GOST 2208-2007
ГОСТ 2208-2007
|
|
Brass foil, ribbons, strips, sheets and plates. Specifications
Фольга, ленты, полосы, листы и плиты латунные. Технические условия
Status: Effective - Supersedes. IUS 12-2007
The standard applies to brass cold-rolled foil, ribbons, cold-rolled and hot-rolled plates for general use. The standard does not apply to brass tapes intended for radiators.
Стандарт распространяется на латунные холоднокатаные фольгу, ленты, холоднокатаные и горячекатаные плиты общего назначения. Стандарт не распространяется на латунные ленты, предназначенные для радиаторов.
Choose Language:
Format: Electronic (pdf/doc)
Page Count: 40
Approved: Federal Agency for Technical Regulation and Metrology,
9/12/2007
SKU: RUSS71221
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
77 Metallurgy »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.12 Testing and control of products of metallurgical industry »
4.12.5 Non-ferrous metal products »
ISO classifier »
77 METALLURGY »
77.150 Non-ferrous metal products »
77.150.30 Copper products »
National standards »
77 METALLURGY »
77.150 Non-ferrous metal products »
77.150.30 Copper products »
National Standards for KGS (State Standards Classification) »
Latest edition »
V Metals and metal products »
V5 Non-ferrous metals and their alloys. Rolled non-ferrous metals »
V54 Tapes »
As a Replacement Of:
GOST 2208-91: Brass strips for general use. Specifications
GOST 931-90: Brass sheets and strips. Specifications
The Document References:
GOST 1.0-92: State System for Standardization of Russian Federation. Basic principles
GOST 1.2-97: Interstate system for standardization. Interstate standards, rules and recommendations on interstate standardization. Procedure for development, taking over application, renovation and cancellation
GOST 10198-91: Wooden boxes for weights of mass over 200 up to 20000 kg. General specifications
GOST 10510-80: Metals. Erikson test method for sheets and strips extrusion
GOST 11701-84: Metals. Methods of tensile testing of thin sheets and strips
GOST 14019-2003: Metallic materials. Bend test method
GOST 14192-96: Cargo marking
GOST 1497-84: Metals. Methods of tension test
GOST 15102-75: Universal metallic closed container of nominal gross mass 5,0 tn. Specifications
GOST 15527-2004: Pressure treated copper zinc alloys (brasses). Grades
GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage
GOST 1652.10-77: Copper-zinc alloys. Methods for the determination of aluminium
GOST 1652.11-77: Copper-zinc alloys. Methods for the determination of nickel
GOST 1652.12-77: Copper-zinc alloys. Methods for the determination of silicon
GOST 1652.13-77: Copper-zinc alloys. Methods for the determination of phosphorus
GOST 1652.1-77: Copper-zinc alloys. Methods for the determination of copper
GOST 1652.2-77: Copper-zinc alloys. Methods for the determination of lead
GOST 1652.3-77: Copper-zinc alloys. Methods for the determination of iron
GOST 1652.4-77: Copper-zinc alloys. Methods for the determination of manganese
GOST 1652.5-77: Copper-zinc alloys. Methods for the determination of tin
GOST 1652.6-77: Copper-zinc alloys. Methods for the determination of antimony
GOST 1652.7-77: Copper-zinc alloys. Methods for the determination of bismuth
GOST 1652.8-77: Copper-zinc alloys. Methods for the determination of arsenic
GOST 1652.9-77: Copper-zinc alloys. Methods for the determination of sulphur
GOST 166-89: Vernier callipers. Specifications
GOST 18242-72: Statistical acceptance inspection by alternative feature inspection plans
GOST 18321-73: Statistical quality control. Item random sampling methods
GOST 18477-79: Universal containers
GOST 20435-75: Universal metallic closed container of nominal gross mass 3,0 tn. Specifications
GOST 21073.1-75: Non-ferrous metals. Determination of grain size by comparison with microstructure scale
GOST 21140-88: Containers
GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements
GOST 2208-91: Brass strips for general use. Specifications
GOST 22225-76: Containers multipurpose gross weight 0,625 and 1,25 t. Specifications
GOST 24047-80: Half-finished products out of non-ferrous metals and their alloys. Sampling for tensile test
GOST 24231-80: Non-ferrous metals and alloys. General requirements for sampling and sample preparation for chemical analysis
GOST 25086-87: Nonferrous metals and their alloys. General requirements for methods of analysis
GOST 26653-90: Preparation of general cargoes for transportation. General requirements
GOST 26663-85: Transport packets. Formation by packaging means. General technical requirements
GOST 26877-2008: Metal products. Methods of measuring form variations
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 2999-75: Metals and alloys. Vickers hardness teat by diamond pyramid
GOST 3282-74: General-purpose low-carbon steel wire. Specifications
GOST 3560-73: Sealing tepe
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 4381-87: Lever-type micrometers. General specifications
GOST 6507-90: Micrometers. Specifications
GOST 7376-89: Corrugated paperboard
GOST 7502-98: Measuring metal tapes. Specifications
GOST 7933-89: Cardboard for the retail containers
GOST 8273-75: Packing paper
GOST 9012-59: Metals. Method of Brinell hardness measurement
GOST 9078-84: Flat pallets
GOST 931-90: Brass sheets and strips. Specifications
GOST 9557-87: Flat wooden pallets with dimensions 800ґ1200 mm
GOST 9696-82: Multi-revolution dial indicators graduated in 0,001 and 0,002 mm. Types. Basic parameters. Specifications
GOST 9716.1-79: Copper-zinc alloys. Method of spectral analysis of metal standard specimens with photographic registration of spectrum
GOST 9716.2-79: Copper-zinc alloys. Method spectral analysis of metal standard specimens with photoelectric registration of spectrum
GOST 9716.3-79: Copper-zinc alloys. Method of spectral analysis of oxide specimens with photographic registration of spectrum
GOST R 52901-2007: Corrugated board for products packaging. General specifications
GOST R ISO 2859-1-2007: Statistical methods. Sampling procedures for inspection by attributes. Part 1. Sampling schemes indexed by acceptance quality limit for lot-by-lot inspection
ST SEV 543-77: Numbers. Requirements for Notation and Rounding Off
The Document is Referenced By:
GOST 11679.2-2019: Rubber-metal instrument dampers. Fittings. Technical specifications
GOST 18707-81: Jumpers for protection of rocketry and space-rocketry items from static electricity
GOST 19681-2016: Sanitary and technical water fittings. General specifications
GOST 20707-2015: Copper and brass ribbons for radiators. Specifications
GOST 28759.7-90: Asbestos-metal gaskets
GOST 33260-2015: Pipeline valves. Мetals used in pipeline valves production. Basic requirements for choice of materials
GOST 33553-2015: Automobile transport facilities. Tips of low voltage wires. Requirements and test methods
GOST 33667-2015: Automobile transport facilities. The tips of the wires to the terminals of the batteries and starters. Requirements and test methods
GOST 34233.4-2017: Vessels and apparatus. Norms and methods of strength calculation. Calculation of the strength and tightness of flange connections
GOST 34347-2017: Steel welded vessels and apparatus. General technical conditions
GOST R 52630-2012: Steel welded vessels and apparatus. General specifications.
GOST R 52857.4-2007: Vessels and apparatus. Norms and methods of strength calculation. Stength and leak-tightness calculation of flange joints
GOST R 53617-2009: Carbon brushes for electrical machines. Construction. Types and dimensions
GOST R 55509-2013: Pipeline valves. Metals used in pipeline valves production. Basic requirements for choice of materials
GOST R 55873-2013: Activated carbon. Standard Test Method for Hardness
GOST R 56727-2015: Self-stressing cements. Specifications
OST 26.260.463-99: Asbestos-metal packing for fitting flanges. Design, dimensions and general specifications. .
PKO-2010.6: Reference materials for the design work of the electrical part of the project
RD 26-15-88: Vessels and apparatus. Norms and methods of strength and tightness calculation for flanged joints.
RK 34-38-025-87: Guide to Overhaul of Indicating Pressure Gauges for Precise Measurements Type MTI
RMD 23-16-2012 Sankt-Peterburg: Recommendations for energy efficiency in residential and public buildings
ST TsKBA 005.1-2003: Pipe fittings. Metals used in the valve industry. Part 1. Basic requirements for the choice of materials
ST TsKBA 070-2009: Pipe fittings. Symbol of materials in the design documentation
TU 3612-023-00220302-01: Shell-and-tube heat exchangers with a floating head, shell-and-tube with U-tubes and tube bundles for them
TU 3612-024-00220302-02: Shell and tube heat exchangers with fixed tube sheets and shell and tube with temperature compensator on the shell
Customers Who Viewed This Item Also Viewed:
 |
Special railway rolling stok. Dynamic and strength testing procedures
Language: English |
Blanks for marine shafts and rudder stocks. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.