPa (250 kgf / cm2)
GOST 9909-81: Basic norms of interchangeability. Taper screw thread of valves and gas cylinder
GOST R 15.201-2000: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture
GOST R 50599-93: Welded steel vessels and apparatus under high pressure. Non-destructive control while the manufacturing and operating
PB 03-164-97: Standards for Fabrication of Steam and Hot-Water Boilers, Pressure Vessels, and Steam and Hot Water Piping by Welding
PB 10-115-96: Regulations of design and safe operation of pressure vessels
The Document is Referenced By:
Decision 219: The list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis to ensure compliance with the requirements of the technical regulations of the Customs Union "On the safety of wheeled vehicles". (TR CU 018/2011), and a list of international and regional (interstate) standards, and in their absence - national (state) standards containing the rules and methods of research (tests) and measurements, including sampling rules necessary for the application and implementation of the requirements of technical regulations of the Customs Union "On the safety of wheeled vehicles" (TR CU 018/2011) (TR CU 018/2011) and conformity assessment of objects of technical regulation
Decision 88: About the Program for the development (amendment, revision) of interstate standards, the application of which on a voluntary basis ensures compliance with the technical regulations of the Customs Union
GOST R 54114-2010: Transportable gas storage devices and systems for storing hydrogen based on metal hydrides
GOST R 55559-2013: Composite cylinders for liquefied petroleum gases at pressure up to 2,0 MPa. General technical requirements. Test methods
GOST R ISO 11439-2010: Gas cylinders. High pressure cylinders for the on-board storage of natural gas as a fuel. Specifications
POT R M-027-2003: Intersectoral rules on labor protection in road transport
RD 03112194-1095-03: Guidelines for the organization of operation of gas-cylinder vehicles operating on compressed natural gas
RD 03112194-1099-03: Guidance on organizing and rendering of services and jobs on conversion of vehicles to exploitation of compressed natural gas
|
Customers Who Viewed This Item Also Viewed:
 |
Building materials. Methods for combustibility test
Language: English |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Building materials spread flame test method
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
