GOST R 1.5-2004

ГОСТ Р 1.5-2004

Standardization in the Russian Federation. National standards of the Russian Federation. Rules of structure, drafting, presentation and indication

Стандартизация в Российской Федерации. Стандарты национальные Российской Федерации. Правила построения, изложения, оформления и обозначения

Status: Not effective - Superseded. IUS 9-2013

This standard establishes the rules for the construction, presentation, designation and designation of national standards of the Russian Federation, the general requirements for their content, as well as the rules for design and presentation of changes to the national standards of the Russian Federation. This standard does not apply to the existing national standards of the Russian Federation, which were approved (adopted) prior to its implementation. Their alignment with the requirements of this standard is carried out at the next revision of these standards, and in justified cases, when developing the next changes to them. When using this standard in relation to defense products (works, services) supplied for federal state needs for state defense orders, products (works, services) used to protect information constituting state secrets, or classified as protected by law Federation of information of limited access, products (works, services), information about which is a state secret, also take into account the additional requirements data in special standards establishing the rules for the development of these documents. Certain rules and requirements of this standard can be applied to the standards of organizations.

Настоящий стандарт устанавливает правила построения, изложения, оформления и обозначения национальных стандартов Российской Федерации, общие требования к их содержанию, а также правила оформления и изложения изменений к национальным стандартам Российской Федерации. Настоящий стандарт не распространяется на действующие национальные стандарты Российской Федерации, которые были утверждены (приняты) до введения его в действие. Их приведение в соответствие с требованиями настоящего стандарта осуществляют при очередном пересмотре указанных стандартов, а в обоснованных случаях - при разработке очередных изменений к ним. При использовании настоящего стандарта применительно к оборонной продукции (работам, услугам), поставляемой для федеральных государственных нужд по государственному оборонному заказу, продукции (работам, услугам), используемой в целях защиты сведений, составляющих государственную тайну, или относимой к охраняемой в соответствии с законодательством Российской Федерации информации ограниченного доступа, продукции (работам, услугам), сведения о которой составляют государственную тайну, учитывают также дополнительные требования, изложенные в специальных стандартах, устанавливающих правила разработки указанных документов. Отдельные правила и требования настоящего стандарта могут быть применены в отношении стандартов организаций

Choose Language: 
Format: Electronic (pdf/doc)
Page Count: 35

Approved: Federal Agency for Technical Regulation and Metrology, 12/30/2004

SKU: RUSS71257

Price: $441.75




The Product is Contained in the Following Classifiers:

Construction (Max) » Standards » Other state standards used in construction » 01 General. Terminology. Standardization. Documentation »

PromExpert » SECTION I. TECHNICAL REGULATION » II Standardization » 1 Basic provisions of standardization system »

ISO classifier » 01 GENERAL PROVISIONS. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION » 01.120 Standardization. General rules »

National standards » 01 GENERAL PROVISIONS. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION » 01.120 Standardization. General rules »

National Standards for KGS (State Standards Classification) » Latest edition » T General technical and organizational and methodological standards » T5 Documentation System » T50 State system of standardization and normative and technical documentation »


The Document is Replaced With:

GOST R 1.5-2012: Standardization in Russian Federation. National Standards. Rules of structure, drafting, presentation and indication

As a Replacement Of:

GOST R 1.5-2002: State system for standardization of Russian Federation. Standards. General requirements for structure, drafting, presentation, content and indication

The Document References:

Federal Law 184-FZ: About technical regulation

GOST 1.1-2002: Interstate system for standardization. Terms and definitions

GOST 1.5-2001: Interstate system for standardization. Interstate standards, rules and recommendations on interstate standardization. General requirements for structure, drafting, presentation, content and indication

GOST 27484-87: Fire hazard testing. Test methods. Needle-flame test

GOST 28108-89: Caps for light sources. Types, main and coupling dimensions, gauges

GOST 28312-89: Radioelectronic equipment, professional. Conventional graphic designations

GOST 30687-2000: Earth-moving machinery. Engine test code. Net power

GOST 7.4-95: System of standards on information, librarianship and publishing. Publications. Imprint

GOST ISO 8601-2001: System of standards on information, librarianship and publishing. Representation of dates and times. General requirements

GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions

GOST R 1.12-2004: Standardization in the Russian Federation. Terms and definitions

GOST R 1.12-99: State system for standardization of Russian Federation. Standardization and related activities. Terms and definitions

GOST R 1.2-2004: Standardization in the Russian Federation. National standards of the Russian Federation. Rules for development, taking over, reform and cancellation

GOST R 1.5-2002: State system for standardization of Russian Federation. Standards. General requirements for structure, drafting, presentation, content and indication

GOST R 1.5-92: State system for standardization of the Russian Federation. General requirements for lay-out, formulation, presentation and contents of standards

GOST R 22.10.01-2001: Safety in emergencies. Evaluation of damage. Terms and definitions

GOST R 50233.1-92: Niobium pentoxide. Coulonometry method for determination of sulphur content

GOST R 50233.2-92: Niobium pentoxide. Ionometry method for determination of fluor content

GOST R 50233.3-92: Niobium pentoxide. Luminescent method for determination of phosphorus content

GOST R 50628-2000: Electromagnetic compatibility of technical equipment. Immunity of personal computers to electromagnetic disturbances. Requirements and test methods

GOST R 50779.11-2000: Statistical methods. Statistical quality control. Terms and definitions

GOST R 50779.42-99: Statistical methods. Shewhart control charts

GOST R 51657.0-2000: Water flow measurement in hydromelioration and water economics systems. Basic principles

GOST R 51657.1-2000: Water flow measurement in hydromelioration and water economic systems. Terms and definitions

GOST R 51657.2-2000: Water flow measurement in hydromelioration and water economics systems. Methods of water flow measurement. Classification

GOST R 51657.3-2000: Water flow measurement in hydromelioration and water economics system. Flow gauging structures. Classification

GOST R 51885-2002: Public information symbols

GOST R 8.563-96: State system for ensuring the uniformity of measurements. Procedures of measurements

GOST R IEC 60598-1-2003: Luminaires. Part 1. General requirements and test methods

GOST R IEC 60851-5-2002: Winding wires. Test methods. Part 5. Electrical properties

GOST R ISO 13408-1-2000: Aseptic processing of health care products. Part 1: General requirements

OK 001-2000: All-Russian classification for standards

OK 002-93: All-Russian classification of services provided to people

OK 004-93: All-Russian classification of economic activities and products

The Document is Referenced By:

GOST 12.1.016-79: Work area air

GOST 31440.2-2011: Reciprocating internal combustion engines. Safety requirements for design and construction of engines for use in potentially explosive atmospheres. Part 2. Group I engines for use in underground workings susceptible to fired amp and/or combustible dust

GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions

GOST R 1.10-2004: Standardization in the Russian Federation. Rules for standardization and recommendations for standardization. Order of elaboration, confirmation, amendment, revision and abrogation

GOST R 1.15-2009: Standardization in the Russian Federation. Company standards department. Rules of organization and function

GOST R 1.2-2004: Standardization in the Russian Federation. National standards of the Russian Federation. Rules for development, taking over, reform and cancellation

GOST R 1.4-2004: Standardization in Russian Federation. Standards of organizations. General

GOST R 1.5-2012: Standardization in Russian Federation. National Standards. Rules of structure, drafting, presentation and indication

GOST R 1.6-2005: Standardization in the Russian Federation. Draft standards. Organization of realization of expertise

GOST R 1.7-2008: Standardization in the Russian Federation. National standards of the Russian Federation. Rules of presentation and indication by development on the basis of application of international standards

GOST R 1.8-2004: Standardization in the Russian Federation. Interstate standards. Rules of developing, application, renovation and cease application in the Russian Federation

GOST R 12.4.230.1-2007: Occupational safety standards system. Personal eyes protection means. General technical requirements

GOST R 12.4.230.2-2007: Occupational safety standards system. Personal eye protection. Optical and non-optical parameters test methods

GOST R 12.4.234-2007: Occupational safety standards system. Protective clothing for thermal hazards of an electric arc. General technical requirement and test methods

GOST R 12.4.235-2007: Occupational safety standards system. Respiratory protective devices. List of equivalent terms

GOST R 12.4.237-2007: Occupational safety standards system. Protective clothing. Methods of testing the material on impact of splashes of molten metal

GOST R 12.4.238-2007: Occupational safety standards system. Personal eye and face protection equipment during welding and related processes. General specifications

GOST R 12.4.245-2007: Occupational safety standards system. Bump caps. General technical requirements. Test methods

GOST R 12.4.254-2010: Occupational safety standards system. Personal eye-protection. Filters and eye-protection against laser radiation. General technical requirements and test methods

GOST R 12.4.255-2011: Occupation safety standards system. Personal hearing protective equipment. General technical requirements. Mechanical test methods

GOST R 12.4.256-2011: Occupational safety standards system. Protective clothing against toxic chemicals in the form of gas and vapours. Technical requirements and test methods

GOST R 12.4.257-2011: Occupational safety standards system. Protective clothing against liquid chemicals. Performance requirements for chemical protective clothing offering limited protective performance against liquid chemicals (Types 6 and PB [6])

GOST R 12.4.258-2011: Occupational safety standards system. Protective clothing against liquid chemicals. Performance requirements for liquid tight or spray-tight clothing (Types 3 and 4). Technical requirements

GOST R 12.4.259-2011: Occupational safety standards system. Ventilated and non-ventilated «gas-tight» (Type 1) and «non-gas-tight» (Type 2) chemical protective suits. Technical requirements

GOST R 12.4.260-2011: Occupational safety standards system. Special clothing for protection from mechanical action. Method for determination of resistance to puncture

GOST R 12.4.261-2011: Occupational safety standards system. Special clothing for protection from toxic chemicals. Determination of resistance to penetration by sprayed liquid chemicals, emulsions and dispersions

GOST R 12.4.262-2011: Occupational safety standards system. Protective clothing against toxic chemicals. Method for determination of resistance to permeation by liquids and gases

GOST R 14.01-2005: Ecological management. General rules and objectives of regulation

GOST R 41.43-2005: Uniform provisions concerning the safety glazing materials and their installation on vehicles

GOST R 41.55-2005: Uniform provisions concerning mechanical coupling components of combinations of vehicles

GOST R 41.95-2005: Uniform provisions concerning the protection of the occupants of vehicles in the event of a lateral collision

GOST R 50030.2-2010: Low-voltage switchgear and control gear. Part 2. Circuit-breakers

GOST R 50030.5.4-2011: Low-voltage switchgear and control gear. Part 5-4. Control circuit devices and switching elements. Method of assessing the performance of low-energy contacts. Special tests

GOST R 50030.5.5-2011: Low-voltage switchgear and control gear. Part 5-5. Control circuit devices and switching elements. Electrical emergency stop devices with mechanical latching function

GOST R 50030.5.8-2013: Low-voltage switchgear and control gear. Part 5-8. Control circuit devices and switching elements. Three-position enabling switches

GOST R 50345-2010: Electrical accessories. Circuit-breakers for overcurrent protection for household and similar installations. Part 2. Circuit-breakers for a.c. operation

GOST R 50397-2011: Electromagnetic compatibility of technical equipment. Тerms and definitions

GOST R 50571.1-2009: Low-voltage electrical installations. Part 1. Fundamental principles, assessment of general characteristics and definitions

GOST R 50571-4-44-2011: Low-voltage electrical installations. Part 4-44. Safety requirements. Protection against voltage disturbances and electromagnetic disturbances

GOST R 50696-2006: Domestic cooking appliances burning gas. General technical requirements and test methods

GOST R 50779.24-2005: Interpretation of statistical data. Estimation of a median

GOST R 50779.25-2005: Statistical methods. Statistical interpretation of data. Power of tests relating to means and variances

GOST R 50779.26-2007: Statistical methods. Point estimates, confidence intervals, prediction intervals and tolerance intervals for exponential distribution

GOST R 50779.27-2007: Statistical methods. Goodness-of-fit tests and confidence intervals for Weibull distributed data

GOST R 50779.28-2007: Statistical methods. Power law model. Goodness of-fit tests and estimation methods

GOST R 50827.1-2009: Boxes and enclosures for electrical accessories for household and similar fixed electrical installations. Part 1. General requirements

GOST R 50827.2-2009: Boxes and enclosures for electrical accessories for household and similar fixed electrical installations. Part 21. Particular requirements for boxes and enclosures with provision for suspension means

GOST R 50827.4-2009: Boxes and enclosures for electrical accessories for household and similar fixed electrical installations. Part 23. Particular requirements for floor boxes and enclosures

GOST R 50827.5-2009: Boxes and enclosures for electrical accessories for household and similar fixed electrical installations. Part 24. Particular requirements for boxes and enclosures for housing protective devices and similar power consuming devices

GOST R 50838-2009: Polyethylene pipes for the supply of gaseous fuel. Specifications

GOST R 51317.1.2-2007: Electromagnetic compatibility of technical еquipment. Methodology for the achievement of the functional safety of technical equipment with regard to electromagnetic disturbance

GOST R 51317.1.5-2009: Electromagnetic compatibility of technical equipment. High power electromagnetic influences on civil systems. Basic provisions

GOST R 51317.3.2-2006: Electromagnetic compatibility of technical equipment. Harmonic current emissions (equipment input current <=16 A per phase). Limits and test methods.

GOST R 51317.4.11-2007: Electromagnetic compatibility of technical equipment. Voltage dips, short interruptions and voltage variations immunity. Requirements and test methods

GOST R 51317.4.2-2010: Electromagnetic compatibility of technical equipment. Electrostatic discharge immunity. Requirements and test methods.

GOST R 51317.4.30-2008: Electric energy. Electromagnetic compatibility of technical equipment. Power quality measurement methods

GOST R 51317.4.3-2006: Electromagnetic compatibility of technical equipment. Radio-frequency electromagnetic field immunity. Requirements and test methods.

GOST R 51317.4.34-2007: Electromagnetic compatibility of technical equipment. Voltage dips, short interruptions and voltage variations immunity for equipment with input current more than 16 A per phase. Requirements and test methods

GOST R 51317.4.4-2007: Electromagnetic compatibility of technical equipment. Immunity to nanosecond impulsive disturbance. Requirements and test methods

GOST R 51317.4.7-2008: Electromagnetic compatibility of technical equipment. General guide on harmonics and interharmonics measuring instruments and measurement, for power supply systems and equipment connected thereto

GOST R 51317.6.1-2006: Electromagnetic compatibility of technical equipment. Immunity of technical equipment intended for use in residential, commercial and light-industrial environments. Requiremеnts and test methods

GOST R 51317.6.2-2007: Electromagnetic compatibility of technical equipment. Immunity of technical equipment intended for use in industrial environments. Requirements and test methods

GOST R 51317.6.3-2009: Electromagnetic compatibility of technical equipment. Electromagnetic disturbance from technical equipment intended for use in residential, commercial and light-industry environments Limits and test methods

GOST R 51317.6.4-2009: Electromagnetic compatibility of technical equipment. Electromagnetic disturbance from technical equipment intended for use in industry environments. Limits and test methods

GOST R 51317.6.5-2006: Electromagnetic compatibility of technical equipment. Immunity of technical equipment intended for use in power stations and substations. Requirements and test methods

GOST R 51318.11-2006: Electromagnetic compatibility of technical equipment. Industrial, scientific, medical and domestic (ISMD) high-frequency equipment. Radio disturbance. Limits and methods of measurement

GOST R 51318.13-2006: Electromagnetic compatibility of technical equipment. Sound and television broadcast receivers and associated equipment. Radio disturbance. Limits and methods of measurement

GOST R 51318.16.1.1-2007: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 1-1. Radio disturbance and immunity measuring apparatus. Measuring apparatus

GOST R 51318.16.1.2-2007: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 1-2. Radio disturbance and immunity measuring apparatus and methods. Conducted radio disturbance measuring and immunity test apparatus

GOST R 51318.16.1.3-2007: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 1-3. Radio disturbance and immunity measuring apparatus. Disturbance power measuring apparatus

GOST R 51318.16.1.4-2008: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 1-4. Radio disturbance and immunity measuring apparatus. Radiated radio disturbance measuring and immunity test apparatus

GOST R 51318.16.2.1-2008: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-1. Methods of measurement of radio disturbances and immunity. Conducted radio disturbance measurements

GOST R 51318.16.2.3-2009: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-3. Methods of measurement of radio disturbances and immunity. Radiated radio disturbance measurements

GOST R 51318.16.2.4-2010: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-4. Methods of measurement of disturbances and immunity. Immunity parameters measurement

GOST R 51318.16.2.5-2011: Electromagnetic compatibility of technical equipment. Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-5. In situ measurements of radio disturbance produced by physically large equipment

GOST R 51318.22-2006: Electromagnetic compatibility of technical equipment. Information technology equipment. Man-made radio disturbance. Limits and methods of measurement

GOST R 51321.3-2009: Low-voltage switchgear and control gear assemblies. Part 3. Particular requirements for low-voltage switchgear and control gear assemblies intended to be installed in places where unskilled persons have access for their use and test methods

GOST R 51324.1-2005: Switches for household and similar fixed electrical installations. General requirements and tests methods

GOST R 51327.1-2010: Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs). Part 1. General rules and test methods

GOST R 51382-2011: Heating boilers. Part 4. Heating boilers with forced draught burners. Special requirements for boilers with forced draught oil burners with output up to 70 kW and maximum operating pressure of 0,3 MPa. Terminology, special requirements, test methods and marking

GOST R 51387-99: Energy conservation. Norm-method securing. Basic concept

GOST R 51522.1-2011: Electromagnetic compatibility of technical equipment. Electrical equipment for measurement, control and laboratory use. Part 1. General requirements and test methods

GOST R 51522.2.1-2011: Electromagnetic compatibility of technical equipment. Electrical equipment for measurement, control and laboratory use. Part 2-1. Particular requirements for sensitive test and measurement equipment for EMC unprotected applications. Test configurations, operational conditions and performance criteria

GOST R 51522.2.2-2011: Electromagnetic compatibility of technical equipment. Electrical equipment for measurement, control and laboratory use. Part 2-2. Particular requirements for portable test, measuring and monitoring equipment used in low-voltage distribution systems. Test configurations, operational conditions and performance criteria

GOST R 51522.2.4-2011: Electromagnetic compatibility of technical equipment. Electrical equipment for measurement, control and laboratory use. Part 2-4. Particular requirements for insulation monitoring devices and insulation fault location equipment. Test configurations, operational conditions and performance criteria

GOST R 51526-2012: Electromagnetic compatibility of technical equipment. Arc welding equipment. Part 10. Requirements and test methods

GOST R 51631-2008: Passenger lifts. Technical requirements of accessibility for persons including persons with disability

GOST R 51725.16-2012: Catalogization of products for federal state needs. The order of formation, management and application of the Unified codifier and the list of the approved names of items of supply

GOST R 51876-2008: Series 1 freight containers. Technical requirements and test methods. Part 1. General-purpose containers

GOST R 51891-2008: Series 1 freight containers. Fittings. Specifications

GOST R 51897-2011: Risk management. Terms and definition

GOST R 51901.10-2009: Risk management. Fire risk management in enterprise

GOST R 51901.11-2005: Risk management. Hazard and operability studies. Application guide

GOST R 51901.12-2007: Risk management. Procedure for failure mode and effects analysis

GOST R 51901.14-2005: Risk management. Reliability block diagram method

GOST R 51901.14-2007: Risk management. Reliability block diagram and Boolean methods

GOST R 51901.15-2005: Risk management. Application of Markov techniques

GOST R 51901.16-2005: Risk management. Reliability growth. Statistical test and estimation methods

GOST R 51901.3-2007: Risk management. Guidelines for dependability management

GOST R 51901.4-2005: Risk management. Application guidelines for projects

GOST R 51901.6-2005: Risk management. Programme for reliability growth

GOST R 51908-2002: General requirements for machines, instruments and other industrial products as to storage and transporting conditions

GOST R 51942-2010: Gasolines. Determination of lead by method of atomic absorption spectrometry

GOST R 52065-2007: Caplights for use in mines susceptible to firedamp. Part 1. General requirements and testing methods in relation to the risk of explosion

GOST R 52069.0-2003: Safety of information. System of standards. Basic principles

GOST R 52069.0-2013: Safety of information. System of standards. Basic principles

GOST R 52161.2.10-2005: Safety of household and similar electrical appliances. Part 2.10. Particular requirements for floor treatment machines and wet scrubbing machines

GOST R 52161.2.11-2005: Safety of household and similar electrical appliances. Part 2.11. Particular requirements for tumble dryers

GOST R 52161.2.12-2005: Safety of household and similar electrical appliances. Part 2.12. Particular requirements for warming plates and similar appliances

GOST R 52161.2.17-2009: Safety of household and similar electrical appliances. Part 2.17. Particular requirements for blankets, pads, clothing and similar flexible heating appliances

GOST R 52161.2.21-2006: Safety of household and similar electrical appliances. Part 2.21. Particular requirements for storage water heaters

GOST R 52161.2.2-2005: Safety of household and similar electrical appliances. Part 2.2. Particular requirements for vacuum cleaners and water-suction cleaning appliances

GOST R 52161.2.23-2007: Safety of household and similar electrical appliances. Part 2.23. Particular requirements for skin or hair care devices

GOST R 52161.2.24-2007: Safety of household and similar electrical appliances. Part 2.24. Particular requirements for refrigerating appliances, ice-cream appliances and ice-makers

GOST R 52161.2.27-2008: Safety of household and similar electrical appliances. Part 2.27. Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation

GOST R 52161.2.29-2007: Safety of household and similar electrical appliances. Part 2.29. Particular requirements for battery chargers

GOST R 52161.2.31-2007: Safety of household and similar electrical appliances. Part 2.31. Particular requirements for range hoods

GOST R 52161.2.32-2008: Safety of household and similar electrical appliances. Part 2.32. Particular requirements for massage appliances

GOST R 52161.2.35-2008: Safety of household and similar electrical appliances. Part 2.35. Particular requirements for instantaneous water heaters

GOST R 52161.2.41-2008: Safety of household and similar electrical appliances. Part 2.41. Particular requirements for pumps

GOST R 52161.2.43-2008: Safety of household and similar electrical appliances. Part 2.43. Particular requirements for clothes dryers and towel rails

GOST R 52161.2.44-2008: Safety of household and similar electrical appliances. Part 2.44. Particular requirements for ironers

GOST R 52161.2.51-2008: Safety of household and similar electrical appliances. Part 2.51. Particular requirements for stationary circulation pumps for heating and service water installations

GOST R 52161.2.5-2005: Safety of household and similar electrical appliances. Part 2.5. Particular requirements for dishwashers

GOST R 52161.2.59-2008: Safety of household and similar electrical appliances. Part 2.59. Particular requirements for insect killers

GOST R 52161.2.60-2011: Safety of household and similar electrical appliances. Part 2.60. Particular requirements for whirlpool baths and whirlpool spas

GOST R 52161.2.6-2006: Safety of household and similar electrical appliances. Part 2.6. Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances

GOST R 52161.2.65-2008: Safety of household and similar electrical appliances. Part 2.65. Particular requirements for air-cleaning appliances

GOST R 52161.2.74-2008: Safety of household and similar electrical appliances. Part 2.74. Particular requirements for portable immersion heaters

GOST R 52161.2.9-2006: Safety of household and similar electrical appliances. Part 2.9. Particular requirements for grills, toasters and similar portable cooking appliances

GOST R 52161.2.96-2006: Safety of household and similar electrical appliances. Part 2.96. Particular requirements for flexible sheet heating elements for room heating

GOST R 52319-2005: Safety requirements for electrical equipment for measurement, control and laboratory use. Part 1. General requirements

GOST R 52332-2005: Aviation fuels. Determination of freezing point with automatic phase transition method

GOST R 52350.29.4-2011: Explosive atmospheres. Part 29-4. Gas detectors. General technical requirements and test methods of open path detectors for flammable gases

GOST R 52365-2005: Seals. Requirements for test methods of locking system reliability and resistance to unauthorized access

GOST R 52381-2005: Abrasive materials. Grain and grain size distribution of grinding powders. Test of grain size distribution

GOST R 52382-2005: Passenger lifts. Fire-fighters lifts

GOST R 52382-2010: Passenger lifts. Fire-fighters lifts

GOST R 52383-2005: Lifts. Fire safety

GOST R 52425-2005: Electricity metering equipment (a.c.). Particular requirements. Part 23. Static meters for reactive energy

GOST R 52434-2005: Active infra-red detectors. General technical requirements and test methods

GOST R 52459.10-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 10. Specific requirements for first and second generation cordless telephone equipment

GOST R 52459.1-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 1. General technical requirements and test methods

GOST R 52459.12-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 12. Specific requirements for very small aperture terminal, satellite earth stations operated in the frequency ranges between 4 GHz and 30 GHz in the fixed satellite

GOST R 52459.13-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 13. Specific requirements for private radio equipment operating at frequencies between 26965 kHz and 27860 kHz and ancillary equipment

GOST R 52459.14-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 14. Specific requirements for analogue and digital terrestrial TV broadcasting service transmitters

GOST R 52459.15-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 15. Specific requirement for commercially available amateur radio equipment

GOST R 52459.16-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 16. Specific requirements for analogue cellular radiocommunication equipment, mobile and portable

GOST R 52459.18-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 18. Specific requirement for terrestrial trunked radio (TETRA) equipment

GOST R 52459.19-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 19. Specific requirements for mobile receive only earth stations operating in the 1,5 GHz band providing data communications

GOST R 52459.20-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 20. Specific requirements for earth stations used in the mobile satellite services

GOST R 52459.2-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 2. Specific requirements for radio paging equipment

GOST R 52459.22-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 22. Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment

GOST R 52459.23-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 23. Specific requirements for IMT-2000 CDMA direct spread base station, repeater and ancillary equipment

GOST R 52459.24-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 24. Specific requirements for IMT-2000 CDMA direct spread mobile and portable radio and ancillary equipment

GOST R 52459.25-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 25. Specific requirements for CDMA 1x spread spectrum mobile stations and ancillary equipment

GOST R 52459.26-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 26. Specific requirements for CDMA 1x spread spectrum base stations, repeaters and ancillary equipment

GOST R 52459.27-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 27. Specific requirements for ultra-low power active medical implants and related peripheral devices

GOST R 52459.28-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 28. Specific requirements for wireless equipment of digital video links

GOST R 52459.31-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 31. Specific requirements for equipment in 9 kHz to 315 kHz band for ultra-low power active medical implants and related peripheral devices

GOST R 52459.3-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 3. Specific requirements for short-range devices operating at frequencies between 9 kHz and 40 GHz

GOST R 52459.32-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 32. Specific requirements for radar equipment for ground and wall probing

GOST R 52459.4-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 4. Specific requirements for radio equipment of fixed service stations and ancillary equipment

GOST R 52459.5-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 5. Specific requirements for private land mobile radio and ancillary equipment

GOST R 52459.6-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 6. Specific requirements for digital enhanced cordless telecommunications (DECT) equipment

GOST R 52459.7-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 7. Specific requirements for mobile and portable radio and ancillary equipment of digital cellular telecommunication systems (GSM and DCS)

GOST R 52459.8-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 8. Specific requirements for GSM base stations

GOST R 52459.9-2009: Electromagnetic compatibility of technical equipment. Radio communication equipment. Part 9. Specific requirements for wireless microphones, similar radio frequency audio link equipment, cordless audio and in-ear monitoring devices

GOST R 52485-2005: Paint materials. Determination of volatile organic compound (VOC) content. Difference method

GOST R 52486-2005: Paint materials. Determination of volatile organic compound (VOC) content. Gas-chromatographic method

GOST R 52487-2005: Paint materials. Determination of non-volatile-matter mass fraction

GOST R 52487-2010: Paint materials. Determination of non-volatile-matter mass fraction

GOST R 52489-2005: Paint materials. Colorimetry. Part 1. Principles

GOST R 52490-2005: Paint materials. Colorimetry. Part 3. Calculation of colour differences

GOST R 52501-2005: Water for analytical laboratory use. Specifications

GOST R 52527-2006: Gas turbine plants. Reliability, availability, maintainability and safety

GOST R 52543-2006: Hydraulic drives. Safety requirements

GOST R 52545.2-2012: Rolling bearings. Measuring methods for vibration. Part 2. Radial and angular ball bearings

GOST R 52588-2006: Abrasive tools. Safety requirements

GOST R 52600.0-2006: Protocols for patient's management. General

GOST R 52614.2-2006: Quality management systems. Guidelines for the application of GOST R ISO 9001-2001 in education

GOST R 52623.0-2006: Technologies of medical services. General

GOST R 52624-2006: Passenger lifts. Requirements for vandal resistance

GOST R 52625-2006: Lifts. Landing doors. Fire resistance test methods

GOST R 52626-2006: Lifts. Methodology of improvement assessment and of safety of existing lifts

GOST R 52627-2006: Bolts, screws and studs. Mechanical properties and test methods

GOST R 52628-2006: Nuts. Mechanical properties and test methods

GOST R 52643-2006: High-strength screws and nuts washers for metal structures. General specifications

GOST R 52644-2006: Hexagon bolts for high-strength structural bolting with large width across flats. Specifications.

GOST R 52645-2006: Hexagon nuts for high-strength structural bolting with large width across flats. Specifications.

GOST R 52646-2006: Washers for high-strength bolts metal structures. Specifications.

GOST R 52658-2006: Aviation turbine fuel. Method for determination of acid number

GOST R 52659-2006: Petroleum and petroleum products. Methods for manual sampling

GOST R 52660-2006: Automotive fuels. Method for determination of sulphur content by wavelength-dispersive X-ray fluorescence spectrometry

GOST R 52661-2006: Pulp, paper and board. Method for determination of total chlorine and organically bound chlorine content

GOST R 52662-2006: Paint materials. Colorimetry. Part 2. Colour measurement

GOST R 52666-2006: Lubricating oils. Determination of barium, calcium, magnesium and zinc concentrations by atomic absorption spectrometry method

GOST R 52696-2006: Shipbuilding. Inland navigation ships. Raft-type life-saving apparatus

GOST R 52706-2007: Tungsten filament lamps for domestic and similar general lighting purposes. Performance requirements

GOST R 52709-2007: Diesel fuels. Determination of cetane number

GOST R 52712-2007: Safety requirements for incandescent lamps. Part 1. Tungsten filament lamps for domestic and similar general lighting purposes

GOST R 52714-2007: Motor gasolines. Determination of individual and group hydrocarbon composition by method of capillary gas chromatography

GOST R 52715-2007: Vacuum equipment. Pipeline fittings. Mounting dimensions

GOST R 52740-2007: Paint materials. Method for determination of film strength while bending around cylindrical mandrel

GOST R 52743-2007: Pumps and pump units for pumping of liquids. General safety requirements

GOST R 52753-2007: Paint materials. Method for determination of fineness of grind

GOST R 52762-2007: Mechanical environment stability test methods for machines, instruments and other industrial products. Test methods for bumps to enclosure of products

GOST R 52764-2007: Metallic materials. Method of bend test for sheets and strips 3 mm thick and less

GOST R 52776-2007: Rotating electrical machines. Rating and performance

GOST R 52779-2007: Polyethylene fittings for gas pipelines. General specifications

GOST R 52780-2007: Hardmetal burrs. Specifications

GOST R 52782-2007: Gas turbines. Test methods. Acceptance tests

GOST R 52785-2007: Screwdrivers for fitting and assembling for recessed screws and wood screws. Working part. Dimensions

GOST R 52787-2007: Hinge and pliers tools. Technical requirements

GOST R 52796-2007: Empty enclosures for low-voltage switchgear and control gear assemblies. General requirements

GOST R 52797.1-2007: Acoustics. Recommended practice for the design of low-noise workplaces containing machinery. Part 1. Noise control strategies

GOST R 52797.2-2007: Acoustics. Recommended practice for the design of low-noise workplaces containing machinery. Part 2. Noise control measures

GOST R 52797.3-2007: Acoustics. Recommended practice for the design of low-noise workplaces containing machinery. Part 3. Sound propagation and noise prediction in workrooms

GOST R 52799-2007: Noise. Measurement of insertion loss of ducted silencers without flow. Laboratory survey method

GOST R 52800-2007: Noise. Coast-by methods for measurement of tyre-to-road sound emission

GOST R 52854-2007: Bolts with star-type head and small flange. Specifications

GOST R 52855-2007: Bolts with star-type head and large flange. Specifications

GOST R 52868-2007: Cable tray systems and cable ladder systems for cable management. General technical requirements and test methods

GOST R 52869-2007: Pneumatic drives. Safety requirements

GOST R 52894.1-2007: Noise of machines. Sound power rating of air-conditioning and air-source heat pump equipment. Part 1. Non-ducted outdoor equipment

GOST R 52894.2-2007: Noise of machines. Sound power rating of air-conditioning and air-source heat pump equipment. Part 2. Non-ducted indoor equipment

GOST R 52895-2007: Noise of machines. Acceptance test code gear units for airborne sound

GOST R 52908-2008: Thermal insulating products for building applications. Method for determination of organic content

GOST R 52941-2008: Passenger lifts. Planning and selection for residential buildings

GOST R 52942-2008: Railway applications. Axles. Product requirements.

GOST R 52953-2008: Thermal insulating materials and products. Terms and definitions

GOST R 52954-2008: Petroleum products. Determination of thermal oxidation stability of gas turbine fuels. JFTOT method

GOST R 52962-2008: Water. Methods for determination of chromium (VI) and total chromium

GOST R 52963-2008: Water. Methods for determination of alkalinity, and mass concentration of carbonates and hydrocarbonates

GOST R 52965-2008: Cylindrical shanks for milling cutters. Basic dimensions

GOST R 52966-2008: Subland twist drills for holes prior to tapping screw threads. Basic dimensions

GOST R 52967-2008: Dovetail slot single angle milling cutters. Dimensions

GOST R 52988-2008: Noise of machines. Reciprocating internal combustion engine driven alternating current generating sets. Measurement of airborne noise by the enveloping surface method

GOST R 52990.1-2008: Noise of machines. Textile machinery. Noise test code. Part 1. Common requirements

GOST R 53001-2008: Diamond and cubic boron nitride (elbow) tools. Safety requirements

GOST R 53002-2008: End mills with cylindrical, Morse taper and 7:24 taper shanks. Dimensions

GOST R 53003-2008: Slot drills with cylindrical, Morse taper and 7:24 taper shanks. Specifications

GOST R 53004-2008: T-slot cutters. Specifications

GOST R 53007-2008: Paint materials. Rapid deformation (impact resistance) test method

GOST R 53010-2008: Hydraulic presses. Safety requirements

GOST R 53032-2008: Noise of machines. Measurement of noise emitted by information technology and telecommunications equipment

GOST R 53037-2008: Mobile elevating work platforms. Design calculations, safety requirements, tests

GOST R 53065.1-2008: Refractory products with less than 45 % true porosity. Method for determination of compressive strength at room temperature. Part 1. Test without packings

GOST R 53073-2008: High-pressure sodium vapour lamps. Performance requirements

GOST R 53074-2008: High-pressure mercury vapour lamps. Performance requirements

GOST R 53075-2008: Metal halide lamps. Performance requirements

GOST R 53076-2008: Railway transport. Structural requirements of railway vehicle bodies

GOST R 53077-2008: Railway applications. Rules of designing and testing the bogie frame structures

GOST R 53080-2008: Vibration. Testing of mobile machinery in order to determine the vibration emission value. Industrial trucks

GOST R 53081-2008: Vibration. Assessment of exposure to hand-transmitted vibration using information on vibration emitted by machines

GOST R 53105-2008: Public catering service. Technological instructions for products of catering. General requirements for lay out, development and composition

GOST R 53106-2008: Public catering service. Method of calculation of wastes and losses of catering products

GOST R 53131-2008: Information protection. Guidelines for recovery services of information and communications technology security functions and mechanisms. General

GOST R 53148-2008: Rotating electrical machines. Noise limits

GOST R 53165-2008: Lead-acid storage starter batteries for motor-tractors. General specifications

GOST R 53166-2008: Influence of environmental conditions appearing in nature on the technical products. Overall performance. Earthquakes

GOST R 53188.1-2008: Sound level meters. Part 1. Technical requirements

GOST R 53188.2-2010: State system for ensuring the uniformity of measurements. Sound level meters. Part 2. Test methods

GOST R 53188.3-2010: State system for ensuring the uniformity of measurements. Sound level meters. Part 3. Verification procedure

GOST R 53189-2008: Environmental dynamic test methods for machines, instruments and other technical articles. Mixed mode vibration tests

GOST R 53190-2008: Environmental dynamic test methods for machines, instruments and other technical articles. Shock tests with shock response spectrum synthesis

GOST R 53199-2008: Ethanol fuel. Determination of ethanol content by method of gas chromatography

GOST R 53203-2008: Petroleum products. Determination of sulphur by method of wavelength dispersive X-ray fluorescence spectrometry

GOST R 53227-2008: Roofing, hydraulic-insulating, flexible, bitumen-based materials. Method for determination of deformation and strength properties

GOST R 53284-2009: Fire engineering. Generators of extinguishing aerosol. General technical requirements. Test methods

GOST R 53285-2009: Fire engineering. Portable generators of extinguishing aerosol. General technical requirements. Test methods

GOST R 53292-2009: Fire retardant compositions and substances for wood. General requirements. Test methods

GOST R 53334-2009: Vacuum equipment. Vapour vacuum pumps. Measurement of performance characteristics. Part 1. Measurement of volume rate of flow (pumping speed)

GOST R 53335-2009: Vacuum equipment. Positive-displacement vacuum pumps. Measurement of performance characteristics. Part 1. Measurement of volume rate of flow (pumping speed)

GOST R 53354-2009: Cables and their accessories. Impulse tests

GOST R 53362-2009: Electromagnetic compatibility of technical equipment. Uninterruptible power systems. Requirements and test methods

GOST R 53366-2009: Steel pipes for use as casing or tubing for wells in petroleum and natural gas industries. General specifications

GOST R 53376-2009: Sound absorbing materials. Sound absorption measurement method in reverberation room

GOST R 53377-2009: Sound absorbing materials used in buildings. Assessment of sound absorption

GOST R 53378-2009: Acoustical materials used in floating floors of residential buildings. Method for determination of dynamic stiffness

GOST R 53387-2009: Lifts, escalators and moving walks. Risk assessment and reduction methodology

GOST R 53388-2009: Lifts. Control devices, signals and additional fittings

GOST R 53395-2009: Health informatics. Basic regulations

GOST R 53411-2009: Saw blades for metal cutting. Specifications

GOST R 53412-2009: Woodruff keyseat cutters. Specifications

GOST R 53413-2009: End mills with brazed helical hard metal tips. Basic dimensions

GOST R 53414-2009: End mills with brazed helical hard metal tips with 7:24 taper shank. Basic dimensions

GOST R 53415-2009: Water. Sampling for microbiological analysis

GOST R 53440-2009: Basic norms of interchangeability. Geometrical product specifications. Standard rates of taper and cone angles

GOST R 53442-2009: Basic norms of interchangeability. Geometrical product specifications. Tolerances of form, orientation, location and run-out

GOST R 53453-2009: Ergonomics of the thermal environment. Application of requirements of standards to people with special requirements

GOST R 53454.1-2009: Ergonomic procedures for the improvement of local muscular workloads. Part 1. Guidelines for reducing local muscular workloads

GOST R 53455-2009: Roofing, hydraulic-insulating, flexible, bitumen-based materials. Method for determination of resistance to tearing (nail shank)

GOST R 53479-2009: Printing trades equipment. Methods for determination of noise emission dates. Accuracy grades 2 and 3

GOST R 53481-2009: Lubrication systems. Safety requirements

GOST R 53569-2009: Noise of machines. Noise test code for fastener driving tools. Engineering method

GOST R 53570-2009: Acoustics. Noise from shooting ranges. Part 1. Determination of acoustic characteristics of muzzle blast by measurement

GOST R 53571-2009: Acoustics. Noise from shooting ranges. Part 2. Estimation acoustic characteristics of muzzle blast and projectile sound by calculation

GOST R 53572-2009: Acoustics. Noise from shooting ranges. Part 4. Prediction projectile sound

GOST R 53573-2009: Mechanical vibration. Measurement of vibration transferred into resilient isolators. General requirements

GOST R 53574-2009: Noise. Assessment of noise annoyance by means of social and socio-acoustic surveys

GOST R 53577-2009: Mechanical vibration. Measurement of vibration transferred into resilient isolators. High-speed and medium-speed reciprocating internal combustion engines

GOST R 53581-2009: Gasoline. Determination of the phosphorus content

GOST R 53604-2009: Conformity assessment. National Standards System in Conformity Assessment

GOST R 53613-2009: Classification overall performance of influence of environmental conditions appearing in nature on the technical products. Precipitation and wind

GOST R 53615-2009: The influence of environmental conditions appearing in nature on the technical products. Overall performance. Solar radiation and temperature

GOST R 53634-2009: Gas-fired central heating boilers, type B boilers, of nominal heat input exceeding 70 kW, but not exceeding 300 kW. General technical requirements and test methods

GOST R 53636-2009: Pulp, paper, board. Terms and definition

GOST R 53646-2009: Noise of machines. Measurement of airborne sound emitted by powered small recreational craft

GOST R 53647.4-2011: Business continuity management. Guideline for incident preparedness and operational continuity management

GOST R 53651-2009: Paint materials. Method for determination of the effect of heat

GOST R 53652.1-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 3. General requirement

GOST R 53652.2-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 2. Pipes made of unplasticized poly(vinyl chloride), chlorinated poly(vinyl chloride) and high impact poly(vinyl chloride)

GOST R 53652.3-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 3. Polyolefin pipes

GOST R 53653-2009: Paint materials. Method for determination of the pot life of multicomponent systems

GOST R 53654.1-2009: Paint materials. Method for determination of density. Part 1. Pyknometer method

GOST R 53656.2-2009: Plastics. Determination of gas-transmission rate. Part 2. Equal-pressure method

GOST R 53660-2009: Ships and marine technology. Port facility security assessments and security plan development

GOST R 53661-2009: Security management system for the supply chain. Guidelines for the implementation

GOST R 53662-2009: Security management systems for the supply chain. Best practices for implementing supply chain security. Assessments and plans

GOST R 53663-2009: Requirements specification for security management system for the supply chain

GOST R 53706-2009: Aviation fuels. Method of freezing point determination

GOST R 53714-2009: Motor fuels, aviation fuels and low-boiling distillates. Method for determination of existent gums by jet evaporation

GOST R 53715-2009: Aviation turbine fuels. Method for determination of lubricity by the ball-on-cylinder lubricity evaluator (BOCLE)

GOST R 53716-2009: Fuel oils. Determination of hydrogen sulphide

GOST R 53717-2009: Petroleum products. Test method for flash point by Tag closed cup tester

GOST R 53718-2009: Aviation fuels. Method of smoke point determination

GOST R 53734.2.3-2010: Electrostatics. Part 2.3. Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation

GOST R 53734.4.1-2010: Electrostatics. Part 4.1. Test methods for specific applications. Electrical resistance of floor covering and installed floors

GOST R 53734.4.5-2010: Electrostatics. Part 4-5. Standard test methods for specific applications. Methods for characterizing the electrostatic protection of footwear and flooring in combination with a person

GOST R 53735.5-2009: Surge arresters without gaps and non-linear resistor type gapped surge arresters for a.c. electrical installations for voltages from 3 to 750 kV. Part 5. Selection and application recommendations

GOST R 53737-2009: Petroleum and natural gas industries. Reciprocating compressors. General technical requirements

GOST R 53770-2010: Passenger lifts. Basic parameters and dimensions

GOST R 53771-2010: Goods lifts. Basic parameters and dimensions

GOST R 53910-2010: Water. Methods of toxicity determination by growth inhibition of marine unicellular algae Phaeodactylum tricornutum Bohlin and Sceletonema costatum (Greville) Cleve

GOST R 53922-2010: Diamond and from cubic boron nitride (elbon) powders. Grain and grain size distribution of grinding powders. Test of grain size distribution

GOST R 53925-2010: Pliers and nippers. General technical requirements, methods of control, tests

GOST R 53926-2010: End milling cutters with shell-type inserted blades for woodcutting. General specifications

GOST R 53927-2010: Shell-type inserted blade circular cutterbloks for woodcutting. General specifications

GOST R 53935-2010: Screwdrivers for fitting and assembling for recessed screws and wood screws. General technical requirements, methods of control and tests

GOST R 53936-2010: Shank-type milling cutters of solid and tipped design. Symbols

GOST R 53937-2010: Shank-type milling cutters with indexable inserts. Symbols

GOST R 53984-2010: Mobile elevating work platforms. Safety principles and inspection of technical operational state

GOST R 53986-2010: Reciprocating internal combustion engine driven alternating current generating sets. Part 3. Alternating current generators

GOST R 54013-2010: Hydraulic fluid power. Impact of changes in ISO fluid power particle counting. Contamination control and filter test standards

GOST R 54025-2010: Chayka Radionavigation System. Receivers. Specification Requirements. Methods of testing and required test results

GOST R 54061-2010: Railway applications. Acoustics. Measurement of noise emitted by railbound vehicles

GOST R 54081-2010: Influence of environmental conditions appearing in nature on the technical products. Overall performance. Fire

GOST R 54082-2010: Requirements for performance of chambers for industrial products environmental endurance tests. Data processing methods for chamber certification (calibration)

GOST R 54083-2010: General requirements for performance of chambers for industrial products environments endurance tests. Certification methods for chambers (with load) for temperature resistance test

GOST R 54104-2010: Perspective industrial technologies. Classification and conformity assessment of products, processes and services for petroleum and natural gas industries

GOST R 54105-2010: Polymeric films and sheeting. Method for determination of wetting tension

GOST R 54106-2010: Polymeric films and sheeting. Method for determination of dimensional change on heating

GOST R 54127-1-2010: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 1. General requirements

GOST R 54127-2-2011: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 2. Insulation resistance

GOST R 54127-3-2011: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 3. Loop impedance

GOST R 54127-4-2011: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 4. Resistance of earth connection and equipotential bonding

GOST R 54127-5-2011: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 5. Resistance to earth

GOST R 54148-2010: Human exposure to electromagnetic fields from household and similar electrical appliances. Methods for evaluation and measurement

GOST R 54165-2010: Glass and glass products. Thermal properties determination methods. Thermal resistance determination method

GOST R 54166-2010: Glass and glass products. Thermal properties determination methods. Thermal resistance calculation method

GOST R 54167-2010: Glass and glass products. Determination of energy balance value. Calculation method

GOST R 54173-2010: Sealed insulating glass units. Methods for determining the physical attributes of edge seals

GOST R 54174-2010: Sealed insulating glass units. Rules and methods of products quality assurance

GOST R 54239-2010: Solid mineral fuels. Selection of methods for the determination of trace elements

GOST R 54242-2010: Solid mineral fuel. Determination of total arsenic and selenium content

GOST R 54244-2010: Solid mineral fuel. Instrumental method for determination of carbon, hydrogen and nitrogen

GOST R 54267-2010: Ethanol, denatured fuel ethanol and fuel ethanol (Ed75-Ed85). Method for determination of pH

GOST R 54268-2010: Aviation fuels and petroleum distillates. Determination of aromatic hydrocarbon types by high performance liquid chromatography method with refractive index detection

GOST R 54269-2010: Fuels. Method of determination for cold filter plugging point

GOST R 54273-2010: Petroleum and petroleum products. Guide for use of the measurement tables

GOST R 54274-2010: Aviation fuels. Determination of particulate contamination by laboratory filtration method

GOST R 54276-2010: Water. Methods for determination of copper

GOST R 54277-2010: Fuel ethanol. Determination of total and potential sulphates and inorganic chlorides by method of direct injection suppressed ion chromatography

GOST R 54279-2010: Petroleum products. Methods for determination of flash point in Pensky-Martens closed cup tester

GOST R 54280-2010: Aviation fuels. Determination of freezing point by automatic laser method

GOST R 54281-2010: Petroleum products, lubricating oils and additives. Test method for determination of water by coulometric Karl Fischer titration

GOST R 54282-2010: Gasoline. Determination of oxygenates by method of gas chromatography and oxygen selective flame ionization detection

GOST R 54284-2010: Crude oil. Determination of water by coulometric Karl Fischer titration

GOST R 54285-2010: Gasoline and methanol fuels. Determination of total oxygen content by methods of reductive pyrolysis

GOST R 54286-2010: Residual fuel oils. Method for measurement of hydrogen sulphide in the vapour phase

GOST R 54287-2010: Fuel ethanol. Determination of total and potential inorganic sulphates and total inorganic chlorides by method of ion chromatography using aqueous sample injection

GOST R 54288-2010: Light liquid petroleum hydrocarbons. Determination of trace quantities of sulphur by oxidative microcoulometry

GOST R 54289-2010: Diesel fuels. Method for determination of filterability by low-temperature flow test (LTFT)

GOST R 54290-2010: Fuel ethanol (Ed75-Ed85) for automotive spark-ignition engines. Specifications

GOST R 54291-2010: Crude petroleum. Gas chromatography method for determination of components boiling temperature range distribution

GOST R 54299-2010: Marine fuels. Specifications

GOST R 54303-2011: Roofing and hydraulic-insulating flexible bitumen-based materials. Method for determination of peel resistance of joints

GOST R 54304-2011: Roofing and hydraulic-insulating flexible bitumen-based materials. Method for determination of shear resistance of joints

GOST R 54327-2011: Glass and glazing. Sound insulation determination method

GOST R 54331-2011: Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear. Specifications

GOST R 54360-2011: Laboratory information management systems (LIMS). Standard guide for validation of LIMS

GOST R 54370-2011: Explosive atmospheres. Quality management system of requirement manufacturer. Requirements

GOST R 54371-2011: Safety in electric heating installations. Part 9. Particular requirements for high-frequency dielectric heating installations

GOST R 54372-2011: Safety in electric heating installations. Part 6. Specifications for safety in industrial microwave heating equipment

GOST R 54381-2011: Refrigerant compressors. Rating conditions, tolerances and presentation of manufacturer’s performance data

GOST R 54382-2011: Oil and gas industry. Submarine pipeline systems. General requirements

GOST R 54383-2011: Steel drill pipes for petroleum and natural gas industries. Specifications

GOST R 54384-2011: Steel. Definition and classification by chemical composition and classes of quality

GOST R 54418.12.1-2011: Wind turbines. Power performance measurements of electricity producing wind turbines

GOST R 54418.21-2011: Renewable power engineering. Wind power engineering. Wind turbines. Part 21. Measurement and assessment of power quality characteristics of grid connected wind turbines

GOST R 54428-2011: Technical energy systems. Methods for analysis. Part 1. Basic principles

GOST R 54434-2011: Railway application. Rolling stock equipment. Shock and vibration

GOST R 54438-2011: Gas-fired central heating boilers. Additional requirements for the domestic water heaters jointly with boilers of nominal heat input not exceeding 70 kW

GOST R 54439-2011: Gas fired central heating boilers. Type B boilers of nominal heat input not exceeding 300 kW, but not exceeding 1000 kW

GOST R 54440-2011: Heating boilers. Part 1. Heating boilers with forced draught burners. Terminology, general requirements, test and marking

GOST R 54441-2011: Heating boilers. Part 2. Heating boilers with forced draught burner. Special requirements for boilers with atomizing oil burners

GOST R 54442-2011: Heating boilers. Part 3. Gas-fired central heating boilers. Assembly comprising boiler body and a forced draught burner. Testing of heat engineering

GOST R 54448-2011: Single burner gas-fired overhead radiant tube heaters for non-domestic use. Part 1. Safety requirements

GOST R 54455-2011: Alarm systems. Environmental test methods

GOST R 54467-2011: Thick building materials and products of high and medium thermal resistance. Methods for determination of thermal resistance by means of guarded hot plate and heat flow meter

GOST R 54469-2011: Building materials and products of high and medium thermal resistance. Methods of determination of thermal resistance by means of guarded hot plate and heat flow meter

GOST R 54471-2011: Document management. Information stored electronically. Recommendations for trustworthiness and reliability

GOST R 54482-2011: Piping connections for general-use hydraulic fluid power. Hose fittings with metric stud ends and O-ring. Technical requirements

GOST R 54483-2011: Oil and gas industry. Offshore platforms for oil and gas production. General requirements

GOST R 54485-2011: Electromagnetic compatibility of technical equipment. Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz. Part 2-1. Main communications equipment and systems operating in the range of frequencies 95 kHz to 148,5 kHz intended for use in residential, commercial and light industrial environments. Immunity requirements and test methods

GOST R 54488-2011: Adjustable wrenches. Specifications

GOST R 54489-2011: Circular saws for cutting logs machines and automatic lines. General technical requirements

GOST R 54490-2011: Superhard tipped circular saws for machining wood materials and plastics. General specifications

GOST R 54496-2011: Water. The determination of toxicity with use of green freshwater unicellular algae

GOST R 54500.1-2011: Uncertainty of measurement. Part 1. Introduction to guides on uncertainty in measurement

GOST R 54532-2011: Resources saving. Waste treatment. Waste classification and management in footwear manufacturing

GOST R 54533-2011: Resources saving. Waste management. Guidelines and methods for the recovery of plastics waste

GOST R 54546-2011: Rubber synthetic. Determination of volatile matter content

GOST R 54548-2011: Isoprene rubber (IR). Preparation and testing of rubber compounds

GOST R 54550-2011: Synthetic rubbers. Determination of the mass fraction of extractables

GOST R 54555-2011: Styrene-butadiene rubber (SBR). Preparation and testing of rubber compounds

GOST R 54556-2011: Acrylonitrile-butadiene rubbers (NBR). Preparation and testing of rubber compounds

GOST R 54557-2011: Isobutene-isoprene rubber (IIR). Preparation and testing of rubber compounds

GOST R 54558-2011: Solution-polymerized butadiene rubber (BR). Preparation and testing of rubber compounds

GOST R 54563-2011: Paint materials. Determination of adhesive by cross-cut method

GOST R 54586-2011: Paint materials. Method for determination of paint film hardness by pencil test

GOST R 54765-2011: Escalators and moving walks. Safety requirements for construction and installation

GOST R 54769-2011: Cranes. General requirements for stability

GOST R 54792-2011: Imperfections in thermoplastic welding joint. Description and evaluation

GOST R 54801-2011: Traction transformers and inductors on board railway rolling stock. Basic parameters and test methods

GOST R 54805-2011: Centrifugal pumps. Technical specifications. Class II

GOST R 54806-2011: Centrifugal pumps. Technical specifications. Class I

GOST R 54813-2011: Electric cables, wires and cords. Spark test method

GOST R 54814-2011: Light emitted diodes and light emitting diode modules for general application. Terms and definitions

GOST R 54815-2011: Self-ballasted LED-lamps for general lighting services by voltage over 50 V. Operating requirements

GOST R 54827-2011: Dry-type transformers. General specifications

GOST R 54853-2011: Bulidings and structures. Method for determination of thermal resistance and thermal coefficient of enclosing structures with assistance of heat flow meter

GOST R 54856-2011: Heat supply of buildings. Methods for calculating systems energy requirements and system efficiencies for heat generation systems with solar systems

GOST R 54860-2011: Heat supply of buildings. General guidelines of methods for calculation of energy requirements and efficiencies for heat supply systems

GOST R 54863-2011: Shutters and blinds. Additional thermal resistance determination

GOST R 54865-2011: Heat supply of buildings. Method for calculation of energy requirements and efficiencies for of heat generation with heat pump systems

GOST R 54866-2011: Thermoplastics pipes. Determination of the long-term hydrostatic strength on pipe samples by extrapolation method

GOST R 54867-2011: Multilayer plastics pipes. Determination of the long-term strength

GOST R 54908-2012: Heat-resistant steel metal products. Specifications

GOST R 54909-2012: Metal products from alloyed steel and alloys for valves of internal combustion engines. Specifications

GOST R 54963-2012: Reinforcing alkali-resistant glass fibre meshes for building faces. Method for determination of the mechanical properties

GOST R 54970-2012: Food processing machinery. Centrifugal devices for drying vegetables and fruits. Safety and hygiene requirements

GOST R 54985-2012: Guidelines for small businesses on implementation of quality management system based on ISO 9001:2008

GOST R 54986-2012: Low voltage surge protective devices. Part 21. Surge protective devices connected to telecommunications and signalling networks. Performance requirements and testing methods

GOST R 54999-2012: Lifts. General Requirements for maintenance instruction

GOST R 55026-2012: Design of fans working in potentially explosive atmospheres

GOST R 55061-2012: Electromagnetic compatibility of technical equipment. Static transfer system. Part 2. Requirements and test methods

GOST R 55139-2012: Electromagnetic compatibility of technical equipment. Resistance welding equipment. Part 2. Requirements and test methods

GOST R 55236.2-2012: Ergonomics of everyday products. Part 2. Test method for walk-up-and-use products

GOST R 55266-2012: Electromagnetic compatibility of technical equipment. Telecommunication network equipment. Requirements and test methods

GOST R 55390-2012: System of national standards for quality of telecommunication services. Structure and composition

GOST R 55416-2013: Nanotechnologies. Part 1. Core terms and definitions

GOST R 55684-2013: Drinking water. Methods for the determination of permanganate index

GOST R 55942-2014: Steel tubes. Preparation of ends of tubes and fittings for welding. General technical requirements

GOST R 7.0.0-2010: System of standards on information, librarianship and publishing. National system of standards on information, librarianship and publishing. Main principles

GOST R 7.0.11-2011: System of standards on information, librarianship and publishing. Dissertation and dissertation abstract. Structure and rules of presentation

GOST R 7.0.8-2013: System of standards on information, librarianship and publishing. Records management and organization of archives. Terms and definitions

GOST R 8.563-96: State system for ensuring the uniformity of measurements. Procedures of measurements

GOST R 8.595-2004: State system for ensuring the uniformity of measurements. Mass of petroleum and petroleum products. General requirements for procedures of measurements

GOST R 8.613-2005: State system for ensuring the uniformity of measurements. Procedures for quantitative chemical analysis of water samples. General requirements for development

GOST R 8.626-2006: State system for ensuring the uniformity of measurements. Saccharine confectionery. Infrared thermogravimetric method of moisture content determination

GOST R 8.633-2007: State system for ensuring the uniformity of measurements. Cereals and cereal products. Infrared thermogravimetric method of moisture content determination

GOST R 8.634-2007: State system for ensuring the uniformity of measurements. Oilseeds and oilseeds residues. Infrared thermogravimetric method of moisture content determination

GOST R 8.662-2009: State system for ensuring the uniformity of measurements. Natural gas. Gas phase thermodynamic properties. Methods of calculation for transmission and distribution applications on base of the AGA8 fundamental equation of state

GOST R 8.694-2010: State system for ensuring the uniformity of measurements. Standard reference materials (substances). General statistical principles of determination of metrological characteristics

GOST R 8.695-2009: State system for ensuring the uniformity of measurements. Metals and alloys. Vickers hardness test. Part 2. Verification and calibration of testing machines

GOST R 8.714-2010: State system for ensuring the uniformity of measurements. Octave-band and fractional-octave-band filters. Technical requirements and test methods

GOST R 8.747-2011: State system for ensuring the uniformity of measurements. Metals and alloys. Vickers hardness test. Part 3. Calibration of reference block

GOST R 8.748-2011: State system for ensuring the uniformity of measurements. Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 1. Test method

GOST R 8.769-2011: State system for ensuring the uniformity of measurements. Natural gas. Compression factor of gas phase. Method of calculation based on gas physical properties

GOST R 8.785-2012: State system for ensuring the uniformity of measurements. Mass of hydrocarbon condensate, liquefied hydrocarbon gas and long distillate of light hydrocarbons. General requirement for procedure (methods) of measurements

GOST R 9.317-2010: Unified system of corrosion and ageing protection. Metallic coatings. Methods of measurement of ductility

GOST R 9.901.3-2007: Unified system of corrosion and ageing protection. Metals and alloys. General requirements for U-bend specimens of stress corrosion testing

GOST R 9.905-2007: Unified system of corrosion and ageing protection. Corrosion test methods. General requirements

GOST R 9.907-2007: Unified system of corrosion and ageing protection. Metals, alloys, metallic coatings. Methods for removal of corrosion products after corrosion tests

GOST R 9.915-2010: Unified system of corrosion and ageing protection. Metals, alloys, coatings, products. Test methods of hydrogen embrittlement

GOST R EN 1010-1-2009: Printing machinery. Safety requirements for the design and construction. Part 1. General requirements

GOST R EN 1010-3-2009: Printing machinery. Safety requirements for the design and construction. Part 3. Cutting machines

GOST R EN 1107-1-2008: Roofing, hydraulic-insulating, flexible, bitumen-based materials. Method for determination of linear dimensional change

GOST R EN 1108-2011: Roofing and hydraulic-insulating flexible bitumen-based materials. Method for determination of form stability under cyclical temperature changes

GOST R EN 1109-2009: Roofing, hydraulic-insulating, flexible, bitumen-based materials and polymeric (thermoplastic or elastomer) materials. Method determination of water tightness

GOST R EN 1110-2008: Roofing and hydraulic-insulating flexible bitumen-based materials. Method for determination of heat resistance

GOST R EN 1127-2-2009: Explosive atmospheres. Explosion prevention and protection. Part 2. Basic concepts and methodology for mining

GOST R EN 12039-2008: Roofing, hydraulic-insulating, flexible, bitumen-based materials. Method for determination of granules to coating layer adhesion

GOST R EN 12083-2011: Occupational safety standards system. Respiratory protective devices. Filters with breathing hoses (filters with hoses). Particle filters, gas filters and combined filters. Requirements, testing, marking

GOST R EN 12085-2008: Thermal insulating products for applications in building. Methods for measurement of linear dimensions of test specimens

GOST R EN 12086-2008: Thermal insulating products in building applications. Method for determination of water vapour transmission properties

GOST R EN 12087-2008: Thermal insulating products for building applications. Methods for determination of long term water absorption by immersion

GOST R EN 12088-2010: Thermal insulating products in building applications. Method for determination of long-term moisture absorption by diffusion

GOST R EN 12089-2008: Thermal insulating products for building applications. Method for determination of bending behaviour

GOST R EN 12090-2008: Thermal insulating products for building applications. Method for determination of shear behaviour

GOST R EN 12091-2010: Thermal insulating products in building applications. Method for determination of freeze-thaw resistance

GOST R EN 12177-2008: Liquid petroleum products. Petroleum. Determination of benzene content by method of gas chromatography

GOST R EN 12430-2008: Thermal insulating products for building applications. Method for determination of behaviour under point load

GOST R EN 12431-2008: Thermal insulating products used in building for floating floors. Method for measurement of thickness

GOST R EN 12717-2006: Safety of machine tools. Drilling machines

GOST R EN 12840-2006: Safety of machine-tools. Manually controlled turning machines with or without automatic control

GOST R EN 12841-2012: Occupational safety standards system. Personal protective equipment against falls from a height. Rope access systems. Rope adjustment devices. General technical requirements. Test methods

GOST R EN 12942/A1/A2-2010: Occupational safety standards system. Respiratory protective devices. Power assisted filtering devices incorporating full face masks, half masks or quarter masks. General technical requirements. Test methods. Marking

GOST R EN 12952-1-2012: Water-tube boilers and auxiliary installations. Part 1. General. Wasserrohrkessel und Anlagenkomponenten. Teil 1. Allgemeine bestimmungen

GOST R EN 12957-2007: Safety of metal-working machine tools. Electrodisharge machines

GOST R EN 1296-2011: Roofing and hydraulic-insulating flexible bitumen-based materials and polymeric (thermoplastic or elastomer) materials. Method of artificial ageing by long-term exposure to elevated temperature

GOST R EN 13016-1-2008: Liquid petroleum products. Part 1. Determination of air saturated vapour pressure (ASVP)

GOST R EN 13218-2006: Safety of machine-tools. Stationary grinding machines

GOST R EN 13274-1-2009: Occupational safety standards system. Respiratory protective devices. Methods of test. Part 1. Determination of inward leakage and total inward leakage

GOST R EN 13274-6-2011: Occupational safety standards system. Respiratory personal protective devices. Methods of test. Part 6. Determination of carbon dioxide content of the inhalation air

GOST R EN 13274-7-2009: Occupational safety standards system. Respiratory protective devices. Methods of test. Part 7. Determination of particle filter penetration

GOST R EN 13274-8-2009: Occupational safety standards system. Respiratory protective devices. Test methods. Part 8. Determination of dolomite dust clogging

GOST R EN 13416-2008: Roofing, hydraulic-insulating, flexible, bitumen-based materials and polymeric (thermoplastic or elastomer) materials. Rules for sampling

GOST R EN 13463-1-2009: Non-electrical equipment for potentially explosive atmospheres. Part 1. Basic method and requirements

GOST R EN 13463-3-2009: Non-electrical equipment for potentially explosive atmospheres. Part 3. Protection by flameproof enclosure «d»

GOST R EN 13463-5-2009: Non-electrical equipment for potentially explosive atmospheres. Part 5. Protection by constructional safety “c”

GOST R EN 13788-2007: Safety of metal-working machine tools. Multi-spindle automatic turning machines

GOST R EN 13819-2-2011: Occupational safety standards system. Personal hearing protectors. Acoustic test methods

GOST R EN 13897-2011: Roofing and hydraulic-insulating flexible, bitumen-based materials and polymeric (thermoplastic or elastomer) materials. Method for determination of water tightness after stretching at low temperature

GOST R EN 14078-2010: Liquid petroleum products. Determination of fatty acid methyl esters (FAME) in middle distillates by infrared spectroscopy method

GOST R EN 14130-2010: Foodstuffs. Determination of vitamin C by HPLC

GOST R EN 14331-2010: Liquid petroleum products. Separation and characterization of fatty acid methyl esters (FAME) from middle distillates by method of liquid chromatography and gas chromatography

GOST R EN 14594-2011: Occupational safety standards system. Respiratory protective devices. Continuous flow compressed air line breathing apparatus. Requirements, testing, marking

GOST R EN 1497-2012: Occupational safety standards system. Personal protective equipment against falls from a height. Rescue harness. General technical requirements. Test methods

GOST R EN 1498-2012: Occupational safety standards system. Personal fall protection equipment. Rescue loops. General technical requirements. Test methods

GOST R EN 15195-2011: Liquid petroleum products. Middle distillate fuels. Method for determination of ignition delay and derived certain number (DCN) by combustion in a constant volume chamber

GOST R EN 15565-2012: Tourist services. Requirements for the provision of professional tourist guide training and qualification programmes

GOST R EN 1601-2007: Liquid petroleum products. Unleaded petrol. Determination of organic oxygenate compounds and total organically bound oxygen content by gas chromatography method using the oxygen flame-ionization detector (O-FID)

GOST R EN 1602-2008: Thermal insulating products for building applications. Method for determination of the apparent density

GOST R EN 1604-2008: Thermal insulating products for building applications. Method for determination of dimensional stability under specified temperature and humidity conditions

GOST R EN 1605-2010: Thermal insulating products for building applications. Method for determination of deformation under specified compressive load and temperature conditions

GOST R EN 1606-2010: Thermal insulating products in building applications. Method for determination of compressive creep

GOST R EN 1607-2008: Thermal insulating products for building applications. Method for determination of tensile strength perpendicular to faces

GOST R EN 1608-2008: Thermal insulating products for building applications. Method for determination of tensile strength parallel to faces

GOST R EN 1609-2008: Thermal insulating products for building applications. Method for determination of water absorption by short term and partial immersion

GOST R EN 1827-2009: Occupational safety standards system. Respiratory protective devices - Half masks without inhalation valves and with separable filters to protect against gases or gases and particles or particles only. Requirements. Testing. Marking

GOST R EN 1834-1-2010: Reciprocating internal combustion engines. Safety requirements for engines, intended for use in potentially explosive atmospheres. Part 1. Group II engines for use in flammable gas and vapour atmospheres

GOST R EN 1834-2-2010: Reciprocating internal combustion engines. Safety requirements for engines, intended for use in potentially explosive atmospheres. Part 2. Group I engines for use in underground workings susceptible to fired amp and/or combustible dust

GOST R EN 1834-3-2010: Reciprocating internal combustion engines. Safety requirements for engines, intended for use in potentially explosive atmospheres. Part 3. Group III engines for use in flammable dust atmospheres

GOST R EN 1848-1-2008: Roofing, hydraulic-insulating flexible bitumen-based materials. Methods for determination of length, width and straightness

GOST R EN 1849-1-2009: Roofing, hydraulic-insulating, flexible, bitumen-based materials. Methods for determination of thickness and mass per unit area

GOST R EN 1850-1-2008: Roofing and hydraulic-insulating flexible bitumen-based materials. Method for determination of visual defects

GOST R EN 1850-2-2008: Roofing and hydraulic-insulating flexible polymeric (thermoplastic or elastomer) materials. Method for determination of visual defects

GOST R EN 1891-2012: Occupational safety standards system. Personal protective equipment against falls from a height. Low stretch kernmantel ropes. General technical requirements. Test methods

GOST R EN 1928-2009: Roofing, hydraulic-insulating, flexible, bitumen-based materials and polymeric (thermoplastic or elastomer) materials. Method determination of water tightness

GOST R EN 1986-2-2011: Electrically propelled road vehicles. Measurement of energy performances. Part 2. Hybrid vehicles

GOST R EN 237-2008: Liquid petroleum products. Determination of low lead concentrations by atomic absorption spectrometry

GOST R EN 29053-2008: Acoustical materials. Methods for determination of airflow resistance

GOST R EN 308-2011: Heat exchangers. Test methods for determining the power criteria of air/air and an air/exhaust gas mixture heat recovery devices

GOST R EN 340-2010: Occupational safety standards system. Protective clothing. General technical requirements

GOST R EN 341-2010: Occupational safety standards system. Personal protective equipment against falls from a height. Descender devices. General technical requirements. Test methods

GOST R EN 353-1-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Guided type fall arresters including a rigid anchor line. Part 1. General technical requirements. Test methods

GOST R EN 353-2-2007: Occupational safety standards system. Guided type fall arresters including a flexible anchor line. Part 2. General technical requirements. Test methods

GOST R EN 354-2010: Occupational safety standards system. Personal protective equipment against falls from a height. Lanyard. General technical requirements. Test methods

GOST R EN 355-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Energy absorbers. General technical requirements. Test methods

GOST R EN 358-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Belts and lanyards for work positioning and restraint. General technical requirements. Test methods

GOST R EN 360-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Retractable type fall arresters. General technical requirements. Test methods

GOST R EN 361-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Full body harnesses. General technical requirements. Test methods

GOST R EN 362-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Connectors. General technical requirements. Test methods

GOST R EN 363-2007: Occupational safety standards system. Personal protective equipment against falls from a height. Fall arrest systems. General technical requirements

GOST R EN 365-2010: Occupational safety standards system. Personal protective equipment against falls from a height. General requirements for instructions for use, maintenance, periodic examination, repair, marking and packaging

GOST R EN 374-2009: Occupational safety standards system. Personal protection of hands. Protective gloves against chemicals and micro-organisms. General technical requirements. Methods of testing

GOST R EN 379-2011: System of standards for occupational safety. Personal eye and face protection equipment during welding and related processes. Automatic welding filters. General specifications

GOST R EN 397/A1-2010: Occupational safety standards system. Safety helmets. General technical requirements. Test methods

GOST R EN 404-2011: Occupational safety standards system. Respiratory protective devices for self-rescue. Filter self-rescuer from carbon monoxide with mouthpiece assembly. General specifications

GOST R EN 407-2009: Occupational safety standards system. Personal protective means of hands. Protective gloves from heat thermal and fire. Technical requirements. Test methods

GOST R EN 414-2002: Safety of machinery. Rules for the drafting and presentation of safety standards

GOST R EN 464-2007: Occupational safety standards system. Protective clothing for use against liquid and gaseous chemicals, including aerosols and solid particles. Method for determination of leak-tightness of gas-tight suits

GOST R EN 50194-2008: Electrical apparatus for the detection of combustible gases in domestic premises. General requirements and control methods

GOST R EN 511-2010: Occupational safety standards system. Personal protective means of hands. Protective gloves against cold. General technical requirements. Test methods

GOST R EN 813-2008: Occupational safety standards system. Personal protective equipment against falls from a height. Sit harnesses. General technical requirements. Test methods

GOST R EN 822-2008: Thermal insulating products for building applications. Methods for measurement of length and width

GOST R EN 823-2008: Thermal insulating products for building applications. Methods for measurement of thickness

GOST R EN 824-2008: Thermal insulating products for building applications. Methods for measurement of deviation from squareness

GOST R EN 825-2008: Thermal insulating products for building applications. Methods for measurement of deviation from flatness

GOST R EN 826-2008: Thermal insulating products for building applications. Methods for determination of compression behaviour

GOST R EN 9100-2011: Quality management systems of organizations of aviation, space and defence industries. Requirements

GOST R EN 9101-2011: Quality management systems of organizations of aviation, space and defence industries. Assessment of quality management systems

GOST R EN 9110-2011: Quality management systems. Requirements for aviation maintenance organizations

GOST R EN 9120-2011: Quality management systems of organizations of aviation, space and defence industries. Requirements for distributors of production

GOST R EN ISO 12205-2007: Petroleum products. Determination of the oxidation stability of distillate fuels

GOST R EN ISO 13982-1-2009: Occupational safety standards system. Protective clothing for use against solid particulates. Part 1. Performance requirements for chemical protective clothing providing protection to full body against airborne solid particulates (type 5 clothing)

GOST R EN ISO 13982-2-2009: Occupational safety standards system. Protective clothing for use against solid particulates. Part 2. Test method of determination of inward leakage of aerosols of fine particles into suits

GOST R EN ISO 20345-2011: Occupational safety standards system. Feet personal protective means. Safety footwear. Technical requirements

GOST R EN ISO 20846-2006: Petroleum products. Determination of sulfur content by ultraviolet fluorescence method

GOST R EN ISO 20847-2010: Petroleum products. Determination of sulphur content in automotive fuels by energy-dispersive X-ray fluorescence spectrometry

GOST R EN ISO 22854-2010: Liquid petroleum products. Аutomotivemotor gasolines. Determination of hydrocarbon types and oxygenates by method of multidimensional gas chromatography

GOST R EN ISO 2719-2008: Petroleum products. Methods for determination of flash point in Pensky-Martens closed cup

GOST R EN ISO 3405-2007: Petroleum products. Method for determination of distillation characteristics at atmospheric pressure

GOST R EN ISO 7536-2007: Gasolines. Determination of oxidation stability. Induction period method

GOST R IEC 60034-14-2008: Electric rotating machines. Part 14. Mechanical vibration of certain types of machines with a rotation axis height of 56 mm or more. Measurements, assessment and limits of vibration

GOST R IEC 60034-5-2007: Rotating electrical machines. Part 5. Classification of protection degrees provided by the integral design of rotating electrical machines (IP code)

GOST R IEC 60050-195-2005: Earthing and protection against electric shock. Terms and definitions

GOST R IEC 60079-35-1-2011: Caplights for use in mines susceptible to firedamp. Part 1. General requirements and test methods in relation to the risk of explosion

GOST R IEC 60095-2-2010: Lead-acid starter batteries. Part 2. Dimensions of batteries and dimensions and marking of terminals

GOST R IEC 60269-1-2010: Low-voltage fuses. Part 1. General requirements

GOST R IEC 60297-3-101-2006: Mechanical structures for radio-electronic equipment. Subracks and associated plug-in units. Dimensions of mechanical structures of the 482,6 mm (19 in) series

GOST R IEC 60297-3-102-2006: Mechanical structures for radio-electronic equipment. Injector/extractor handle. Dimensions of mechanical structures of the 482,6 mm (19 in) series

GOST R IEC 60297-3-103-2006: Mechanical structures for radio-electronic equipment. Keying and alignment pin. Dimensions of mechanical structures of the 482,6 mm (19 in) series

GOST R IEC 60297-3-104-2009: Mechanical structures for electronic equipment. Connector dependent interface dimensions of subracks and plug-in units. Dimensions of mechanical structures of the 482,6 mm (19 in) series

GOST R IEC 60332-3-10-2005: Tests on electric and optical cables under fire conditions. Part 3-10. Flame spread of vertically-mounted bunched wires or cables. Apparatus

GOST R IEC 60332-3-10-2011: Tests on electric and optical fibre cables under fire conditions. Part 3-10. Flame spread of vertically-mounted bunched wires or cables. Apparatus

GOST R IEC 60332-3-21-2005: Tests on electric and optical cables under fire conditions. Рart 3-21. Flame spread of vertically-mounted bunched wires or cables. Category A F/R.

GOST R IEC 60332-3-22-2005: Tests on electric and optical cables under fire conditions. Рart 3-22. Flame spread of vertically-mounted bunched wires or cables. Category A.

GOST R IEC 60332-3-23-2005: Tests on electric and optical cables under fire conditions. Part 3-23. Flame spread of vertically-mounted bunched wires or cables. Category B

GOST R IEC 60332-3-24-2005: Tests on electric and optical cables under fire conditions. Part 3-24. Flame spread of vertically-mounted bunched wires or cables. Category C

GOST R IEC 60332-3-25-2005: Tests on electric and optical cables under fire conditions. Part 3-25. Flame spread of vertically-mounted bunched wires or cables. Category D

GOST R IEC 60384-14-2004: Fixed capacitors for use in electronic equipment. Part 14. Sectional specification on fixed capacitors for electromagnetic interference suppression and connection to the supply mains

GOST R IEC 60519-1-2005: Safety in electric heating equipment. Part 1. General requirements

GOST R IEC 60598-1-2011: Luminaires. Part 1. General requirements and test methods

GOST R IEC 60605-6-2007: Reliability in techniques. Tests for the validity of the constant failure rate and failure intensity

GOST R IEC 60745-1-2005: Hand-held motor-operated electric tools. Safety and test methods. Part 1. General requirements

GOST R IEC 60745-1-2009: Hand-held motor-operated electric tools. Safety and test methods. Part 1. General requirements

GOST R IEC 60745-2-11-2008: Hand-held motor-operated electric tools. Safety and test methods. Part 2-11. Particular requirements for reciprocating saws (jig and sabre saws)

GOST R IEC 60745-2-1-2006: Hand-held motor-operated electric tools. Safety and test methods. Part 2-1. Particular requirements for drills and impact drill machines

GOST R IEC 60745-2-12-2011: Hand-held motor-operated electric tools. Safety and test methods. Part 2-12. Particular requirements for concrete vibrators

GOST R IEC 60745-2-14-2007: Hand-held motor-operated electric tools. Safety and test methods. Part 2-14. Particular requirements for planers

GOST R IEC 60745-2-4-2008: Hand-held motor-operated electric tools. Safety and test methods. Part 2-4. Particular requirements for sanders and polishers other than disk type

GOST R IEC 60745-2-6-2007: Hand-held motor-operated electric tools. Safety and test methods. Part 2-6. Particular requirements for hammers and rotary hammers

GOST R IEC 60755-2012: General requirements for differential (residual) current operated protective devices

GOST R IEC 60838-1-2008: Miscellaneous lampholders. Part 1. General requirements and test methods

GOST R IEC 60917-2-3-2009: Mechanical structures for electronic equipment practices. Interface co-ordination dimensions for the 25 mm equipment practice. Dimensions for subracks, chassis, backplanes, front panels and plug-in units

GOST R IEC 60942-2009: Sound calibrators. Specifications and test requirements

GOST R IEC 60950-1-2005: Information technology equipment. Safety. Part 1. General requirements

GOST R IEC 61160-2006: Risk management. Formal design review

GOST R IEC 61161-2009: State system for ensuring the uniformity of measurements. Ultrasonic power in liquids. General requirements to measuring methods in the frequency range 0,5 to 25 MHz

GOST R IEC 61191-1-2010: Printed boards assemblies. Part 1. Surface mount and related assembly technologies. General technical requirements

GOST R IEC 61191-2-2010: Printed boards assemblies. Part 2. Surface mount. Technical requirements

GOST R IEC 61191-3-2010: Printed boards assemblies. Part 3. Sectional specification. Requirements for through-hole mount soldered assemblies

GOST R IEC 61191-4-2010: Printed boards assemblies. Part 4. Terminal mounting. Technical requirements

GOST R IEC 61192-1-2010: Soldered electronic assemblies. Workmanship requirements. Part 1. General technical requirements

GOST R IEC 61192-4-2010: Soldered electronic assemblies. Workmanship requirements. Part 4. Terminal assemblies

GOST R IEC 61192-5-2010: Soldered electronic assemblies. Workmanship requirements. Part 5. Rework, modification and repair

GOST R IEC 61207-1-2009: Gas analysers. Expression of performance. Part 1. General

GOST R IEC 61508-3-2007: Functional safety of electrical, electronic, programmable electronic safety-related systems. Part 3. Software requirements

GOST R IEC 61508-4-2007: Functional safety of electrical, electronic, programmable electronic safety-related systems. Part 4. Terms and definitions

GOST R IEC 61508-5-2007: Functional safety of electrical, electronic, programmable electronic safety-related systems. Part 5. Guidelines for methods of the determination of safety integrity levels

GOST R IEC 61508-7-2007: Functional safety of electrical, electronic, programmable electronic safety-related systems. Part 7. Techniques and measures

GOST R IEC 61557-3-2006: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 3. Loop impedance

GOST R IEC 61557-4-2007: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 4. Resistance of earth connection and equipotential bonding

GOST R IEC 61557-5-2008: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 5. Resistance to earth

GOST R IEC 61557-6-2009: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 6. Residual current operated protective devices in TT and TN systems

GOST R IEC 61557-7-2009: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 7. Phase sequence

GOST R IEC 61559-2-2012: Radiation protection instrumentation in nuclear facilities. Centralized systems for continuous radiation/control. Part 2. Requirements for discharge, environmental, accident or post-accident monitoring functions

GOST R IEC 61650-2007: Reliability in techniques. Procedures for comparison of constant failure rates and constant failure intensities

GOST R IEC 61996-1-2009: Maritime navigation and radiocommunication equipment and systems. Shipborne voyage data recorder (VDR). Part 1. Voyage data recorder (VDR). Technical and performance requirements, methods of testing and required test results

GOST R IEC 62127-1-2009: State system for ensuring the uniformity of measurements. Parameters of ultrasonic fields. General requirements to measuring methods and characterization of fields in the frequency range 0,5 to 40 MHz

GOST R IEC 62127-2-2009: State system for ensuring the uniformity of measurements. Hydrophones. General requirements for calibration methods in the frequency range up 40 MHz

GOST R IEC 62305-1-2010: Risk management. Protection against lightning. Part 1. General principles

GOST R IEC 62305-2-2010: Risk management. Protection against lightning. Part 2. Risk assessment

GOST R IEC 62384-2011: Electronic control gear supplied from the sources of direct or alternative current for light emitted diode modules. Performance requirements

GOST R IEC 62485-2-2011: Secondary batteries and battery installations. Safety requirements. Part 2. Stationary batteries

GOST R IEC 62560-2011: Self-ballasted LED-lamps for general lighting services by voltage 50 V. Safety specifications

GOST R ISO 10002-2007: Organization management. Customer satisfaction. Guidelines for complaints handling in organizations

GOST R ISO 10005-2007: Enterprise management. Guidelines for quality plans

GOST R ISO 10007-2007: Organization management. Guidelines for configuration management

GOST R ISO 10012-2008: Enterprise management. Measurement management systems. Requirements for measurement processes and measuring equipment

GOST R ISO 10014-2008: Enterprise management. Guidelines for realizing economic benefits in quality management system

GOST R ISO 10015-2007: Enterprise management. Guidelines for training

GOST R ISO 10019-2007: Organization management. Guidelines for the selection of quality management system consultants and use of their services

GOST R ISO 10075-2-2009: Ergonomic principles of assuring of adequacy of mental workload. Part 2. Design principles

GOST R ISO 10075-3-2009: Ergonomic principles of assuring of adequacy of mental workload. Part 3. Principles and requirements concerning methods for measuring and assessing mental workload

GOST R ISO 10140-1-2012: Acoustics. Laboratory measurement of sound insulation of building elements. Part 1. Testing rules for specific products

GOST R ISO 10155-2006: Stationary source emissions. Automated monitoring of mass concentrations of solid particles. Performance characteristics, test methods and technical requirements

GOST R ISO 10513-2009: Prevailing torque type all-metal hexagon nuts, style 2, with fine pitch thread. Property classes 8, 10 and 12

GOST R ISO 10576-1-2006: Statistical methods. Guidelines for the evaluation of conformity with specified requirements. Part 1. General principles

GOST R ISO 10664-2007: Star-type internal socket button for bolts and screws

GOST R ISO 10791-1-2009: Machining centres. Part 1. Geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z-axis)

GOST R ISO 10813-1-2011: Vibration. Guidance for selection of vibration generating machines. Part 1. Equipment for dynamic environmental testing

GOST R ISO 10846-1-2010: Vibration. Laboratory measurement of vibro-acoustic transfer properties of resilient elements. Part 1. General principles of measurements

GOST R ISO 10846-2-2010: Vibration. Laboratory measurement of vibro-acoustic transfer properties of resilient elements. Part 2. Direct method for determination of the dynamic stiffness of resilient supports for translatory motion

GOST R ISO 10846-5-2010: Mechanical vibration. Laboratory measurement of vibro-acoustic transfer properties of resilient elements. Part 5. Driving point method for determination of the low-frequency transfer stiffness of resilient supports for translatory motion

GOST R ISO 11064-7-2010: Ergonomic design of control centres. Part 7. Principles for evaluation

GOST R ISO 11095-2007: Statistical methods. Linear calibration using reference materials

GOST R ISO 11161-2010: Safety of machinery. Integrated manufacturing systems. Basic requirements

GOST R ISO 11228-1-2009: System of standards for labour safety. Ergonomics. Manual handling. Part 1. Lifting and carrying. General requirements

GOST R ISO 1140-2007: 3-, 4- and 8-strand polyamide fibre ropes. General specifications

GOST R ISO 1141-2007: 3-, 4- and 8-strand polyester fibre ropes. General specifications

GOST R ISO 11439-2010: Gas cylinders. High pressure cylinders for the on-board storage of natural gas as a fuel. Specifications

GOST R ISO 11462-1-2007: Statistical methods. Guidelines for implementation of statistical process control. Part 1. Elements

GOST R ISO 11464-2011: Soil quality. Pre-treatment of samples for physico-chemical analysis

GOST R ISO 11465-2011: Soil quality. Determination of dry matter and water content on a mass by gravimetric method

GOST R ISO 11476-2010: Paper and board. Method for determination of CIE whiteness. C/20 illuminant (indoor illumination)

GOST R ISO 11611-2011: Occupational safety standards system. Special clothing for protection against sparks and spatters of molten metal in welding and allied processes. Technical requirements

GOST R ISO 11612-2007: Occupational safety standards system. Clothing for protection against heat and flame. Test methods and performance requirements for heat-protective clothing

GOST R ISO 11614-2011: Reciprocating internal combustion compression-ignition engines. Apparatus for measurement of the opacity and for determination of the light absorption coefficient of exhaust gas

GOST R ISO 11648-1-2009: Statistical methods. Sampling from bulk materials. Part 1. General principles

GOST R ISO 11648-2-2009: Statistical methods. Sampling from bulk materials. Part 2. Sampling of particulate materials

GOST R ISO 1181-2007: 3-, 4- and 8-strand Manila and sisal fibre ropes. General specifications

GOST R ISO 11843-1-2007: Statistical methods. Capability of detection. Part 1. Terms and definitions

GOST R ISO 11843-2-2007: Statistical methods. Capability of detection. Part 2. Methodology in the linear calibration case

GOST R ISO 12126-2009: Prevailing torque type all-metal hexagon nuts with flange. Accuracy classes A and B

GOST R ISO 12127-1-2011: Occupational safety standards system. Clothing for protection against heat and flame. Determination of contact heat transmission through protective clothing or constituent materials. Part 1. Test method using heat produced by heating cylinder

GOST R ISO 12127-2007: Occupational safety standards system. Clothing for protection against heat and flame. Determination of contact heat transmission through protective clothing or constituent materials

GOST R ISO 12127-2-2011: Occupational safety standards system. Clothing for protection against heat and flame. Determination of contact heat transmission through protective clothing or constituent materials. Part 2. Test method using contact heat produced by dropping small cylinders

GOST R ISO 12156-1-2006: Diesel fuel. Determination of lubricity by the HFRR-apparatus. Part 1. Test method

GOST R ISO 12164-3-2011: Hollow taper shank of tools (HSK). Types T. Basic dimensions

GOST R ISO 12164-4-2011: Tool receiver for type T hollow taper shanks (HSK). Connecting dimensions

GOST R ISO 12491-2011: Building materials and components. Statistical methods for quality control

GOST R ISO 13381-1-2011: Condition monitoring and diagnostics of machines. Machine condition prognosis. Part 1. General guidelines

GOST R ISO 1346-2007: 3-, 4- and 8-strand polypropylene split film, monofilament and multifilament (PP2) and polypropylene high tenacity multifilament fibre ropes General specifications

GOST R ISO 13680-2011: Seamless casing, tubing and coupling stock from corrosion-resistant high-alloy steels and alloys for petroleum and natural gas industries. Specifications

GOST R ISO 13706-2006: Air cooled apparatus. General technical requirements

GOST R ISO 13736-2010: Combustible liquids. Determination of Abel closed-cup flash point

GOST R ISO 13752-2005: Air quality. Assessment of uncertainty of a measurement method under field conditions using a reference method

GOST R ISO 13759-2010: Petroleum products. Determination of alkyl nitrate in diesel fuels by spectrometric method

GOST R ISO 13879-2009: Perspective industrial technologies. Content and drafting of a functional specification for petroleum and natural gas industries

GOST R ISO 13880-2010: Perspective industrial technologies. Content and drafting of a technical specification for petroleum and natural gas industries

GOST R ISO 13898-1-2006: Steel and iron. Inductively coupled plasma atomic emission spectrometric method for determination of nickel, copper and cobalt contents. Part 1. General requirements

GOST R ISO 13898-2-2006: Steel and iron. Determination of nickel, copper and cobalt contents. Inductively coupled plasma atomic emission spectrometric method. Part 2. Determination of nickel content

GOST R ISO 14020-2011: Environmental labels and declarations. General principles

GOST R ISO 14064-1-2007: Greenhouse gases. Part 1. Specification with guidance at the organizational level for quantification and reporting of greenhouse gas emissions and removals

GOST R ISO 14064-2-2007: Greenhouse gases. Part 2: Specification with guidance at the project level for quantification, monitoring and reporting of greenhouse gas emission reductions or removal enhancements

GOST R ISO 14064-3-2007: Greenhouse gases. Part 3. Specification with guidance for the validation and verification of greenhouse gas assertions

GOST R ISO 14122-2-2010: Safety of machinery. Permanent means of access to machinery. Part 2. Working platforms and walkways.

GOST R ISO 14122-3-2009: Safety of machinery. Permanent means of access to machinery. Part 3. Stairs, stepladders and guard-rails.

GOST R ISO 14122-4-2009: Safety of machinery. Permanent means of access to machinery. Part 4. Vertical stairs

GOST R ISO 14507-2011: Soil quality. Pre-treatment of samples for determination of organic contaminants

GOST R ISO 14579-2009: Bolts with cylindrical head and star-type internal socket button

GOST R ISO 14583-2009: Star type socket pan cylindrical head screws

GOST R ISO 14839-1-2011: Vibration. Vibration of rotating machinery equipped with active magnetic bearings. Part 1. Terms and definitions

GOST R ISO 15025-2007: Occupational safety standards system. Protective clothing for protection against heat and flame. Method of test for limited flame spread

GOST R ISO 15265-2006: Risk management. Fundamentals of risk assessment strategy for the prevention of stress and discomfort in thermal working conditions

GOST R ISO 15489-1-2007: System of standards on information, librarianship and publishing. Records management. General requirements

GOST R ISO 15516-2011: Ships and marine technology. Launching appliances for davit-launched lifeboats

GOST R ISO 15547-1-2009: Petroleum and natural gas industries. Plate-type heat exchangers. Technical requirements

GOST R ISO 15614-2-2009: Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 2. Arc welding of aluminium and aluminium alloys

GOST R ISO 15665-2007: Noise. Guidelines for acoustic insulation of pipes and valves

GOST R ISO 15767-2007: Workplace atmospheres. Accuracy in weighing collected aerosols

GOST R ISO 16000-2-2007: Indoor air. Part 2. Sampling for formaldehyde content. Main principles

GOST R ISO 16121-1-2011: Ergonomic of vehicles. Requirements to the workplace of bus driver. Part 1. Basic requirements

GOST R ISO 16121-4-2011: Ergonomic of vehicles. Requirements for the workplace of bus driver. Part 4. Cabin work environment

GOST R ISO 16156-2008: Machine-tools safety. Jaw chucks

GOST R ISO 16269-6-2005: Statistical methods. Statistical interpretation of data. Determination of statistical tolerance intervals

GOST R ISO 16602-2010: Occupational safety standards system. Protective clothing for protection against chemicals. Classification, labelling and performance requirements

GOST R ISO 16889-2011: Hydraulic fluid power. Filters. Multi-pass method of transmission of fluid through the filter element for evaluating filtration performance

GOST R ISO 16932-2011: Glass and glass products. Destructive-windstorm-resistant security glazing. Test method and classification

GOST R ISO 17123-4-2011: State system for ensuring the uniformity of measurements. Optics and optical instruments. Field procedures for testing geodetic and surveying instruments. Part 4. Elektro-optical distance meters (EDM instruments)

GOST R ISO 17359-2009: Condition monitoring and diagnostics of machines. General guidelines on condition monitoring and diagnostics procedures

GOST R ISO 17491-3-2009: Occupational safety standards system. Protective clothing providing protection from chemicals. Part 3. Method for determination of resistance to penetration by a jet of liquid (jet test)

GOST R ISO 17666-2006: Risk management. Space systems

GOST R ISO 18414-2008: Statistical methods. Acceptance sampling procedures by attributes. Accept-zero sampling system based on credit reserve factor for product quality

GOST R ISO 1969-2007: 3- and 4-strand polyethylene fibre ropes. General specifications

GOST R ISO 2017-1-2011: Vibration and shock. Resilient mounting systems. Part 1. Technical information for the application of isolation systems

GOST R ISO 2017-2-2011: Mechanical vibration and shock. Resilient mounting systems. Part 2. Technical information for the application of vibration isolation associated with railway systems

GOST R ISO 21247-2007: Statistical methods. Combined accept-zero systems and process control procedures for sampling product

GOST R ISO 21467-2011: Earth-moving machinery. Horizontal direction drills. Terminology and specifications

GOST R ISO 22030-2009: Soil quality. Biological methods. Chronic phytotoxicity for higher plants

GOST R ISO 22673-2011: Ships and marine technologies. Launching appliances for free-fall lifeboats

GOST R ISO 22742-2006: Automatic identification. Bar coding. Linear bar code and two dimensional symbols for product packaging

GOST R ISO 22868-2007: Noise of machines. Noise test engineering method for portable hand-held forestry machines with petrol engine

GOST R ISO 230-1-2010: Machine tools tests. Part 1. Measurement techniques of geometrics parameters

GOST R ISO 2307-2007: Fibre ropes. Methods for determination of certain physical and mechanical properties

GOST R ISO 2531-2008: Ductile iron pipes, fittings, accessories and their joints for water or gas applications. Specifications

GOST R ISO 26382-2011: Cogeneration systems. General technical requirements

GOST R ISO 2780-2013: Milling cutters with tenon drive. Interchangeability dimensions for cutter arbours

GOST R ISO 2859-10-2008: Statistical methods. Sampling procedures for inspection by attributes. Part 10. Introduction to the GOST R ISO 2859 series of standards

GOST R ISO 2859-3-2009: Statistical methods. Sampling procedures for inspection by attributes. Part 3. Skip-lot sampling procedures

GOST R ISO 2859-4-2006: Statistical methods. Sampling procedures for inspection by attributes. Part 4. Assessment of declared quality level

GOST R ISO 2859-5-2009: Statistical methods. Sampling procedures for inspection by attributes. Part 5. System of sequential sampling plans indexed by AQL for lot-by-lot inspection

GOST R ISO 3183-2009: Steel pipes for pipelines of petroleum and natural gas industries. General specifications

GOST R ISO 3183-2-2007: Steel pipes for pipelines. Specifications. Part 2. Requirements for class B pipes

GOST R ISO 3183-3-2007: Steel pipes for pipelines. Specifications. Part 3. Requirements for class C pipes

GOST R ISO 3318-2013: Double-ended open-ended wrenches, double-headed box and combination. Widths of heads. Basic dimensions

GOST R ISO 3449-2009: Earth-moving machinery. Falling-object protective structures. Laboratory tests and performance requirements

GOST R ISO 3452-4-2011: Non-destructive testing. Penetrant testing. Part 4. Equipment

GOST R ISO 3675-2007: Crude petroleum and liquid petroleum products. Laboratory hydrometer method for determination of density

GOST R ISO 3679-2010: Methyl esters of fatty acids (FAME). Rapid equilibrium closed cup method of flash point determination

GOST R ISO 3734-2009: Petroleum products. Determination of water and sediment content in residual fuel oils by centrifuge method

GOST R ISO 389-1-2011: State system for ensuring the uniformity of measurements. Acoustics. Reference zero for the calibration of audiometric equipment. Part 1. Reference equivalent threshold sound pressure levels of pure tones for supra-aural earphones

GOST R ISO 389-7-2011: State system for ensuring the uniformity of measurements. Acoustics. Reference zero for the calibration of audiometric equipment. Part 7. Reference threshold of hearing under free-field and diffuse-field listening conditions

GOST R ISO 389-8-2011: State system for ensuring the uniformity of measurements. Acoustics. Reference zero for the calibration of audiometric equipment. Part 8. Reference equivalent threshold sound pressure levels of pure tones for circumaural earphones

GOST R ISO 3951-5-2009: Statistical methods. Sampling procedures for inspection by variables. Part 5. Sequential sampling plans indexed by AQL for known standard deviation

GOST R ISO 4014-2013: Hexagon head bolts. Product grades A and B

GOST R ISO 4040-2011: Ergonomics of vehicles. Location of hand controls, indicators and tell-tales in motor vehicle

GOST R ISO 4175-2006: Shipbuilding. Shipborne barges, series 1. Main dimensions

GOST R ISO 5010-2006: Earth-moving machinery. Rubber-tyred machines. Steering capability

GOST R ISO 5010-2009: Earth-moving machinery. Steering systems for rubber-tyred machines

GOST R ISO 5725-1-2002: Accuracy (trueness and precision) of measurement methods and results. Part 1. General principles and definitions

GOST R ISO 580-2008: Plastics piping systems. Injection-moulded thermoplastics fittings. Methods for determination of fittings appearance alteration after heating

GOST R ISO 6385-2007: Ergonomics. Ergonomic principles in the design of work systems

GOST R ISO 6507-1-2007: Metals and alloys. Vickers hardness test. Part 1. Test method

GOST R ISO 6772-2011: Aerospace. Fluid systems. Impulse testing of hydraulic hose, tubing and fitting assemblies

GOST R ISO 6942-2007: Occupational safety standards system. Clothing for protection against heat and fire. Assessment methods of materials and material assemblies when exposed to а source of radiant heat

GOST R ISO 7042-2011: Prevailing torque type all-metal hexagon nuts, style 2. Property classes 5, 8, 10 and 12

GOST R ISO 7044-2009: Prevailing torque type all-metal hexagon nuts with flange. Accuracy classes A and B

GOST R ISO 7222-2005: Shipbuilding. Shipborne barges, series 2. Main dimensions

GOST R ISO 7243-2007: Hot environments. Estimation of the heat stress on working man, based on the WBGT-index (wet bulb globe temperature)

GOST R ISO 7619-2-2009: Rubber, vulcanized or thermoplastic. Determination of indentation hardness. Part 2. IRHD pocket meter method of measurement

GOST R ISO 7661-2010: Clamp blocks for tube lines having axial alignment. Technical requirements and test methods

GOST R ISO 7731-2007: Ergonomics. Danger signals for public and work areas. Auditory danger signals

GOST R ISO 7870-1-2011: Statistical methods. Control charts. Part 1. General guidelines

GOST R ISO 8082-2005: Self-propelled machinery for forestry. Roll-over protective structures. Performance requirements and test methods

GOST R ISO 8084-2005: Machinery for forestry. Operator protective structures. Performance requirements and test methods

GOST R ISO 8106-2010: Glass containers. Determination of capacity by gravimetric method

GOST R ISO 8303-2005: Shipbuilding. Shipborne barges, series 3. Main operational and technical requirements

GOST R ISO 8385-2011: Ships and marine technology. Dredgers. Classification

GOST R ISO 8528-2-2007: Reciprocating internal combustion engine driven alternating current generating sets. Part 2. Internal combustion engines

GOST R ISO 8528-7-2007: Reciprocating internal combustion engine driven alternating current generating sets. Part 7. Technical declarations for specification and design

GOST R ISO 8568-2010: Shock testing machines. Declaration and verification of characteristics

GOST R ISO 8991-2011: Fasteners. Designation system

GOST R ISO 9016-2011: Destructive tests on welds in metallic materials. Test for impact bending. Test specimen location, notch orientation and examination

GOST R ISO 9096-2006: Stationary source emissions. Manual determination of mass concentration of particulate matter

GOST R ISO 9151-2007: Occupational safety standards system. Protective clothing against heat and flame. Method for determination of heat transmission on exposure to flame

GOST R ISO 9185-2007: Occupational safety standards system. Special protective clothing. Assessment methods of resistance to molten metal splash

GOST R ISO 9241-11-2010: Ergonomic requirements for office work with visual display terminals (VDTs). Part 11. Guidance on usability

GOST R ISO 9241-1-2007: Ergonomic requirements for office work with visual display terminals (VDTs). Part 1. General introduction

GOST R ISO 9329-4-2010: Seamless tubes from austenitic high-alloy steels for pressure purposes. Specifications

GOST R ISO 9686-2009: Direct reduced iron. Determination of carbon and/or sulphur content. Method of infrared spectroscopy after sample burning in induction furnace

GOST R ISO 9727-1-2009: Cylindrical cork stoppers. Methods for determination of physical properties. Part 1. Determination of dimensions

GOST R ISO 9727-2-2012: Cylindrical cork stoppers. Methods for determination of physical properties. Part 2. Determination of mass and apparent density for agglomerated cork stoppers

GOST R ISO 9727-3-2010: Cylindrical cork stoppers. Methods for determination of physical properties. Part 3. Determination of humidity content

GOST R ISO 9727-4-2010: Cylindrical cork stoppers. Methods for determination of physical properties. Part 4. Determination of dimensional recovery after compression

GOST R ISO 9727-6-2012: Cylindrical cork stoppers. Methods for determination of physical properties. Part 6. Determination of liquid tightness

GOST R ISO 9727-7-2010: Cylindrical cork stoppers. Methods for determination of physical properties. Part 7. Determination of dust quantity

GOST R ISO 9886-2008: Ergonomics of the thermal environment. Evaluation of thermal strain by physiological measurements

GOST R ISO 9934-1-2011: Non-destructive testing. Magnetic particle testing. Part 1. General principles

GOST R ISO/IEC 13335-1-2006: Information technology. Security techniques. Part 1. Concepts and models for information and communications technology security management

GOST R ISO/IEC 15288-2005: Information technology. System engineering. System life cycle processes

GOST R ISO/IEC 15419-2005: Automatic identification. Bar coding. Bar code digital imaging and printing systems. General and performance requirements

GOST R ISO/IEC 15423-2005: Automatic identification. Bar coding. General requirements for bar code scanner and decoder performance testing

GOST R ISO/IEC 15459-3-2007: Automatic identification. International unique identifiers. Part 3. Common rules for unique identifiers

GOST R ISO/IEC 15459-4-2007: Automatic identification. International unique identifiers. Part 4. Unique identifiers of individual items for supply chain management

GOST R ISO/IEC 15459-5-2008: Automatic identification. International unique identifiers. Part 5. Unique identifiers for returnable transport items

GOST R ISO/IEC 15459-6-2009: Automatic identification. Unique identifiers. Part 6. Unique identifiers for product groupings

GOST R ISO/IEC 15963-2005: Automatic identification. Radio frequency identification for item management. Unique identification for RF tags

GOST R ISO/IEC 16085-2007: Risk management. Application for system and software life cycle processes

GOST R ISO/IEC 17030-2007: General requirements for third party marks of conformity

GOST R ISO/IEC 19785-1-2008: Automatic identification. Biometrics. Common biometric exchange formats framework. Part 1. Data element specification

GOST R ISO/IEC 19785-2-2008: Information identification. Biometrics. Common biometric exchange formats framework. Part 2. Procedures for the operation of the biometric registration authority

GOST R ISO/IEC 19794-10-2010: Automatic identification. Biometric identification. Biometric data interchange formats. Part 10. Hand geometry silhouette data

GOST R ISO/IEC 19794-4-2006: Automatic identification. Biometrics. Biometric data interchange formats. Part 4. Finger image data

GOST R ISO/IEC 19794-5-2006: Automatic identification. Biometrics. Biometric data interchange formats. Part 5. Face image data

GOST R ISO/IEC 19794-6-2006: Automatic identification. Biometrics. Biometric data interchange formats. Part 6. Iris image data

GOST R ISO/IEC 19795-2-2008: Automatic identification. Biometrics. Biometric performance testing and reporting. Part 2. Testing methodologies for technology and scenario evaluation

GOST R ISO/IEC 24713-2-2011: Information technology. Biometrics. Biometric profiles for interoperability and data interchange. Part 2. Physical access control for employees at airports

GOST R ISO/IEC 27004-2011: Information technology. Security techniques. Information security management. Measurement

GOST R ISO/IEC 27005-2010: Information technology. Security techniques. Information security risk management

GOST R ISO/IEC 27033-1-2011: Information technology. Security techniques. Network security. Part 1. Overview and concepts

GOST R ISO/IEC 29109-5-2013: Information technology. Biometrics. Conformance testing methodology for biometric data interchange formats defined in ISO/IEC 19794. Part 5. Face image data

GOST R ISO/IEC 29794-1-2012: Information technology. Biometrics. Biometric sample quality. Part 1. Framework

GOST R ISO/IEC 31010-2011: Risk management. Risk assessment methods

GOST R ISO/IEC TO 10032-2007: Reference model of data management

GOST R ISO/IEC TO 13335-4-2007: Information technology. Security techniques. Part 4. Selection of safeguards

GOST R ISO/IEC TO 13335-5-2006: Information technology. Security techniques. Part 5. Management guidance on network security

GOST R ISO/IEC TO 19795-3-2009: Automatic identification. Biometrics. Part 3. Modality-specific testing

GOST R ISO/TR 10013-2007: Organization management. Guidelines for quality management system documentation

GOST R ISO/TR 10014-2005: Guidelines for managing the economics of quality

GOST R ISO/TR 8550-1-2007: Statistical methods. Guide to the selection and usage of acceptance sampling systems for inspection of discrete items in lots. Part 1. General requirements

GOST R ISO/TS 10303-1051-2009: Industrial automation systems and integration. Product data representation and exchange. Part 1051. Application module. Geometric tolerance

GOST R ISO/TS 10303-1151-2009: Industrial automation systems and integration. Product data representation and exchange. Part 1151. Application module: Functional data

GOST R ISO/TS 10303-1156-2009: Industrial automation systems and integration. Product data representation and exchange. Part 1156. Application module. Product structure and classification

GOST R ISO/TS 14048-2009: Environmental management. Life cycle assessment. Data documentation format

GOST R ISO/TS 22745-11-2009: Industrial automation systems and integration. Open technical dictionaries and their application to master data. Part 11. Guidelines for the formulation of terminology

GOST R ISO/TS 22745-1-2009: Industrial automation systems and integration. Open technical dictionaries and their application to master data. Part 1. Overview and fundamental principles

GOST R ISO/TS 22745-13-2009: Industrial automation systems and integration. Open technical dictionaries and their application to catalogues. Part 13. Identification of concepts and terminology

GOST R ISO/TS 22745-20-2009: Industrial automation systems and integration. Open technical dictionaries and their application to master data. Part 20. Procedures for the maintenance of an Open Technical Dictionary

GOST R ISO/TS 22745-30-2009: Industrial automation systems and integration. Open technical dictionaries and their application to master data. Part 30. Identification guide representation

GOST R ISO/TS 8000-1-2009: Data quality. Part 1. Overview

GOST R ISO/TU 13732-2-2008: Ergonomics of the thermal environment. Methods for the assessment of human responses to contact with surfaces. Part 2. Contact with moderate temperature surface

GOST R ISO/TU 29001-2007: Enterprise management. Requirements for quality management systems of product and service supply organizations in petroleum, petrochemical and natural gas industries

MDS 12-27.2006: Methodological manual for conducting labor protection training for executives and specialists of construction organizations

MI 2525-99: State system for ensuring uniformity of measurements. Recommendations on metrology of state scientific metrology centers of Gosstandart of Russia. Order of development

MI 2526-99: State system for ensuring uniformity of measurements. Regulatory documents on methods of calibration of measuring instruments. Main provisions

MI 2646-2001: GSOEI. Description of the type of measuring instruments for the State Register. The order of construction and general requirements for the presentation and design

MI 2976-2006: Recommendation. State system for ensuring uniformity of measurements. Construction, content and presentation of documents governing the methods of quantitative chemical analysis

MI 3195-2009: Recommendation. State system for ensuring uniformity of measurements. Load power voltage transformers, the method of measurement without disconnecting circuits

MI 3196-2009: Recommendation. State system for ensuring uniformity of measurements. Secondary load current transformers. The method of measurement without disconnecting the circuit

MUK 4.1.001-13: Methods of measuring the mass concentration of formaldehyde in samples of drinking, natural, treated wastewater and melted snow (snow) by the photometric method

MUK 4.1.002-13: Methods of measuring the mass concentration of 1, 1-dimethylhydrazine in washes from equipment surfaces, building structures, skin and personal protective equipment by photometric method

MUK 4.1.003-13: Measurement of mass concentration of 1, 1-dimethylhydrazine in the blood by spectrophotometric method

MUK 4.1.004-13: Method for measuring the mass concentration of ammonium perchlorate (perchlorate ion) in the urine by the potentiometric method

MUK 4.1.005-13: Methods for measuring the mass concentration of tetramethyl tetrazene in the air of the working area by the photometric method

MUK 4.1.006-13: Methods of measuring the mass concentration of formaldehyde in the air of the working area by the photometric method

MUK 4.1.007-13: Methods of measuring the mass concentration of nitrogen dioxide in the air of the working area by the photometric method

MUK 4.1.008-13: Method for measuring the mass concentration of dimethylamine in samples of drinking, natural, treated wastewater and snowmelt (snow) by the photometric method

MUK 4.1.015-11: Methods of measuring the mass fraction of tetramethyltetrazene in soil samples by the photometric method

MUK 4.1.016-11: Methods of measuring the mass fraction of nitrosodimethylamine in soil samples by the photometric method

MUK 4.1.017-11: Methods of measuring the mass concentration of nitrosodimethylamine in the air of the working area by the photometric method

MUK 4.1.019-11: Measurement method of the mass fraction of 1, 1-dimethylhydrazine in soil samples by photometric method

MUK 4.1.058-10: Methods for measuring the mass concentration of epichlorohydrin in the air of the working area by the photometric method

MUK 4.4.052-08: Measurement of ambient dose equivalent and ambient equivalent dose of gamma radiation using gamma radiation dosimeters DKG-02U Arbiter, DKG-01D Garant, DKG-03D Grach, MKS RM-1401K radiation monitoring in an emergency

ODM 218.1.001-2005: Recommendations for the development and application of technical regulation documents in the field of road facilities

ODM 218.1.001-2010: Recommendations for the development and application of technical regulation documents in the field of road facilities

ODM 218.1.002-2010: Recommendations for the organization and conduct of work on standardization in the road sector

ODM 218.2.007-2011: Guidelines for the design of measures to ensure the access of persons with disabilities to road facilities

ODM 218.2.064-2015: Methods for strengthening the slopes of the roadbed of roads by sowing grass in various climatic zones

ODM 218.2.067-2016: Guidelines for the selection of rational structures of the roadbed on weak grounds and their feasibility study

ODM 218.2.069-2016: Recommendations for the design of approaches of the roadbed on a weak base to artificial structures

ODM 218.3.032-2013: Guidelines for strengthening the structural elements of roads by spatial geogrids

ODM 218.5.001-2009: Guidelines for the use of geogrids and flat geogrids for the reinforcement of asphalt concrete layers of improved types of coatings for the overhaul and repair of roads

ODM 218.8.012-2019: Guidelines (guidance) on the predictive assessment of environmental impact during the construction and operation of public roads

OST 45.150-99: Measurement Techniques. Order of development and certification

OST 45.173-2000: Industry standardization system. Procedure of the introduction of the international (regional) documents in the field of telecommunications as the national regulatory documents

OST 45.177-2000: Industry Standardization System. Regulatory documents on floppy disks. The order of execution and treatment

OST 45.180-2000: Industry Standardization System. Abbreviations in industry regulations. Application procedure

OST 45.182-2001: Industry Standardization System. Technical requirements for telecommunications. Requirements for content and presentation

OST 45.52-97: Industry Standardization System. The procedure for developing enterprise standards

OST 45.53-97: Industry Standardization System. The procedure for developing rules and recommendations for standardization

OST 45.59-98: The industry standardization system. Main provisions

OST 45.89-2000: Industry Standardization System. Publication of regulatory documents of the industry. Requirements for the preparation of regulatory documents, the procedure for publication and distribution

OST 95 10560-2001: Physical inventory of nuclear material. Order of conduction

PR 50.1.008-95: Organization and performance of work on international standardization in the Russian Federation

R 50.1.011-96: State supervision of compliance with the mandatory requirements of state standards at the stages of development, preparation for the production and operation of industrial products

R 50.1.035-2001: Порядок применения международных и региональных стандартов в Российской Федерации

R 50.1.038-2002: Standardization of terms and definitions in the field of defense products. General provisions

R 50.1.071-2010: Nanotechnologies. Principles, objects of standardization and types of documents in the field of standardization of nanotechnologies, nanomaterials and products of nanoindustry

R 50.1.075-2011: Development of Standards on Terms and Definitions

R 50.1.076-2011: Organization management. Customer service methods

R 50.1.077-2011: Information technologies. Free software. Rules for use

R 50.2.061-2008: General criteria for the competence of certified reference material producers

R 52.04.714-2008: Methodology for calculating the indicator of compliance with standard volumes of work on monitoring urban air pollution

R 78.36.017-2010: Recommendations on the choice and use of locks for protective structures

R 78.36.033-2013: Application monitoring and comparative analysis of testing various types of window units, blinds, security grilles and glazing. Classification, methods of installation and strengthening of the structure. Guidelines

R 78.36.034-2013: Application monitoring and comparative analysis of tests of various types of perimeter fencing (main fencing, additional fencing, preventive external and internal fencing) Classification

RD 153-39-026-97: Requirements for Chemical Products, Ensuring Their Safe Use in the Oil Industry

RD 34.01.602-94: Methodical guidelines on development and maintenance of normative and technical documents fund and on information support of electric power enterprises (organization) units with them

RD 52.04.688-2006: Provision on methodological guidance for monitoring the state and pollution of the environment. Part 1. Meteorological, actinometric and heat balance observations

RD 52.14.28-98: Instructions. The procedure for the development and circulation of industry guidance documents and recommendations

RD 52.14.617-2000: Instructions. The order of the norm control

RD 52.19.751-2010: Evaluation of hydrometeorological observations and work

RD-APK 3.00.01.01-08: Procedure for Development, Style, Format, Review, Approval, and Registration of Engineering Design Standards, Industry-Specific Building Codes, and Guidelines

RMG 94-2009: State system for ensuring the uniformity of measurements. Test laboratories performing of the quality control of oil at acceptance operations. Basic requirements

RT 02-2008: Organization of verification of measuring instruments and the procedure for developing documents on verification methods

RTM 68-8.10-95: Measurement procedure. Requirements for the construction, content, representation and metrological certification

SDA 06-2008: Terms and definitions used in the unified conformity assessment system at facilities controlled by the Federal Service for Environmental, Technological and Nuclear Supervision

SDA-06-2009: Terms and definitions used in the Unified system of conformity assessment in the field of industrial, environmental safety, safety in the energy sector and construction

SO 003-02495342-2006: Floors. Methods for assessing the slipperiness of floor coverings

SO 004-02495342-2006: Floors. Method for the evaluation of floor coverings for sparking at shock effects

TSN 23-310-2000: Energy efficiency in residential and public buildings. Standards for thermal protection of buildings. Belgorod region

TSN 23-311-2000: Energy efficiency of residential and public buildings. Standards for thermal protection of buildings. Smolensk region

TSN 23-355-2004: Energy efficiency of residential and public buildings. Standards for energy consumption and heat protection. Kirov region

Turkmenistan Guidelines for the development and application of standards: Guidelines for the development and application of standards for unavoidable losses and waste of materials in construction

VSP 33-03-07 MO RF: Instructions for the design of the slope and through the protective structures and special underwater stands

Customers Who Viewed This Item Also Viewed:

Rules of Electrical Installations Design (Russian Electrical Code). 7th Edition. All sections and exhibits
Language: English
Price: $478.76
Foundation bolts. Structure and dimensions
Language: English
Price: $198.99
Pipeline valves. Leakage rates of valves
Language: English
Price: $173.25
Hot-rolled sheet. Range
Language: English
Price: $72.27
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $108.90
Flanges for valves, fittings and pipelines for pressure to PN 250. Design, dimensions and general technical requirements
Language: English
Price: $293.04
Stainless steels and corrosion resisting, heat-resisting and creep resisting alloys. Grades
Language: English
Price: $212.85
State system for ensuring the uniformity of measurements. Verification of testing equipment. General principles
Language: English
Price: $121.77
Billet of rotor shafts and rings of turbine generators
Language: English
Price: $1,487.33
Steel building structures. General specifications
Language: English
Price: $250.17
Fencing constructions for translucent buildings and structures. Design rules
Language: English
Price: $609.15
Metal products from structural alloy steel. Specification
Language: English
Price: $371.25
Obosnovanie bezopasnosti oborudovaniya. Rekomendatsii po podgotovke
Language: English
Price: $67.32
Reinforcing rolled products for reinforced concrete constructions. Specifications
Language: English
Price: $298.98
Electromagnetic compatibility of multimedia equipment. Emission requirements
Language: English
Price: $974.64
Non-destructive testing. Method of magnetic particle testing. Standard technological processes
Language: English
Price: $292.05
Supports for Cylindrical and Conical Upright Apparatus. Types and Basic Parameters
Language: English
Price: $573.20
Rolling stock of railways. Springs cylindrical screw. Certification requirements
Language: English
Price: $175.65
Steel structures
Language: English
Price: $297.00
Tests on electric and optical cables under fire conditions. Part 3-22. Flame spread of vertically-mounted bunched wires or cables. Category A
Language: English
Price: $102.96

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!